Re: Kernel Freeze with American Megatrends BIOS

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On 30 August 2016 at 18:37, Roland Singer <roland.singer@xxxxxxxxxxxxx> wrote:
> I am running 4.7.2, but I also just tried the 4.8.0-rc4 mainline kernel.
> The result is the same. There is no difference if bbswitch of acpi_call
> is used. However I noticed following:
>
> 1. The nouveau driver is broken in both kernel version and is responsible
>    for the freezes while gathering power state information with bbswitch.
>    Sometimes while shutting the system down, everything except the LCD
>    screen is switched off. This only happens with nouveau.
>    I noticed following error log messages:
>
I second Ilia here. Using bbswitch in conjunction with any driver (be
that nouveau or the proprietary one) is a bad idea.

>    kernel: nouveau 0000:01:00.0: fb: 6144 MiB GDDR5
>    kernel: nouveau 0000:01:00.0: priv: HUB0: 10ecc0 ffffffff (1e40822c)
>    kernel: nouveau 0000:01:00.0: DRM: VRAM: 6144 MiB
>    kernel: nouveau 0000:01:00.0: DRM: GART: 1048576 MiB
>    kernel: nouveau 0000:01:00.0: DRM: Pointer to TMDS table invalid
>    kernel: nouveau 0000:01:00.0: DRM: DCB version 4.1
>    kernel: nouveau 0000:01:00.0: DRM: Pointer to flat panel table invalid
>
> 2. -> Boot with nouveau module loaded
>    -> switch off the discrete GPU with bbswitch or acpi_call
>    -> start X11
>    -> obtaining power state with bbswitch freezes the system
>    -> or working with the system for some minutes freezes the system
>
(If Ilia's suggestions does not help) Confirm if the freeze is due
to/as the GPU is powered on or off.

> 3. -> Boot with nouveau module blacklisted
>    -> switch off the discrete GPU
>    -> start X11
>    -> system immediately freezes
>
It's perfectly possible that the discrete GPU is set as boot one and X
goes angry since there's no driver/way to bring it up.

> 4. -> Boot with nouveau module blacklisted
>    -> switch off the discrete GPU
>    -> start Wayland
>    -> system runs - Note: I tried this for couple of days with 4.6 and 4.7 mainline
>                           and the system freezed randomly after some time.
>                           However I have to test if this is still present with 4.7.2
>                           and 4.8 mainline. Right now it seams to be fine.
>    -> running Xwayland (does not depend on the GPU power state) kills performance!
>       the system freezes for several seconds...
>       So working with Wayland is also no solution.
>
> My conclusion:
>
> 1. Nouveau has couple of problems with GTX 9** M Nvidia GPUs.
>    I would love to help here.
>
> 2. X11 is just broken and is not capable to start the graphical session
>    if the nvidia GPU is not handled by any video driver (kernel module).
>    Even forcing X11 to ignore the discrete GPU doesn't help.
>
Out of curiosity: how did you force X to ignore the device ?

>    Setting the command line arguments to:
>
>      acpi_osi=! acpi_osi="Windows 2009"
>
>    fixes the issues with X11 but other things break...
>    What the hell is going on?! :/
>
You can check if it's the boot_vga assumption with

Check wh

You're a victum of the Windows specific fun (quirks?) in

> Am 30.08.2016 um 17:48 schrieb Emil Velikov:
>> On 30 August 2016 at 16:25, Roland Singer <roland.singer@xxxxxxxxxxxxx> wrote:
>>> I tried these scenarios:
>>>
>>> 1. Booted the system without the bbswitch module. The nouveau module
>>>    was loaded and is responsible for the power management of the GPU.
>>>    The graphical session freezes after some minutes...
>>>
>>> 2. Booted the system without bbswitch and with nouveau blacklisted.
>>>    Manually loaded bbswitch to switch off the discrete GPU.
>>>    Same freeze after a while or by explicitly obtaining the GPU state.
>>>
>>> Is there a possibility to switch off the discrete card without bbswitch?
>>> If this is possible, then I could test this without nouveau and bbswitch
>>> at all. If the system hangs, then it is not the video driver nor bbswitch.
>>>
>> As Ilia mentioned acpi_call should do it. You can also check with the
>> nouveau/bbwswitch code to see which ones they use in your case and
>> bash it manually. It might be that the 'wrong one' gets used thus
>> things going horribly wrong.
>>
>> Regards,
>> Emil
>>
>
_______________________________________________
dri-devel mailing list
dri-devel@xxxxxxxxxxxxxxxxxxxxx
https://lists.freedesktop.org/mailman/listinfo/dri-devel




[Index of Archives]     [Linux DRI Users]     [Linux Intel Graphics]     [Linux USB Devel]     [Video for Linux]     [Linux Audio Users]     [Yosemite News]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Linux USB Devel]     [Video for Linux]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]
  Powered by Linux