On 08/04/2017 02:39 PM, Laurent Pinchart wrote:
Hi David,
On Friday 04 Aug 2017 10:51:37 David Lechner wrote:
On 08/04/2017 09:54 AM, Laurent Pinchart wrote:
On Thursday 03 Aug 2017 17:33:47 David Lechner wrote:
This adds a new binding for Sitronix ST7586 display panels.
Using lego as the vendor prefix in the compatible string because the
display panel I am working with is an integral part of the LEGO
MINDSTORMS EV3.
Signed-off-by: David Lechner <david@xxxxxxxxxxxxxx>
---
.../bindings/display/sitronix,st7586.txt | 26
+++++++++++++++++++
1 file changed, 26 insertions(+)
create mode 100644
Documentation/devicetree/bindings/display/sitronix,st7586.txt
diff --git
a/Documentation/devicetree/bindings/display/sitronix,st7586.txt
b/Documentation/devicetree/bindings/display/sitronix,st7586.txt new file
mode 100644
index 0000000..dfb0b7b
--- /dev/null
+++ b/Documentation/devicetree/bindings/display/sitronix,st7586.txt
@@ -0,0 +1,26 @@
+Sitronix ST7586 display panel
+
+Required properties:
+- compatible: "lego,ev3-lcd".
+
+The node for this driver must be a child node of a SPI controller, hence
+all mandatory properties described in ../spi/spi-bus.txt must be
specified. +
+Optional properties:
+- dc-gpios: D/C pin. The presence/absence of this GPIO determines
+ the panel interface operation mode (IF[3:1] pins):
+ - present: IF=011 4-wire 8-bit data serial interface
+ - absent: IF=010 3-wire 9-bit data serial interface
How does this work ? Do you have a single GPIO on your system connected to
IF[1], with IF[3:2] hardwired to 01 ?
LEGO has not made the internals of the display publicly available, so I
cannot say for sure. But I assume that IF[3:1] is hardwired to 011. This
causes pin D1 to assigned to the signal A0, which is what we are calling
the dc gpio here.
If IF[3:1] were hardwired to 010, then pin D1 would be not not used and
there would be no A0 signal.
So, basically, we can infer the state of IF[3:1] by the fact that we
have a dc pin or not.
OK, now I understand what you mean. Maybe you should phrase it a bit
differently to make it clearer ? How about
dc-gpios: Specified or the GPIO connected to the panel's D/C pin (also called
A0). The property is required when the panel operates in 4-wire mode (IF[3:1]
= 011) and prohibited when the panel operates in 3-wire mode (IF[3:1] = 010).
Yes, this is more clear. Thank you for the suggestion.
By the way, if the signal is named A0, why don't you call the property a0-
gpios ?
I consider "dc-gpios" to be a generic name since it is used by many
different panels. But I would be OK with calling it "a0-gpios" as well.
It will just require more explanation that this is the A0 *signal* and
not the A0 *pin*. The actual pin used is labeled *D1* on the controller.
On the other hand, it is labeled as A0 on LEGO's schematic, so perhaps
a0 is better.
+- reset-gpios: Reset pin
+- power-supply: A regulator node for the supply voltage.
+- backlight: phandle of the backlight device attached to the panel
+- rotation: panel rotation in degrees counter clockwise
(0,90,180,270)
Please use the OF graph DT bindings (a.k.a. ports) to describe the
connection between the panel and its source.
I am afraid that I do not understand this request. What would the source
of the panel be? There is nothing like a SoC LCD controller that is
driving this panel.
My bad, I should have read the panel datasheet before replying :-S Please
ignore this comment.
+Example:
+ display@0{
+ compatible = "lego,ev3-lcd";
+ reg = <0>;
+ spi-max-frequency = <10000000>;
+ dc-gpios = <&gpio 43 GPIO_ACTIVE_HIGH>;
+ reset-gpios = <&gpio 80 GPIO_ACTIVE_HIGH>;
+ };
_______________________________________________
dri-devel mailing list
dri-devel@xxxxxxxxxxxxxxxxxxxxx
https://lists.freedesktop.org/mailman/listinfo/dri-devel
