On Tue, Aug 29, 2017 at 08:20:41PM -0500, Forest Crossman wrote: > Hi, all, > > I recently bough a bunch of udl-compatible DisplayLink adapters and > have been trying to use them in Linux, but have been running into some > issues: > > - Output is limited to 16-bit color, but the device is capable of 24-bit color. > - X providers (not sure if that's the right term--it's the output of > `xrandr --listproviders`) often linger when plugging and unplugging > multiple adapters. e.g., I normally have one provider (my main GPU) > with no adapters plugged in, then I'll plug in three DisplayLink > adapters and there will be four (or five!) providers, and then I'll > unplug one and there will still be four (or five), and if I plug it in > again it'll add another provider, etc. > - The driver only uses RLE to compress data, but the devices are > capable of (better?) Huffman coding-based compression. > - Not exactly a udl issue, but the udlfb module has to be blacklisted > to enable the use of udl. > - The entire driver hangs if you plug in the adapter while preventing > the DisplayLink SoC from reading the adapter's internal I2C EEPROM. > Yes, I realize this happened because I was messing around with the > electronics inside the adapter, but a USB device should probably not > be permitted to cause a driver to hang in the first place. > - Not really a functional issue, but the driver is very "chatty" in > its dmesg output, printing a bunch of non-fatal error messages when > things go wrong. > - When things do go wrong, the driver creates the X provider even if > there's a bunch of errors in the kernel log. This is just my opinion, > but I think if a problem is so bad it prints an error message, the > device init should fail and not result in the X provider being > created. If it's really not that bad, then it should probably be just > a warning. > - The driver seems to check for the EDID of connected monitors on all > adapters whenever a new adapter is connected, regardless of whether > there are any monitors connected to any of those adapters, and then it > outputs error messages when it fails to read the EDIDs of the > unconnected monitors. > - The vendor descriptor is output with DRM_INFO when a new device is > connected, which seems unnecessarily verbose. > > Since I haven't done any kernel dev before, I thought that fixing some > of these issues might be a good introduction. However, I'm not > entirely sure what I'm doing, and the commit history of the driver > doesn't seem to tell the whole story as to why certain design > decisions were made, so I have a few questions: > > - Why only 16-bit color? I realize that the lower 8 bits need to be > stored and transferred in another buffer, but is there a technical > reason why this isn't already implemented? Or was there just not much > interest in adding that functionality at the time? > - Why isn't there support for the Huffman coding compression? Was it > for technical reasons, e.g., more things need to be reverse > engineered, performance, etc.? Or just lack of interest/developer > time? > - Why are there two drivers for these devices (udl and udlfb)? Would > it be possible to merge all the functionality into udl so I don't have > to blacklist udlfb on every computer I want to use these adapters > with? We have a bunch of other such cases, the solution is to just not compile _any_ of the fbdev drivers. You still need fbdev itself, plus fbcon, for the kernel console, but the fbdev drivers should all be drm drivers which provide fbdev support through the fbdev emulation layer we have. If your distro enables udlfb, your distro is doing it wrong. > - What parts of the driver should I be looking into to fix the X > provider duplication issue? > - Why is there so much pointer math? (e.g., `*cmd++ = val;`). Is this > normal for kernel code? > - Why is the driver version still "0.0.1" and the driver date > "20120220"? Should these be updated? > > I apologize if any of the questions I'm asking sound silly--as I said > before, I'm new to this and I'm still learning how it all works. > > I figured that fixing the 16-bit/24-bit issue wouldn't be too > difficult, so I've already done a little driver hacking and managed to > add a bunch of code to output the lower 8-bits of pixel data to the > device. Unfortunately, it's all very hacky, crashes pretty often, and > doesn't actually work. I know how to use libusb pretty well, but the > kernel USB API is new to me, so I'm pretty sure that's where most of > my problems are right now. Then again, I also just might not fully > understand the hardware yet, either. > > If anyone has any answers/comments/advice on how to fix those issues, > I'd love to hear them! Also, if you need more detailed issue > descriptions, I can do some more testing and provide those as well. UDL is defacto unmaintained, so if you have such a huge issue list I recommend you dive into the code and have fun. There's some patches floating around on dri-devel already, but because unmaintained, no one really looks at them. For small drm drivers we have drm-misc with commit rights, so barrier to get this all going is super low (by kernel standards, it's still nowhere near opening pull requests on github or similar). -Daniel -- Daniel Vetter Software Engineer, Intel Corporation http://blog.ffwll.ch _______________________________________________ dri-devel mailing list dri-devel@xxxxxxxxxxxxxxxxxxxxx https://lists.freedesktop.org/mailman/listinfo/dri-devel
