Read desired PWM frequency from panel vbt and calculate the
value for divider in DPCD address 0x724 and 0x728 to match
that frequency as close as possible.
Signed-off-by: Puthikorn Voravootivat <puthik@xxxxxxxxxxxx>
---
drivers/gpu/drm/i915/intel_dp_aux_backlight.c | 71 +++++++++++++++++++++++++++
1 file changed, 71 insertions(+)
diff --git a/drivers/gpu/drm/i915/intel_dp_aux_backlight.c b/drivers/gpu/drm/i915/intel_dp_aux_backlight.c
index fc26fea94fd4..441ad434a82b 100644
--- a/drivers/gpu/drm/i915/intel_dp_aux_backlight.c
+++ b/drivers/gpu/drm/i915/intel_dp_aux_backlight.c
@@ -113,12 +113,76 @@ intel_dp_aux_set_dynamic_backlight_percent(struct intel_dp *intel_dp,
}
}
+/*
+ * Set PWM Frequency divider to match desired frequency in vbt.
+ * The PWM Frequency is calculated as 27Mhz / (F x P).
+ * - Where F = PWM Frequency Pre-Divider value programmed by field 7:0 of the
+ * EDP_BACKLIGHT_FREQ_SET register (DPCD Address 00728h)
+ * - Where P = 2^Pn, where Pn is the value programmed by field 4:0 of the
+ * EDP_PWMGEN_BIT_COUNT register (DPCD Address 00724h)
+ */
+static void intel_dp_aux_set_pwm_freq(struct intel_connector *connector)
+{
+ struct drm_i915_private *dev_priv = to_i915(connector->base.dev);
+ struct intel_dp *intel_dp = enc_to_intel_dp(&connector->encoder->base);
+ int freq, fxp, f;
+ u8 pn, pn_min, pn_max;
+
+ /* Find desired value of (F x P)
+ * Note that, if F x P is out of supported range, the maximum value or
+ * minimum value will applied automatically. So no need to check that.
+ */
+ freq = dev_priv->vbt.backlight.pwm_freq_hz;
+ DRM_DEBUG_KMS("VBT defined backlight frequency %u Hz\n", freq);
+ if (!freq) {
+ DRM_DEBUG_KMS("Use panel default backlight frequency\n");
+ return;
+ }
+
+ fxp = DP_EDP_BACKLIGHT_FREQ_BASE / freq;
+
+ /* Use lowest possible value of Pn to try to make F to be between 1 and
+ * 255 while still in the range Pn_min and Pn_max
+ */
+ if (drm_dp_dpcd_readb(&intel_dp->aux,
+ DP_EDP_PWMGEN_BIT_COUNT_CAP_MIN, &pn_min) != 1) {
+ DRM_DEBUG_KMS("Failed to read pwmgen bit count cap min\n");
+ return;
+ }
+ if (drm_dp_dpcd_readb(&intel_dp->aux,
+ DP_EDP_PWMGEN_BIT_COUNT_CAP_MAX, &pn_max) != 1) {
+ DRM_DEBUG_KMS("Failed to read pwmgen bit count cap max\n");
+ return;
+ }
+ pn_min &= DP_EDP_PWMGEN_BIT_COUNT_MASK;
+ pn_max &= DP_EDP_PWMGEN_BIT_COUNT_MASK;
+
+ f = fxp >> pn_min;
+
+ for (pn = pn_min; pn < pn_max && f > 255; pn++)
+ f >>= 1;
+
+ f = clamp(f, 1, 255);
+
+ if (drm_dp_dpcd_writeb(&intel_dp->aux,
+ DP_EDP_PWMGEN_BIT_COUNT, pn) < 0) {
+ DRM_DEBUG_KMS("Failed to write aux pwmgen bit count\n");
+ return;
+ }
+ if (drm_dp_dpcd_writeb(&intel_dp->aux,
+ DP_EDP_BACKLIGHT_FREQ_SET, (u8) f) < 0) {
+ DRM_DEBUG_KMS("Failed to write aux backlight freq\n");
+ return;
+ }
+}
+
static void intel_dp_aux_enable_backlight(struct intel_connector *connector)
{
struct intel_dp *intel_dp = enc_to_intel_dp(&connector->encoder->base);
uint8_t dpcd_buf = 0;
uint8_t new_dpcd_buf = 0;
uint8_t edp_backlight_mode = 0;
+ bool freq_cap;
if (drm_dp_dpcd_readb(&intel_dp->aux,
DP_EDP_BACKLIGHT_MODE_SET_REGISTER, &dpcd_buf) != 1) {
@@ -150,6 +214,10 @@ static void intel_dp_aux_enable_backlight(struct intel_connector *connector)
DRM_DEBUG_KMS("Enable dynamic brightness.\n");
}
+ freq_cap = intel_dp->edp_dpcd[2] & DP_EDP_BACKLIGHT_FREQ_AUX_SET_CAP;
+ if (freq_cap)
+ new_dpcd_buf |= DP_EDP_BACKLIGHT_FREQ_AUX_SET_ENABLE;
+
if (new_dpcd_buf != dpcd_buf) {
if (drm_dp_dpcd_writeb(&intel_dp->aux,
DP_EDP_BACKLIGHT_MODE_SET_REGISTER, new_dpcd_buf) < 0) {
@@ -157,6 +225,9 @@ static void intel_dp_aux_enable_backlight(struct intel_connector *connector)
}
}
+ if (freq_cap)
+ intel_dp_aux_set_pwm_freq(connector);
+
set_aux_backlight_enable(intel_dp, true);
intel_dp_aux_set_backlight(connector, connector->panel.backlight.level);
}
--
2.13.0.rc1.294.g07d810a77f-goog
_______________________________________________
dri-devel mailing list
dri-devel@xxxxxxxxxxxxxxxxxxxxx
https://lists.freedesktop.org/mailman/listinfo/dri-devel
