On Tue, Sep 19, 2017 at 9:57 PM, Sandy Huang <hjc@xxxxxxxxxxxxxx> wrote:
>
>
> 在 2017/9/20 9:51, Sandy Huang 写道:
>>
>> Hi rob,
>> thanks for you review.
>>
>> 在 2017/9/19 22:46, Rob Herring 写道:
>>>
>>> On Thu, Sep 14, 2017 at 11:43:18AM +0800, Sandy Huang wrote:
>>>>
>>>> This path add support rv1108 rgb output interface driver.
>>>>
>>>> Signed-off-by: Sandy Huang <hjc@xxxxxxxxxxxxxx>
>>>> ---
>>>> .../bindings/display/rockchip/rockchip-rgb.txt | 80
>>>> ++++++++++++++++++++++
>>>> 1 file changed, 80 insertions(+)
>>>> create mode 100644
>>>> Documentation/devicetree/bindings/display/rockchip/rockchip-rgb.txt
>>>>
>>>> diff --git
>>>> a/Documentation/devicetree/bindings/display/rockchip/rockchip-rgb.txt
>>>> b/Documentation/devicetree/bindings/display/rockchip/rockchip-rgb.txt
>>>> new file mode 100644
>>>> index 0000000..4164512
>>>> --- /dev/null
>>>> +++
>>>> b/Documentation/devicetree/bindings/display/rockchip/rockchip-rgb.txt
>>>> @@ -0,0 +1,80 @@
>>>> +Rockchip RV1108 RGB interface
>>>> +================================
>>>> +
>>>> +Required properties:
>>>> +- compatible: matching the soc type:
>>>> + - "rockchip,rv1108-rgb";
>>>> +
>>>> +Optional properties:
>>>> +- pinctrl-names: must contain a "lcdc" entry.
>>>> +- pinctrl-0: pin control group to be used for this interface.
>>>> +
>>>> +Required nodes:
>>>> +- rockchip,rgb-mode: should be "p888", "p666", "p565", "s888",
>>>> "s888-dummy"
>>>
>>>
>>> This should be a standard property. Any device with a parallel interface
>>> is going to need something like this.
>>>
>> so, i need to move this property to panel? or just rename
>> rockchip,rgb-mode to rgb-mode?
>>
>>>> + - p888: output r8-g8-b8 at each dclk cycle for per-pixel
>>>> + - p666: output r6-g6-b6 at each dclk cycle for per-pixel
>>>> + - p565: output r5-g6-b5 at each dclk cycle for per-pixel
>>>> + - s888: output r8-g8-b8 in three dclk cycle for per-pixel
>>>> + - s888-dmmy: output r8-g8-b8-dummy in four dclk cycle for per-pixel
>>>> +
>>>> +The rgb has two video ports described by:
>>>> + Documentation/devicetree/bindings/media/video-interfaces.txt
>>>> +Their connections are modeled using the OF graph bindings specified in
>>>> + Documentation/devicetree/bindings/graph.txt.
>>>> +
>>>> +- video port 0 for the VOP input, the remote endpoint maybe
>>>> vopb/vopl/vop
>>>> +- video port 1 for either a panel or subsequent encoder
>>>> +
>>>> +the panel described by:
>>>> + Documentation/devicetree/bindings/display/panel/simple-panel.txt
>>>> +Panel other required properties:
>>>> +- ports for remote rgb output.
>>>> +
>>>> +Example:
>>>> +
>>>> +panel: panel {
>>>> + compatible = "auo,b101ean01";
>>>> + enable-gpios = <&gpio7 21 GPIO_ACTIVE_HIGH>;
>>>> +
>>>> + ports {
>>>> + panel_in_rgb: endpoint {
>>>> + remote-endpoint = <&rgb_out_panel>;
>>>> + };
>>>> + };
>>>> +};
>>>> +
>>>> +For Rockchip RV1108:
>>>> +
>>>> + rgb: rgb {
>>>> + compatible = "rockchip,rv1108-rgb";
>>>> + pinctrl-names = "lcdc";
>>>> + pinctrl-0 = <&lcdc_ctl>;
>>>> + rockchip,rgb-mode = "p888";
>>>> +
>>>> + ports {
>>>> + #address-cells = <1>;
>>>> + #size-cells = <0>;
>>>> +
>>>> + rgb_in: port@0 {
>>>> + reg = <0>;
>>>> + #address-cells = <1>;
>>>> + #size-cells = <0>;
>>>> +
>>>> + rgb_in_vop: endpoint@0 {
>>>> + reg = <0>;
>>>
>>>
>>> Don't need reg for a single endpoint.
>>>
>> ok, this will be deleted at next version.
>>>>
>>>> + remote-endpoint = <&vop_out_rgb>;
>>>> + };
>>>> + };
>>>> +
>>>> + rgb_out: port@1 {
>>>> + reg = <1>;
>>>> + #address-cells = <1>;
>>>> + #size-cells = <0>;
>>>> +
>>>> + rgb_out_panel: endpoint@0 {
>>>> + reg = <0>;
>>>
>>>
>>> ditto.
>>>
>> ok, this will be deleted at next version.
>
> sorry,this can't be deleted, because rgb output remote endpoint maybe panel
> or convert chip, the dts node maybe like this:
>
> panel: panel {
> status = "disabled";
> ports {
> panel_in_rgb: endpoint {
> remote-endpoint = <&rgb_out_panel>;
> };
> };
> };
>
> bridge: bridge {
> status = "okay";
> ports {
> bridge_in_rgb: endpoint {
> remote-endpoint = <&rgb_out_bridge>;
> };
> };
> };
>
> rgb_out: port@1 {
> reg = <1>;
> #address-cells = <1>;
> #size-cells = <0>;
> rgb_out_panel: endpoint@0 {
> reg = <0>;
> remote-endpoint = <&panel_in_rgb>;
> };
> rgb_out_bridge: endpoint@1 {
> reg = <1>;
> remote-endpoint = <&bridge_in_rgb>;
> };
> };
>
> so rockchip_rgb_bind() @ rockchip_rgb.c use reg id to find the remote
> actived endpoint.
>
> for_each_child_of_node(port, endpoint) {
> of_property_read_u32(endpoint, "reg", &endpoint_id);
Lack of reg property here should imply 0 for endpoint_id.
> ret = drm_of_find_panel_or_bridge(dev->of_node, 1, endpoint_id,
> &rgb->panel, &rgb->bridge);
> if (!ret)
> break;
> }
>
>>>> + remote-endpoint = <&panel_in_rgb>;
>>>> + };
>>>> + };
>>>> + };
>>>> + };
>>>> --
>>>> 2.7.4
>>>>
>>>>
>>>
>>>
>>>
>>
>>
>> _______________________________________________
>> Linux-rockchip mailing list
>> Linux-rockchip@xxxxxxxxxxxxxxxxxxx
>> http://lists.infradead.org/mailman/listinfo/linux-rockchip
>
>
_______________________________________________
dri-devel mailing list
dri-devel@xxxxxxxxxxxxxxxxxxxxx
https://lists.freedesktop.org/mailman/listinfo/dri-devel
