On 12/20/2016 03:55 AM, Rob Herring wrote:
On Wed, Dec 14, 2016 at 03:04:04PM +0900, Hoegeun Kwon wrote:
This patch add support for MIPI-DSI based S6E3HA2 AMOLED panel
driver. This panel has 1440x2560 resolution in 5.7-inch physical
panel in the TM2 device.
Signed-off-by: Donghwa Lee <dh09.lee@xxxxxxxxxxx>
Signed-off-by: Hyungwon Hwang <human.hwang@xxxxxxxxxxx>
Signed-off-by: Hoegeun Kwon <hoegeun.kwon@xxxxxxxxxxx>
---
.../bindings/display/panel/samsung,s6e3ha2.txt | 52 ++
drivers/gpu/drm/panel/Kconfig | 6 +
drivers/gpu/drm/panel/Makefile | 1 +
drivers/gpu/drm/panel/panel-samsung-s6e3ha2.c | 756 +++++++++++++++++++++
4 files changed, 815 insertions(+)
create mode 100644 Documentation/devicetree/bindings/display/panel/samsung,s6e3ha2.txt
create mode 100644 drivers/gpu/drm/panel/panel-samsung-s6e3ha2.c
diff --git a/Documentation/devicetree/bindings/display/panel/samsung,s6e3ha2.txt b/Documentation/devicetree/bindings/display/panel/samsung,s6e3ha2.txt
new file mode 100644
index 0000000..1f41f24
--- /dev/null
+++ b/Documentation/devicetree/bindings/display/panel/samsung,s6e3ha2.txt
@@ -0,0 +1,52 @@
+Samsung S6E3HA2 5.7" 1440x2560 AMOLED panel
+
+Required properties:
+ - compatible: "samsung,s6e3ha2"
+ - reg: the virtual channel number of a DSI peripheral
+ - vdd3-supply: core voltage supply
+ - vci-supply: voltage supply for analog circuits
+ - reset-gpios: a GPIO spec for the reset pin
+ - enable-gpios: a GPIO spec for the panel enable pin
+ - te-gpios: a GPIO spec for the tearing effect synchronization signal gpio pin
Need to specify the GPIOs as active high or low.
Hi Rob Herring,
Thanks for point out. I will add "(active high or low)" after the
description of the GPIOs.
+
+Optional properties:
+ - display-timings: timings for the connected panel as described by [1]
+
+The device node can contain one 'port' child node with one child
+'endpoint' node, according to the bindings defined in [2]. This
+node should describe panel's video bus.
+
+[1]: Documentation/devicetree/bindings/display/panel/display-timing.txt
+[2]: Documentation/devicetree/bindings/media/video-interfaces.txt
+
+Example:
+
+ panel@0 {
+ compatible = "samsung,s6e3ha2";
+ reg = <0>;
reg doesn't really work here unless this node is a child of the DSI
controller node. But if it is a child node, then you don't need the OF
graph.
The reg value is used in virtual child panel node so I think the reg
value is needed.
Please refer to the document below.
Documentation/devicetree/bindings/display/mipi-dsi-bus.txt
Best Regards,
Hoegeun Kwon
+ vdd3-supply = <&ldo27_reg>;
+ vci-supply = <&ldo28_reg>;
+ reset-gpios = <&gpg0 0 GPIO_ACTIVE_HIGH>;
+ enable-gpios = <&gpf1 5 GPIO_ACTIVE_HIGH>;
+ te-gpios = <&gpf1 3 GPIO_ACTIVE_HIGH>;
+
+ display-timings {
+ timing-0 {
+ clock-frequency = <0>;
+ hactive = <1440>;
+ vactive = <2560>;
+ hfront-porch = <1>;
+ hback-porch = <1>;
+ hsync-len = <1>;
+ vfront-porch = <1>;
+ vback-porch = <15>;
+ vsync-len = <1>;
+ };
+ };
+
+ port {
+ dsi_in: endpoint {
+ remote-endpoint = <&dsi_out>;
+ };
+ };
+ };
_______________________________________________
dri-devel mailing list
dri-devel@xxxxxxxxxxxxxxxxxxxxx
https://lists.freedesktop.org/mailman/listinfo/dri-devel
_______________________________________________
dri-devel mailing list
dri-devel@xxxxxxxxxxxxxxxxxxxxx
https://lists.freedesktop.org/mailman/listinfo/dri-devel
