On 10/13/2016 10:18 PM, Rob Clark wrote:
If the bottom-most layer is not fullscreen, we need to use the BASE
mixer stage for solid fill (ie. MDP5_CTL_BLEND_OP_FLAG_BORDER_OUT). The
blend_setup() code pretty much handled this already, we just had to
figure this out in _atomic_check() and assign the stages appropriately.
The patch looks good. I couldn't test the problematic scenario since I
don't have an easy way to reproduce it, but it doesn't break regular
usage (where base layer is full screen).
Reviewed-by: Archit Taneja <architt@xxxxxxxxxxxxxx>
Signed-off-by: Rob Clark <robdclark@xxxxxxxxx>
---
TODO mdp4 might need similar treatment?
drivers/gpu/drm/msm/mdp/mdp5/mdp5_crtc.c | 44 ++++++++++++++++++++------------
1 file changed, 27 insertions(+), 17 deletions(-)
diff --git a/drivers/gpu/drm/msm/mdp/mdp5/mdp5_crtc.c b/drivers/gpu/drm/msm/mdp/mdp5/mdp5_crtc.c
index fa2be7c..e42f62d 100644
--- a/drivers/gpu/drm/msm/mdp/mdp5/mdp5_crtc.c
+++ b/drivers/gpu/drm/msm/mdp/mdp5/mdp5_crtc.c
@@ -223,11 +223,6 @@ static void blend_setup(struct drm_crtc *crtc)
plane_cnt++;
}
- /*
- * If there is no base layer, enable border color.
- * Although it's not possbile in current blend logic,
- * put it here as a reminder.
- */
if (!pstates[STAGE_BASE] && plane_cnt) {
ctl_blend_flags |= MDP5_CTL_BLEND_OP_FLAG_BORDER_OUT;
DBG("Border Color is enabled");
@@ -365,6 +360,15 @@ static int pstate_cmp(const void *a, const void *b)
return pa->state->zpos - pb->state->zpos;
}
+/* is there a helper for this? */
+static bool is_fullscreen(struct drm_crtc_state *cstate,
+ struct drm_plane_state *pstate)
+{
+ return (pstate->crtc_x == 0) && (pstate->crtc_y == 0) &&
+ (pstate->crtc_w == cstate->mode.hdisplay) &&
+ (pstate->crtc_h == cstate->mode.vdisplay);
+}
+
static int mdp5_crtc_atomic_check(struct drm_crtc *crtc,
struct drm_crtc_state *state)
{
@@ -375,21 +379,11 @@ static int mdp5_crtc_atomic_check(struct drm_crtc *crtc,
struct plane_state pstates[STAGE_MAX + 1];
const struct mdp5_cfg_hw *hw_cfg;
const struct drm_plane_state *pstate;
- int cnt = 0, i;
+ int cnt = 0, base = 0, i;
DBG("%s: check", mdp5_crtc->name);
- /* verify that there are not too many planes attached to crtc
- * and that we don't have conflicting mixer stages:
- */
- hw_cfg = mdp5_cfg_get_hw_config(mdp5_kms->cfg);
drm_atomic_crtc_state_for_each_plane_state(plane, pstate, state) {
- if (cnt >= (hw_cfg->lm.nb_stages)) {
- dev_err(dev->dev, "too many planes!\n");
- return -EINVAL;
- }
-
-
pstates[cnt].plane = plane;
pstates[cnt].state = to_mdp5_plane_state(pstate);
@@ -399,8 +393,24 @@ static int mdp5_crtc_atomic_check(struct drm_crtc *crtc,
/* assign a stage based on sorted zpos property */
sort(pstates, cnt, sizeof(pstates[0]), pstate_cmp, NULL);
+ /* if the bottom-most layer is not fullscreen, we need to use
+ * it for solid-color:
+ */
+ if (!is_fullscreen(state, &pstates[0].state->base))
+ base++;
+
+ /* verify that there are not too many planes attached to crtc
+ * and that we don't have conflicting mixer stages:
+ */
+ hw_cfg = mdp5_cfg_get_hw_config(mdp5_kms->cfg);
+
+ if ((cnt + base) >= hw_cfg->lm.nb_stages) {
+ dev_err(dev->dev, "too many planes!\n");
+ return -EINVAL;
+ }
+
for (i = 0; i < cnt; i++) {
- pstates[i].state->stage = STAGE_BASE + i;
+ pstates[i].state->stage = STAGE_BASE + i + base;
DBG("%s: assign pipe %s on stage=%d", mdp5_crtc->name,
pipe2name(mdp5_plane_pipe(pstates[i].plane)),
pstates[i].state->stage);
--
Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum,
a Linux Foundation Collaborative Project
_______________________________________________
dri-devel mailing list
dri-devel@xxxxxxxxxxxxxxxxxxxxx
https://lists.freedesktop.org/mailman/listinfo/dri-devel
