On Fri, 2017-05-12 at 17:31 -0700, Puthikorn Voravootivat wrote:
>
>
>
> On Fri, May 12, 2017 at 5:12 PM, Pandiyan, Dhinakaran
> <dhinakaran.pandiyan@xxxxxxxxx> wrote:
> On Thu, 2017-05-11 at 16:02 -0700, Puthikorn Voravootivat
> wrote:
> > Read desired PWM frequency from panel vbt and calculate the
> > value for divider in DPCD address 0x724 and 0x728 to have
> > as many bits as possible for PWM duty cyle for granularity
> of
> > brightness adjustment while the frequency is still within
> 25%
> > of the desired frequency.
>
> I read a few eDP panel data sheets, the PWM frequencies all
> start from
> ~200Hz. If the VBT chooses this lowest value to allow for more
> brightness control, and then this patch lowers the value by
> another 25%,
> we'll end up below the panel allowed PWM frequency.
>
> In fact, one of the systems I checked had PWM frequency as
> 200Hz in VBT
> and the panel datasheet also had PWM frequency range starting
> from
> 200Hz. Have you considered this case?
>
> The spec said "A given LCD panel typically has a limited range of
> backlight frequency capability.
> To limit the programmable frequency range, limitations are placed on
> the allowable total divider ratio with the Sink device"
> So I think it should be auto cap to 200Hz in this case.
>
> -DK
> >
> > Signed-off-by: Puthikorn Voravootivat <puthik@xxxxxxxxxxxx>
> > ---
> > drivers/gpu/drm/i915/intel_dp_aux_backlight.c | 81
> +++++++++++++++++++++++++++
> > 1 file changed, 81 insertions(+)
> >
> > diff --git a/drivers/gpu/drm/i915/intel_dp_aux_backlight.c
> b/drivers/gpu/drm/i915/intel_dp_aux_backlight.c
> > index 0b48851013cc..6f10a2f1ab76 100644
> > --- a/drivers/gpu/drm/i915/intel_dp_aux_backlight.c
> > +++ b/drivers/gpu/drm/i915/intel_dp_aux_backlight.c
> > @@ -113,12 +113,86 @@
> intel_dp_aux_set_dynamic_backlight_percent(struct intel_dp
> *intel_dp,
> > }
> > }
> >
> > +/*
> > + * Set PWM Frequency divider to match desired frequency in
> vbt.
> > + * The PWM Frequency is calculated as 27Mhz / (F x P).
> > + * - Where F = PWM Frequency Pre-Divider value programmed
> by field 7:0 of the
> > + * EDP_BACKLIGHT_FREQ_SET register (DPCD
> Address 00728h)
> > + * - Where P = 2^Pn, where Pn is the value programmed by
> field 4:0 of the
> > + * EDP_PWMGEN_BIT_COUNT register (DPCD Address
> 00724h)
> > + */
> > +static void intel_dp_aux_set_pwm_freq(struct
> intel_connector *connector)
> > +{
> > + struct drm_i915_private *dev_priv =
> to_i915(connector->base.dev);
> > + struct intel_dp *intel_dp =
> enc_to_intel_dp(&connector->encoder->base);
> > + int freq, fxp, fxp_min, fxp_max, fxp_actual, f = 1;
> > + u8 pn, pn_min, pn_max;
> > +
> > + /* Find desired value of (F x P)
> > + * Note that, if F x P is out of supported range, the
> maximum value or
> > + * minimum value will applied automatically. So no
> need to check that.
> > + */
> > + freq = dev_priv->vbt.backlight.pwm_freq_hz;
> > + DRM_DEBUG_KMS("VBT defined backlight frequency %u Hz
> \n", freq);
> > + if (!freq) {
> > + DRM_DEBUG_KMS("Use panel default backlight
> frequency\n");
> > + return;
> > + }
> > +
> > + fxp = KHz(DP_EDP_BACKLIGHT_FREQ_BASE_KHZ) / freq;
> > +
> > + /* Use highest possible value of Pn for more
> granularity of brightness
> > + * adjustment while satifying the conditions below.
> > + * - Pn is in the range of Pn_min and Pn_max
> > + * - F is in the range of 1 and 255
> > + * - Effective frequency is within 25% of desired
> frequency.
