Hi,
On Fri, Oct 21, 2016 at 4:36 PM, Jean-Francois Moine <moinejf@xxxxxxx> wrote:
> This patch adds I2S support to sun8i SoCs as the A83T and H3.
>
> Signed-off-by: Jean-Francois Moine <moinejf@xxxxxxx>
> ---
> Note: This driver is closed to the sun4i-i2s except that:
> - it handles the H3
If it's close to sun4i-i2s, you should probably rework that one to support
the newer SoCs.
> - it creates the sound card (with sun4i-i2s, the sound card is created
> by the CODECs)
I think this is wrong. I2S is only the DAI. You typically have a separate
platform driver for the whole card, or just use simple-card.
> ---
> .../devicetree/bindings/sound/sun4i-i2s.txt | 38 +-
> sound/soc/sunxi/Kconfig | 8 +
> sound/soc/sunxi/Makefile | 3 +
> sound/soc/sunxi/sun8i-i2s.c | 700 +++++++++++++++++++++
> 4 files changed, 744 insertions(+), 5 deletions(-)
> create mode 100644 sound/soc/sunxi/sun8i-i2s.c
>
> diff --git a/Documentation/devicetree/bindings/sound/sun4i-i2s.txt b/Documentation/devicetree/bindings/sound/sun4i-i2s.txt
> index 7b526ec..2fb0a7a 100644
> --- a/Documentation/devicetree/bindings/sound/sun4i-i2s.txt
> +++ b/Documentation/devicetree/bindings/sound/sun4i-i2s.txt
> @@ -1,4 +1,4 @@
> -* Allwinner A10 I2S controller
> +* Allwinner A10/A38T/H3 I2S controller
>
> The I2S bus (Inter-IC sound bus) is a serial link for digital
> audio data transfer between devices in the system.
> @@ -6,20 +6,30 @@ audio data transfer between devices in the system.
> Required properties:
>
> - compatible: should be one of the followings
> - - "allwinner,sun4i-a10-i2s"
> + - "allwinner,sun4i-a10-i2s"
> + "allwinner,sun8i-a83t-i2s"
> + "allwinner,sun8i-h3-i2s"
> - reg: physical base address of the controller and length of memory mapped
> region.
> -- interrupts: should contain the I2S interrupt.
> - dmas: DMA specifiers for tx and rx dma. See the DMA client binding,
> Documentation/devicetree/bindings/dma/dma.txt
> -- dma-names: should include "tx" and "rx".
> +- dma-names: must include "tx" and/or "rx".
> - clocks: a list of phandle + clock-specifer pairs, one for each entry in clock-names.
> - clock-names: should contain followings:
> - "apb" : clock for the I2S bus interface
> - "mod" : module clock for the I2S controller
> - #sound-dai-cells : Must be equal to 0
>
> -Example:
> +Optional properties:
> +
> +- interrupts: I2S interrupt
> +- resets: phandle to the reset of the device
> +
> +Required nodes:
> +
> + - port: link to the associated CODEC (DAC, HDMI...)
Note here you are changing an existing binding, adding a required node.
If it were truely different, you probably should've started a new binding.
Regards
ChenYu
> +
> +Example 1:
>
> i2s0: i2s@01c22400 {
> #sound-dai-cells = <0>;
> @@ -32,3 +42,21 @@ i2s0: i2s@01c22400 {
> <&dma SUN4I_DMA_NORMAL 3>;
> dma-names = "rx", "tx";
> };
> +
> +Example 2:
> +
> +i2s2: i2s@1c22800 {
> + compatible = "allwinner,sun8i-a83t-i2s";
> + reg = <0x01c22800 0x60>;
> + clocks = <&ccu CLK_BUS_I2S2>, <&ccu CLK_I2S2>;
> + clock-names = "apb", "mod";
> + resets = <&ccu RST_I2S2>;
> + dmas = <&dma 27>;
> + dma-names = "tx";
> + status = "disabled";
> + port {
> + i2s2_hdmi: endpoint {
> + remote-endpoint = <&hdmi_i2s2>;
> + };
> + };
> +};
_______________________________________________
dri-devel mailing list
dri-devel@xxxxxxxxxxxxxxxxxxxxx
https://lists.freedesktop.org/mailman/listinfo/dri-devel
