Re: [PATCH RFC v3] drm: Add a new connector atomic property for link status

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Wed, Nov 23, 2016 at 11:28:21PM -0800, Manasi Navare wrote:
> This is RFC patch for adding a connector link-status property
> and making it atomic by adding it to the drm_connector_state.
> This is to make sure its wired properly in drm_atomic_connector_set_property
> and drm_atomic_connector_get_property functions.
> 
> v3:
> * Fixed a build error (Jani Saarinen)
> v2:
> * Removed connector->link_status (Daniel Vetter)
> * Set connector->state->link_status in drm_mode_connector_set_link_status_property
> (Daniel Vetter)
> * Set the connector_changed flag to true if connector->state->link_status changed.
> * Reset link_status to GOOD in update_output_state (Daniel Vetter)
> * Never allow userspace to set link status from Good To Bad (Daniel Vetter)
> 
> Cc: Jani Nikula <jani.nikula@xxxxxxxxxxxxxxx>
> Cc: Daniel Vetter <daniel.vetter@xxxxxxxxx>
> Cc: Ville Syrjala <ville.syrjala@xxxxxxxxxxxxxxx>
> Cc: Chris Wilson <chris@xxxxxxxxxxxxxxxxxx>
> Cc: Sean Paul <seanpaul@xxxxxxxxxxxx>

You lost all the acked-by from AMD about the link-status property. We need
those.

> Signed-off-by: Manasi Navare <manasi.d.navare@xxxxxxxxx>

Yeah I think this should work, but obviously testing has the final say.
Some nitpicks below, then it's r-b: me. But I think we also need to polish
the kernel-doc a bit more to address Sean Paul's questions.
-Daniel

> ---
>  drivers/gpu/drm/drm_atomic.c        | 10 ++++++
>  drivers/gpu/drm/drm_atomic_helper.c |  8 +++++
>  drivers/gpu/drm/drm_connector.c     | 61 ++++++++++++++++++++++++++++++++++++-
>  include/drm/drm_connector.h         | 18 ++++++++++-
>  include/drm/drm_mode_config.h       |  5 +++
>  include/uapi/drm/drm_mode.h         |  4 +++
>  6 files changed, 104 insertions(+), 2 deletions(-)
> 
> diff --git a/drivers/gpu/drm/drm_atomic.c b/drivers/gpu/drm/drm_atomic.c
> index 89737e4..990f013 100644
> --- a/drivers/gpu/drm/drm_atomic.c
> +++ b/drivers/gpu/drm/drm_atomic.c
> @@ -1087,6 +1087,14 @@ int drm_atomic_connector_set_property(struct drm_connector *connector,
>  		 * now?) atomic writes to DPMS property:
>  		 */
>  		return -EINVAL;
> +	} else if (property == config->link_status_property) {
> +		/* Never downgrade from GOOD to BAD on userspace's request here,
> +		 * only hw issues can do that.
> +		 */
> +		if (state->link_status == DRM_LINK_STATUS_GOOD)
> +			return 0;
> +		state->link_status = val;
> +		return 0;
>  	} else if (connector->funcs->atomic_set_property) {
>  		return connector->funcs->atomic_set_property(connector,
>  				state, property, val);
> @@ -1135,6 +1143,8 @@ static void drm_atomic_connector_print_state(struct drm_printer *p,
>  		*val = (state->crtc) ? state->crtc->base.id : 0;
>  	} else if (property == config->dpms_property) {
>  		*val = connector->dpms;
> +	} else if (property == config->link_status_property) {
> +		*val = state->link_status;
>  	} else if (connector->funcs->atomic_get_property) {
>  		return connector->funcs->atomic_get_property(connector,
>  				state, property, val);
> diff --git a/drivers/gpu/drm/drm_atomic_helper.c b/drivers/gpu/drm/drm_atomic_helper.c
> index 494680c..962ed66 100644
> --- a/drivers/gpu/drm/drm_atomic_helper.c
> +++ b/drivers/gpu/drm/drm_atomic_helper.c
> @@ -519,6 +519,13 @@ static int handle_conflicting_encoders(struct drm_atomic_state *state,
>  					       connector_state);
>  		if (ret)
>  			return ret;
> +		if (connector->state->crtc) {
> +			crtc_state = drm_atomic_get_existing_crtc_state(state,
> +									connector->state->crtc);
> +			if (connector->state->link_status !=
> +			    connector_state->link_status)
> +				crtc_state->connectors_changed = true;
> +		}