> > + */
> > + if (drm_dp_dpcd_readb(&intel_dp->aux,
> > +
> DP_EDP_PWMGEN_BIT_COUNT_CAP_MIN, &pn_min) != 1) {
> > + DRM_DEBUG_KMS("Failed to read pwmgen bit count
> cap min\n");
> > + return;
> > + }
> > + if (drm_dp_dpcd_readb(&intel_dp->aux,
> > +
> DP_EDP_PWMGEN_BIT_COUNT_CAP_MAX, &pn_max) != 1) {
> > + DRM_DEBUG_KMS("Failed to read pwmgen bit count
> cap max\n");
> > + return;
> > + }
> > + pn_min &= DP_EDP_PWMGEN_BIT_COUNT_MASK;
> > + pn_max &= DP_EDP_PWMGEN_BIT_COUNT_MASK;
> > +
> > + fxp_min = fxp * 3 / 4;
> > + fxp_max = fxp * 5 / 4;
>
>
> You are allowing fxp between +/- 25% of the actual. This isn't
> same as
> the "Effective frequency is within 25% of desired frequency."
> right? The
> frequency can vary between -20% and +33%.
>
>
> You are right.
> You want me to change commit message to reflect this or change the
> code to
> match the commit message?
I am okay with fixing the comment and commit message. Is the 25%
arbitrary or based on the distances between the possible values? Please
make a note in the comment if it's the former.
> > + if (fxp_min < (1 << pn_min) || (255 << pn_max) <
> fxp_max) {
> > + DRM_DEBUG_KMS("VBT defined backlight frequency
> out of range\n");
> > + return;
> > + }
> > +
> > + for (pn = pn_max; pn > pn_min; pn--) {
Is there a reason this is not pn >= pn_min?
> > + f = clamp(fxp >> pn, 1, 255);
> > + fxp_actual = f << pn;
> > + if (fxp_min <= fxp_actual && fxp_actual <=
> fxp_max)
> > + break;
> > + }
> > +
> > + if (drm_dp_dpcd_writeb(&intel_dp->aux,
> > + DP_EDP_PWMGEN_BIT_COUNT, pn) <
> 0) {
> > + DRM_DEBUG_KMS("Failed to write aux pwmgen bit
> count\n");
If the number of brightness control bits are changing, the max.
brightness value changes too.
Please see intel_dp_aux_setup_backlight().
> > + return;
> > + }
> > + if (drm_dp_dpcd_writeb(&intel_dp->aux,
> > + DP_EDP_BACKLIGHT_FREQ_SET, (u8)
> f) < 0) {
> > + DRM_DEBUG_KMS("Failed to write aux backlight
> freq\n");
> > + return;
> > + }
> > +}
> > +
> > static void intel_dp_aux_enable_backlight(struct
> intel_connector *connector)
> > {
> > struct intel_dp *intel_dp =
> enc_to_intel_dp(&connector->encoder->base);
> > uint8_t dpcd_buf = 0;
> > uint8_t new_dpcd_buf = 0;
> > uint8_t edp_backlight_mode = 0;
> > + bool freq_cap;
> >
> > if (drm_dp_dpcd_readb(&intel_dp->aux,
> > DP_EDP_BACKLIGHT_MODE_SET_REGISTER,
> &dpcd_buf) != 1) {
> > @@ -151,6 +225,10 @@ static void
> intel_dp_aux_enable_backlight(struct intel_connector
> *connector)
> > DRM_DEBUG_KMS("Enable dynamic brightness.\n");
> > }
> >
> > + freq_cap = intel_dp->edp_dpcd[2] &
> DP_EDP_BACKLIGHT_FREQ_AUX_SET_CAP;
> > + if (freq_cap)
> > + new_dpcd_buf |=
> DP_EDP_BACKLIGHT_FREQ_AUX_SET_ENABLE;
> > +
> > if (new_dpcd_buf != dpcd_buf) {
> > if (drm_dp_dpcd_writeb(&intel_dp->aux,
> > DP_EDP_BACKLIGHT_MODE_SET_REGISTER,
> new_dpcd_buf) < 0) {
> > @@ -158,6 +236,9 @@ static void
> intel_dp_aux_enable_backlight(struct intel_connector
> *connector)
> > }
> > }
> >
> > + if (freq_cap)
> > + intel_dp_aux_set_pwm_freq(connector);
> > +
> > set_aux_backlight_enable(intel_dp, true);
> > intel_dp_aux_set_backlight(connector,
> connector->panel.backlight.level);
> > }
>
>
>
>
> _______________________________________________
> Intel-gfx mailing list
> Intel-gfx@xxxxxxxxxxxxxxxxxxxxx
> https://lists.freedesktop.org/mailman/listinfo/intel-gfx
_______________________________________________
dri-devel mailing list
dri-devel@xxxxxxxxxxxxxxxxxxxxx
https://lists.freedesktop.org/mailman/listinfo/dri-devel
