This adds device tree bindings for the Ilitek ILI9322
320x240 TFT panel driver.
Cc: devicetree@xxxxxxxxxxxxxxx
Signed-off-by: Linus Walleij <linus.walleij@xxxxxxxxxx>
---
.../bindings/display/panel/ilitek,ili9322.txt | 120 +++++++++++++++++++++
1 file changed, 120 insertions(+)
create mode 100644 Documentation/devicetree/bindings/display/panel/ilitek,ili9322.txt
diff --git a/Documentation/devicetree/bindings/display/panel/ilitek,ili9322.txt b/Documentation/devicetree/bindings/display/panel/ilitek,ili9322.txt
new file mode 100644
index 000000000000..d619b1ad14a6
--- /dev/null
+++ b/Documentation/devicetree/bindings/display/panel/ilitek,ili9322.txt
@@ -0,0 +1,120 @@
+Ilitek ILI9322 TFT panel driver with SPI control bus
+
+This is a driver for 320x240 TFT panels, accepting a variety of input
+streams that get adapted and scaled to the panel. The panel output has
+960 TFT source driver pins and 240 TFT gate driver pins, VCOM, VCOML and
+VCOMH outputs.
+
+Required properties:
+ - compatible: "ilitek,ili9322"
+ - reg: address of the panel on the SPI bus
+
+Optional properties:
+ - width-mm: physical panel width [mm]
+ - height-mm: physical panel height [mm]
+ - vcc-supply: core voltage supply, see regulator/regulator.txt
+ - iovcc-supply: voltage supply for the interface input/output signals,
+ see regulator/regulator.txt
+ - vci-supply: voltage supply for analog parts, see regulator/regulator.txt
+ - reset-gpios: a GPIO spec for the reset pin, see gpio/gpio.txt
+ - ilitek,vreg1out-microvolt: the output in microvolts for the VREGOUT1
+ regulator used to drive the physical display. Valid ranges are 3600 thru
+ 6000 in 100 microvolt increments. If not specified, hardware defaults will
+ be used (4.5V).
+ - ilitek,vcom-amplitude-percent: the percentage of VREGOUT1 used for the
+ peak-to-peak amplitude of the communcation signals to the physical display.
+ Valid ranges are 70 thru 132 percent in increments if two percent. Odd
+ percentages will be truncated. If not specified, hardware defaults will be
+ used (114%).
+ - ilitek,vcom-high-percent: the percentage of VREGOUT1 used for the peak
+ voltage on the communications link. Valid ranges are 37 thru 100 percent.
+ If not specified, hardware defaults will be used (91%).
+ - ilitek,gamma-correction-neg: a set of 8 nybbles describing negative
+ gamma correction for voltages V1 thru V8. Valid range 0..15
+ - ilitek,gamma-correction-pos: a set of 8 nybbles describing positive
+ gamma correction for voltages V1 thru V8. Valid range 0..15
+ These adjust what grayscale voltage will be output for input data V1 = 0,
+ V2 = 16, V3 = 48, V4 = 96, V5 = 160, V6 = 208, V7 = 240 and V8 = 255.
+ The curve is shaped like this:
+
+ ^
+ | V8
+ | V7
+ | V6
+ | V5
+ | V4
+ | V3
+ | V2
+ | V1
+ +----------------------------------------------------------->
+ 0 16 48 96 160 208 240 255
+
+ The negative and postive gamma values adjust the V1 thru V8 up/down
+ according to the datasheet specifications. This is a property of the
+ physical display connected to the display controller and may vary.
+ If defined, both arrays must be supplied in full. If the properties
+ are not supplied, hardware defaults will be used.
+
+ - ilitek,entry-mode: the panel can be connected to various input streams
+ and four of them can be selected by electronic straps on the display.
+ However it is possible to select another mode or override the
+ electronic default with this property. Valid values:
+ 0: 8 bit serial RGB through
+ 1: 8 bit serial RGB aligned
+ 2: 8 bit serial RGB dummy 320x240
+ 3: 8 bit serial RGB dummy 360x240
+ 4: disabled
+ 5: 24 bit parallel RGB through
+ 6: 24 bit parallel RGB aligned
+ 7: 24 bit YUV 640Y 320CbCr
+ 8: 24 bit YUV 720Y 360CbCr
+ 9: disabled
+ 10: 8 bit ITU-R BT.656 720Y 360CbCr
+ 11: 8 bit ITU-R BT.656 640Y 320CbCr
+
+ The following optional properties only apply to RGB and YUV input modes and
+ can be omitted for BT.656 input modes:
+
+ - flip-horizontal: flip the image horizontally (right-to-left scan)
+ - flip-vertical: flip the image vertically (down-to-up scan)
+ - pixelclk-active: see display/panel/display-timing.txt
+ - de-active: see display/panel/display-timing.txt
+ - hsync-active: see display/panel/display-timing.txt
+ - vsync-active: see display/panel/display-timing.txt
+
+The panel must obey the rules for a SPI slave device as specified in
+spi/spi-bus.txt
+
+The device node can contain one 'port' child node with one child
+'endpoint' node, according to the bindings defined in
+media/video-interfaces.txt. This node should describe panel's video bus.
+
+Example:
+
+panel: display@0 {
+ compatible = "ilitek,ili9322";
+ reg = <0>;
+ /* 50 ns min period = 20 MHz */
+ spi-max-frequency = <20000000>;
+ spi-cpol; /* Clock active low */
+ /* Panel LM918A01-1A SY-B4-091116-E0199 */
+ width-mm = <65>;
+ height-mm = <50>;
+ ilitek,entry-mode = <11>;
+ ilitek,vreg1out-microvolt = <4600>;
+ ilitek,vcom-high-percent = <91>;
+ ilitek,vcom-amplitude-percent = <114>;
+ ilitek,gamma-correction-neg = <0xa>, <0x5>, <0x7>,
+ <0x7>, <0x7>, <0x5>, <0x1>, <0x6>;
+ ilitek,gamma-correction-pos = <0x7>, <0x7>, <0x3>,
+ <0x2>, <0x3>, <0x5>, <0x7>, <0x2>;
+ vcc-supply = <&vdisp>;
+ iovcc-supply = <&vdisp>;
+ vci-supply = <&vdisp>;
+
+ port {
+ panel_in: endpoint {
+ remote-endpoint = <&display_out>;
+ };
+ };
+};
--
2.13.4
_______________________________________________
dri-devel mailing list
dri-devel@xxxxxxxxxxxxxxxxxxxxx
https://lists.freedesktop.org/mailman/listinfo/dri-devel