Why hide this here in handle_conflicting_encoders? This is a bit
confusing. I'd move it into the connector loop in
drm_atomic_helper_check_modeset().
>  	}
>  
>  	/*
> @@ -2258,6 +2265,7 @@ static int update_output_state(struct drm_atomic_state *state,
>  								NULL);
>  			if (ret)
>  				return ret;
> +			conn_state->link_status = DRM_LINK_STATUS_GOOD;
>  		}
>  	}
>  
> diff --git a/drivers/gpu/drm/drm_connector.c b/drivers/gpu/drm/drm_connector.c
> index 5a45262..cd53c39 100644
> --- a/drivers/gpu/drm/drm_connector.c
> +++ b/drivers/gpu/drm/drm_connector.c
> @@ -243,6 +243,10 @@ int drm_connector_init(struct drm_device *dev,
>  	drm_object_attach_property(&connector->base,
>  				      config->dpms_property, 0);
>  
> +	drm_object_attach_property(&connector->base,
> +				   config->link_status_property,
> +				   0);
> +
>  	if (drm_core_check_feature(dev, DRIVER_ATOMIC)) {
>  		drm_object_attach_property(&connector->base, config->prop_crtc_id, 0);
>  	}
> @@ -506,6 +510,12 @@ const char *drm_get_subpixel_order_name(enum subpixel_order order)
>  };
>  DRM_ENUM_NAME_FN(drm_get_dpms_name, drm_dpms_enum_list)
>  
> +static const struct drm_prop_enum_list drm_link_status_enum_list[] = {
> +	{ DRM_MODE_LINK_STATUS_GOOD, "Good" },
> +	{ DRM_MODE_LINK_STATUS_BAD, "Bad" },
> +};
> +DRM_ENUM_NAME_FN(drm_get_link_status_name, drm_link_status_enum_list)
> +
>  /**
>   * drm_display_info_set_bus_formats - set the supported bus formats
>   * @info: display info to store bus formats in
> @@ -625,7 +635,14 @@ int drm_display_info_set_bus_formats(struct drm_display_info *info,
>   * 	tiling and virtualize both &drm_crtc and &drm_plane if needed. Drivers
>   * 	should update this value using drm_mode_connector_set_tile_property().
>   * 	Userspace cannot change this property.
> - *
> + * link-status:
> + *      Connector link-status property to indicate the status of link during
> + *      the modeset. The default value of link-status is "GOOD". If something
> + *      fails during modeset, the kernel driver can set this to "BAD", prune
> + *      the mode list based on new link parameters and send a hotplug uevent
> + *      to notify userspace to re-check the valid modes through GET_CONNECTOR
> + *      IOCTL and redo a modeset. Drivers should update this value using
> + *      drm_mode_connector_set_link_status_property().

Please leave the empty line here after the definition list, for better
layout. Also I thought there were some comments from Sean Paul that the
kernel-doc was confusing, have you worked together with him to address
this?

>   * Connectors also have one standardized atomic property:
>   *
>   * CRTC_ID:
> @@ -666,6 +683,13 @@ int drm_connector_create_standard_properties(struct drm_device *dev)
>  		return -ENOMEM;
>  	dev->mode_config.tile_property = prop;
>  
> +	prop = drm_property_create_enum(dev, DRM_MODE_PROP_ATOMIC, "link-status",
> +					drm_link_status_enum_list,
> +					ARRAY_SIZE(drm_link_status_enum_list));
> +	if (!prop)
> +		return -ENOMEM;
> +	dev->mode_config.link_status_property = prop;
> +
>  	return 0;
>  }
>  
> @@ -995,6 +1019,41 @@ int drm_mode_connector_update_edid_property(struct drm_connector *connector,
>  }
>  EXPORT_SYMBOL(drm_mode_connector_update_edid_property);
>  
> +/**
> + * drm_mode_connector_set_link_status_property - Set link status property of a connector
> + * @connector: drm connector
> + * @link_status: new value of link status property (0: Good, 1: Bad)
> + *
> + * In usual working scenario, this link status property will always be set to
> + * "GOOD". If something fails during or after a mode set, the kernel driver should
> + * set this link status property to "BAD" and prune the mode list based on new
> + * information. The caller then needs to send a hotplug uevent for userspace to
> + *  re-check the valid modes through GET_CONNECTOR_IOCTL and retry modeset.
> + *
> + * Note that a lot of existing userspace do not handle this property.
> + * Drivers can therefore not rely on userspace to fix up everything and
> + * should try to handle issues (like just re-training a link) without
> + * userspace's intervention. This should only be used when the current mode
> + * fails and userspace must select a different display mode.
> + * The DRM driver can chose to not modify property and keep link status
> + * as "GOOD" always to keep the user experience same as it currently is.
> + *
> + * The reason for adding this property is to handle link training failures, but
> + * it is not limited to DP or link training. For example, if we implement
> + * asynchronous setcrtc, this property can be used to report any failures in that.
> + */
> +void drm_mode_connector_set_link_status_property(struct drm_connector *connector,
> +						 uint64_t link_status)
> +{
> +	struct drm_device *dev = connector->dev;
> +
> +	drm_modeset_lock(&dev->mode_config.connection_mutex, NULL);
> +	connector->state->link_status = link_status;
> +	drm_modeset_unlock(&dev->mode_config.connection_mutex);
> +
> +}
> +EXPORT_SYMBOL(drm_mode_connector_set_link_status_property);
> +
>  int drm_mode_connector_set_obj_prop(struct drm_mode_object *obj,
>  				    struct drm_property *property,
>  				    uint64_t value)
> diff --git a/include/drm/drm_connector.h b/include/drm/drm_connector.h
> index 34f9741..ba22ed1 100644
> --- a/include/drm/drm_connector.h
> +++ b/include/drm/drm_connector.h
> @@ -90,6 +90,17 @@ enum subpixel_order {
>  };
>  
>  /**
> + * enum drm_link_status - connector's link_status property value
> + *
> + * This enum is used as the connector's link status property value.
> + * It is set to the values defined in uapi.
> + */
> +enum drm_link_status {
> +	DRM_LINK_STATUS_GOOD = DRM_MODE_LINK_STATUS_GOOD,
> +	DRM_LINK_STATUS_BAD = DRM_MODE_LINK_STATUS_BAD,
> +};
> +
> +/**
>   * struct drm_display_info - runtime data about the connected sink
>   *
>   * Describes a given display (e.g. CRT or flat panel) and its limitations. For
> @@ -213,6 +224,9 @@ struct drm_connector_state {
>  
>  	struct drm_encoder *best_encoder;
>  
> +	/* Connector Link status */
> +	enum drm_link_status link_status;

