Regards,
vinay simha
On Thu, Sep 8, 2016 at 5:02 AM, John Stultz <john.stultz@xxxxxxxxxx> wrote:
> Tagging on to Archit's patchset here.
>
> Add DSI and panel nodes to get graphics up and running
> on the Nexus7.
>
> This still depends on the panel driver being present
> (currently under review) along with the rpmclk code.
>
> Feedback would be appreciated here!
>
> Cc: Archit Taneja <architt@xxxxxxxxxxxxxx>
> Cc: vinay simha <vinaysimha@xxxxxxxxxxxxxxxxxxxx>
> Cc: andy.gross@xxxxxxxxxx
> Cc: robdclark@xxxxxxxxx
> Cc: linux-arm-msm@xxxxxxxxxxxxxxx
> Cc: dri-devel@xxxxxxxxxxxxxxxxxxxxx
> Signed-off-by: John Stultz <john.stultz@xxxxxxxxxx>
> ---
> arch/arm/boot/dts/qcom-apq8064-asus-nexus7-flo.dts | 78 +++++++++++++++++++++-
> 1 file changed, 76 insertions(+), 2 deletions(-)
>
> diff --git a/arch/arm/boot/dts/qcom-apq8064-asus-nexus7-flo.dts b/arch/arm/boot/dts/qcom-apq8064-asus-nexus7-flo.dts
> index ff856c3..e25a764 100644
> --- a/arch/arm/boot/dts/qcom-apq8064-asus-nexus7-flo.dts
> +++ b/arch/arm/boot/dts/qcom-apq8064-asus-nexus7-flo.dts
> @@ -27,6 +27,18 @@
> regulator-boot-on;
> };
>
> + vcc_1p8v: regulator-fixed@2 {
> + compatible = "regulator-fixed";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-name = "vcc_1p8v";
> + regulator-type = "voltage";
> + startup-delay-us = <0>;
> + gpio = <&pm8921_gpio 23 GPIO_ACTIVE_HIGH>;
> + enable-active-high;
> + regulator-boot-on;
> + };
> +
We can remove the vcc_1p8v, some modification had done in the panel tree
> gpio-keys {
> compatible = "gpio-keys";
> volume_up {
> @@ -99,6 +111,7 @@
> l2 {
> regulator-min-microvolt = <1200000>;
> regulator-max-microvolt = <1200000>;
> + regulator-always-on;
> };
>
> /* msm_otg-HSUSB_3p3 */
> @@ -133,13 +146,14 @@
> regulator-min-microvolt = <3000000>;
> regulator-max-microvolt = <3000000>;
> bias-pull-down;
> + regulator-always-on;
> };
>
> /* pwm_power for backlight */
> l17 {
> regulator-min-microvolt = <3000000>;
> - regulator-max-microvolt = <3600000>;
> - bias-pull-down;
> + regulator-max-microvolt = <3000000>;
> + regulator-always-on;
> };
>
> /* camera, qdsp6 */
> @@ -184,6 +198,66 @@
> };
> };
>
> + mdp@5100000 {
> + status = "okay";
> + ports {
> + port@1 {
> + mdp_dsi1_out: endpoint {
> + remote-endpoint = <&dsi0_in>;
> + };
> + };
> + };
> + };
> +
> + dsi0: qcom,mdss_dsi@4700000 {
> + status = "okay";
> + vdda-supply = <&pm8921_l2>;/*VDD_MIPI1 to 4*/
> + vdd-supply = <&pm8921_l8>;
> + vddio-supply = <&pm8921_lvs7>;
> + avdd-supply = <&pm8921_l11>;
> + vcss-supply = <&ext_3p3v>;
> +
> + panel@0 {
> + reg = <0>;
> + compatible = "jdi,lt070me05000";
> +
> + pinctrl-names = "default";
> + pinctrl-0 = <&dsi_panel_pinctrl>;
> +
> + vddp-supply = <&pm8921_l17>;
> + dcdc_en-supply = <&pm8921_lvs7>;
> + vcc-supply = <&vcc_1p8v>;
> +
> + reset-gpios = <&tlmm_pinmux 54 0>;
> + enable-gpios = <&pm8921_gpio 36 GPIO_ACTIVE_HIGH>;
> +
We can remove the pinctrl-names and pinctrl-0, have the below contents
lilke this
panel@0 {
compatible = "jdi,lt070me05000";
reg = <0>;
vddp-supply = <&pm8921_l17>;
iovcc-supply = <&pm8921_lvs7>;
enable-gpios = <&pm8921_gpio 36 GPIO_ACTIVE_HIGH>;
reset-gpios = <&tlmm_pinmux 54 GPIO_ACTIVE_LOW>;
dcdc-en-gpios = <&pm8921_gpio 23 GPIO_ACTIVE_HIGH>;
> + port {
> + panel_in: endpoint {
> + remote-endpoint = <&dsi0_out>;
> + };
> + };
> + };
> + ports {
> + port@0 {
> + dsi0_in: endpoint {
> + remote-endpoint = <&mdp_dsi1_out>;
> + };
> + };
> +
> + port@1 {
> + dsi0_out: endpoint {
> + remote-endpoint = <&panel_in>;
> + data-lanes = <0 1 2 3>;
> + };
> + };
> + };
> + };
> +
> + mdp_dsi_phy0: qcom,mdss_dsi_phy@4700200 {
> + status = "okay";
> + vddio-supply = <&pm8921_lvs7>;/*VDD_PLL2_1 to 7*/
> + };
> +
> gsbi@16200000 {
> status = "okay";
> qcom,mode = <GSBI_PROT_I2C>;
> --
> 1.9.1
>
_______________________________________________
dri-devel mailing list
dri-devel@xxxxxxxxxxxxxxxxxxxxx
https://lists.freedesktop.org/mailman/listinfo/dri-devel
