On 10.03.2017 05:32, Sean Paul wrote:
> From: Lin Huang <hl@xxxxxxxxxxxxxx>
>
> AUX errors are caused by many different reasons. We may not know what
> happened in aux channel on failure, so let's reset aux channel if some
> errors occurred.
>
> Cc: 征增 王 <wzz@xxxxxxxxxxxxxx>
> Cc: Douglas Anderson <dianders@xxxxxxxxxxxx>
> Signed-off-by: Lin Huang <hl@xxxxxxxxxxxxxx>
> Signed-off-by: Sean Paul <seanpaul@xxxxxxxxxxxx>
Reviewed-by: Andrzej Hajda <a.hajda@xxxxxxxxxxx>
Few questions below:
> ---
> drivers/gpu/drm/bridge/analogix/analogix_dp_reg.c | 18 ++++++++++++++----
> 1 file changed, 14 insertions(+), 4 deletions(-)
>
> diff --git a/drivers/gpu/drm/bridge/analogix/analogix_dp_reg.c b/drivers/gpu/drm/bridge/analogix/analogix_dp_reg.c
> index 377bee4e20fd..1cb57e528ec8 100644
> --- a/drivers/gpu/drm/bridge/analogix/analogix_dp_reg.c
> +++ b/drivers/gpu/drm/bridge/analogix/analogix_dp_reg.c
> @@ -465,6 +465,10 @@ void analogix_dp_init_aux(struct analogix_dp_device *dp)
> reg = RPLY_RECEIV | AUX_ERR;
> writel(reg, dp->reg_base + ANALOGIX_DP_INT_STA);
>
> + analogix_dp_set_analog_power_down(dp, AUX_BLOCK, true);
> + usleep_range(10, 11);
> + analogix_dp_set_analog_power_down(dp, AUX_BLOCK, false);
> +
> analogix_dp_reset_aux(dp);
>
> /* Disable AUX transaction H/W retry */
> @@ -1158,7 +1162,7 @@ ssize_t analogix_dp_transfer(struct analogix_dp_device *dp,
> reg, !(reg & AUX_EN), 25, 500 * 1000);
> if (ret) {
> dev_err(dp->dev, "AUX CH enable timeout!\n");
> - return -ETIMEDOUT;
> + goto aux_error;
> }
>
> /* TODO: Wait for an interrupt instead of looping? */
> @@ -1167,7 +1171,7 @@ ssize_t analogix_dp_transfer(struct analogix_dp_device *dp,
> reg, reg & RPLY_RECEIV, 10, 20 * 1000);
> if (ret) {
> dev_err(dp->dev, "AUX CH cmd reply timeout!\n");
> - return -ETIMEDOUT;
> + goto aux_error;
> }
>
> /* Clear interrupt source for AUX CH command reply */
> @@ -1177,7 +1181,7 @@ ssize_t analogix_dp_transfer(struct analogix_dp_device *dp,
> reg = readl(dp->reg_base + ANALOGIX_DP_INT_STA);
> if (reg & AUX_ERR) {
> writel(AUX_ERR, dp->reg_base + ANALOGIX_DP_INT_STA);
> - return -EREMOTEIO;
> + goto aux_error;
> }
>
> /* Check AUX CH error access status */
> @@ -1185,7 +1189,7 @@ ssize_t analogix_dp_transfer(struct analogix_dp_device *dp,
> if ((reg & AUX_STATUS_MASK)) {
> dev_err(dp->dev, "AUX CH error happened: %d\n\n",
> reg & AUX_STATUS_MASK);
> - return -EREMOTEIO;
> + goto aux_error;
> }
>
> if (msg->request & DP_AUX_I2C_READ) {
> @@ -1211,4 +1215,10 @@ ssize_t analogix_dp_transfer(struct analogix_dp_device *dp,
> msg->reply = DP_AUX_NATIVE_REPLY_ACK;
>
> return num_transferred > 0 ? num_transferred : -EBUSY;
> +
> +aux_error:
> + /* if aux err happen, reset aux */
> + analogix_dp_init_aux(dp);
> +
> + return -EREMOTEIO;
You are masking original error values here, is it intended?
> }
_______________________________________________
dri-devel mailing list
dri-devel@xxxxxxxxxxxxxxxxxxxxx
https://lists.freedesktop.org/mailman/listinfo/dri-devel