make htmldocs should complain about the missing kernel-doc here. Just
convert your inline comment into a proper kernel-doc:

	/**
	 * @link_status: Connector link status
	 */

Also in general a comment that literally says the same as the code isn't
useful. Comments should explain why the code does something, not what
exactly it does - that should be self-evident.
> +
>  	struct drm_atomic_state *state;
>  };
>  
> @@ -695,6 +709,7 @@ struct drm_connector {
>  	uint8_t num_h_tile, num_v_tile;
>  	uint8_t tile_h_loc, tile_v_loc;
>  	uint16_t tile_h_size, tile_v_size;
> +

Spurious whitespace change, pls check for these before submitting. I think
this one here is new.

>  };
>  
>  #define obj_to_connector(x) container_of(x, struct drm_connector, base)
> @@ -767,12 +782,13 @@ int drm_mode_create_tv_properties(struct drm_device *dev,
>  int drm_mode_create_scaling_mode_property(struct drm_device *dev);
>  int drm_mode_create_aspect_ratio_property(struct drm_device *dev);
>  int drm_mode_create_suggested_offset_properties(struct drm_device *dev);
> -

Same.

>  int drm_mode_connector_set_path_property(struct drm_connector *connector,
>  					 const char *path);
>  int drm_mode_connector_set_tile_property(struct drm_connector *connector);
>  int drm_mode_connector_update_edid_property(struct drm_connector *connector,
>  					    const struct edid *edid);
> +void drm_mode_connector_set_link_status_property(struct drm_connector *connector,
> +						 uint64_t link_status);
>  
>  /**
>   * struct drm_tile_group - Tile group metadata
> diff --git a/include/drm/drm_mode_config.h b/include/drm/drm_mode_config.h
> index bf9991b..86faee4 100644
> --- a/include/drm/drm_mode_config.h
> +++ b/include/drm/drm_mode_config.h
> @@ -431,6 +431,11 @@ struct drm_mode_config {
>  	 */
>  	struct drm_property *tile_property;
>  	/**
> +	 * @link_status_property: Default connector property for link status
> +	 * of a connector
> +	 */
> +	struct drm_property *link_status_property;
> +	/**
>  	 * @plane_type_property: Default plane property to differentiate
>  	 * CURSOR, PRIMARY and OVERLAY legacy uses of planes.
>  	 */
> diff --git a/include/uapi/drm/drm_mode.h b/include/uapi/drm/drm_mode.h
> index 728790b..309c478 100644
> --- a/include/uapi/drm/drm_mode.h
> +++ b/include/uapi/drm/drm_mode.h
> @@ -123,6 +123,10 @@
>  #define DRM_MODE_DIRTY_ON       1
>  #define DRM_MODE_DIRTY_ANNOTATE 2
>  
> +/* Link Status options */
> +#define DRM_MODE_LINK_STATUS_GOOD	0
> +#define DRM_MODE_LINK_STATUS_BAD	1
> +
>  struct drm_mode_modeinfo {
>  	__u32 clock;
>  	__u16 hdisplay;
> -- 
> 1.9.1
> 
> _______________________________________________
> dri-devel mailing list
> dri-devel@xxxxxxxxxxxxxxxxxxxxx
> https://lists.freedesktop.org/mailman/listinfo/dri-devel

-- 
Daniel Vetter
Software Engineer, Intel Corporation
http://blog.ffwll.ch
_______________________________________________
dri-devel mailing list
dri-devel@xxxxxxxxxxxxxxxxxxxxx
https://lists.freedesktop.org/mailman/listinfo/dri-devel




[Index of Archives]     [Linux DRI Users]     [Linux Intel Graphics]     [Linux USB Devel]     [Video for Linux]     [Linux Audio Users]     [Yosemite News]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Linux USB Devel]     [Video for Linux]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]
  Powered by Linux