+ Thierry for real
On Tue, Mar 21, 2017 at 03:26:35PM -0400, Sean Paul wrote:
> On Wed, Mar 15, 2017 at 03:19:13PM +0800, Chris Zhong wrote:
> > Support Innolux P079ZCA 7.85" 768x1024 TFT LCD panel, it is a MIPI DSI
> > panel.
> >
> > Signed-off-by: Chris Zhong <zyw@xxxxxxxxxxxxxx>
> > ---
> >
> > Changes in v2:
> > - add some error check
> > - always use Low power mode to send commend
> > - add comments for all the sleep
> > - use DRM_DEV_ERROR instead of dev_err
> >
>
> Minor suggestion below. Once that's cleared up, you can add:
> Reviewed-by: Sean Paul <seanpaul@xxxxxxxxxxxx>
>
> Also, please add Thierry directly to your patches so he sees them.
>
>
> > drivers/gpu/drm/panel/Kconfig | 11 +
> > drivers/gpu/drm/panel/Makefile | 1 +
> > drivers/gpu/drm/panel/panel-innolux-p079zca.c | 344 ++++++++++++++++++++++++++
> > 3 files changed, 356 insertions(+)
> > create mode 100644 drivers/gpu/drm/panel/panel-innolux-p079zca.c
> >
>
> <snip>
> > +static int innolux_panel_prepare(struct drm_panel *panel)
> > +{
> > + struct innolux_panel *innolux = to_innolux_panel(panel);
> > + int err, ret;
> > +
> > + if (innolux->prepared)
> > + return 0;
> > +
> > + gpiod_set_value_cansleep(innolux->enable_gpio, 0);
> > +
> > + err = regulator_enable(innolux->supply);
> > + if (err < 0)
> > + return err;
> > +
> > + /* T2: 15ms - 1000ms */
> > + usleep_range(15000, 16000);
> > +
> > + gpiod_set_value_cansleep(innolux->enable_gpio, 1);
> > +
> > + /* T4: 15ms - 1000ms */
> > + usleep_range(15000, 16000);
> > +
> > + err = mipi_dsi_dcs_exit_sleep_mode(innolux->link);
> > + if (err < 0) {
> > + DRM_DEV_ERROR(panel->dev, "failed to exit sleep mode: %d\n",
> > + err);
> > + goto poweroff;
> > + }
> > +
> > + /* T6: 120ms - 1000ms*/
> > + msleep(120);
> > +
> > + err = mipi_dsi_dcs_set_display_on(innolux->link);
> > + if (err < 0) {
> > + DRM_DEV_ERROR(panel->dev, "failed to set display on: %d\n",
> > + err);
> > + goto poweroff;
> > + }
> > +
> > + /* T7: 5ms */
> > + usleep_range(5000, 6000);
> > +
> > + innolux->prepared = true;
> > +
> > + return 0;
> > +
> > +poweroff:
> > + ret = regulator_disable(innolux->supply);
> > + if (ret)
> > + return ret;
>
> I don't think we should be returning this error code. If we're here, it's
> because something else triggered err, and we should return that. Change this to:
>
> if (regulator_disable(innolux->supply))
> DRM_DEV_ERROR(panel->dev, "failed to disable regulator after error\n");
And maybe include the error code in that message still?
ret = regulator_disable(innolux->supply);
if (ret)
DRM_DEV_ERROR(panel->dev, "failed to disable regulator after error (%d)\n",
ret);
Brian
> > +
> > + gpiod_set_value_cansleep(innolux->enable_gpio, 0);
> > + return err;
> > +}
>
> <snip>
>
> > --
> > 2.6.3
_______________________________________________
dri-devel mailing list
dri-devel@xxxxxxxxxxxxxxxxxxxxx
https://lists.freedesktop.org/mailman/listinfo/dri-devel
