On Fri, Jul 28, 2017 at 04:23:11PM +0100, Liviu Dudau wrote: > On Wed, Jul 26, 2017 at 11:27:48AM +0100, Russell King - ARM Linux wrote: > > On Wed, Jul 26, 2017 at 11:05:39AM +0100, Russell King wrote: > > > Some ARM platforms do not wire the HDLCD interrupt. Allow hdlcd to > > > initialise without an interrupt present. > > > > > > Signed-off-by: Russell King <rmk+kernel@xxxxxxxxxxxxxxx> > > > > Hi Russell, > > Sorry for my silence, I was on holiday this week and just came back > today. > > > This isn't fully functional on ARM MPS platforms yet, but at least > > gets us further. Without any display connected: > > > > [ 14.315986] [drm] found ARM HDLCD version r0p0 > > [ 14.557038] tda998x 2-0070: found TDA19988 > > [ 14.622232] hdlcd 40205000.hdlcd: bound 2-0070 (ops 0x213534) > > [ 14.630406] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013). > > [ 14.639335] [drm] No driver support for vblank timestamp query. > > [ 14.653210] [drm] Cannot find any crtc or sizes - going 1024x768 > > [ 15.232556] hdlcd 40205000.hdlcd: fb0: frame buffer device > > [ 15.284076] [drm] Initialized hdlcd 1.0.0 20151021 for 40205000.hdlcd on minor 0 > > > > With a TV connected, the driver doesn't initialise: > > > > [ 14.422810] [drm] found ARM HDLCD version r0p0 > > [ 14.657227] tda998x 2-0070: found TDA19988 > > [ 14.722439] hdlcd 40205000.hdlcd: bound 2-0070 (ops 0x213534) > > [ 14.730613] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013). > > [ 14.739538] [drm] No driver support for vblank timestamp query. > > [ 15.311977] hdlcd 40205000.hdlcd: Failed to set initial hw configuration. > > [ 15.357402] hdlcd 40205000.hdlcd: master bind failed: -12 > > [ 15.365082] tda998x: probe of 2-0070 failed with error -12 > > > > I don't think this is correct behaviour - if we fail to set an initial > > configuration (which will be based on the resolution of the connected > > display) why should the driver fail to probe - it's not that there is > > no device, it's (in this case) that there aren't the resources for the > > chosen mode. Userspace could always try setting a different mode. > > > > I suspect the above failure is down to either (a) not having enough > > memory available to allocate a 1920x1080 frame buffer, or (b) not > > (yet) being able to program the hdlcd pixel clock for this platform, > > which is currently hard-coded in DT at 23.75MHz. > > I don't think it is the clock, if that fails then you would not see the > r0p0 version number being printed. Due to the fact that until now HDLCD > has run mostly on platforms that have SCP, which takes care of actual > setup of the clocks, it is pretty lax on errors on pixel clock setup. Note, however, that in this case, the clock is a fixed frequency clock. I wasn't meaning a failure to obtain the clock, I was meaning a failure to set the appropriate rate. > Also, may I ask what MPS platform you are trying to use? I might be able > to source one internally and try to reproduce your problems. I'll point you in the direction of Ian Rickards in ARM for that information. (I'm not sure if I can mention the board publically yet as its early days...) -- RMK's Patch system: http://www.armlinux.org.uk/developer/patches/ FTTC broadband for 0.8mile line: currently at 9.6Mbps down 400kbps up according to speedtest.net. _______________________________________________ dri-devel mailing list dri-devel@xxxxxxxxxxxxxxxxxxxxx https://lists.freedesktop.org/mailman/listinfo/dri-devel
