On Wed, 04 May 2016, "Prosyak, Vitaly" <Vitaly.Prosyak@xxxxxxx> wrote: > We are going to use min/max vertical refresh rate when enter/exit to > the dynamic refresh rate mode ,it is known as 'freesync', enter/exit > to full screen games. As Daniel said, we should see the patch using them too. It's hard to say whether this is the right thing to do otherwise. BR, Jani. > Right , we may have a helper function which extracts these properties and store wherever need it. > But this an alternative solution with additional helper adds some code duplication into drm_edid.c since the case already present in the code: > case 0x01: /* just the ranges, no formula */ Also these values are parsed during each mode enumeration. > > Why I put into connector: > Drm connector have already similar items from EDID: drm_tile_group ,etc... > > Vitaly > -----Original Message-----. > > From: Daniel Vetter [mailto:daniel.vetter@xxxxxxxx] On Behalf Of Daniel Vetter > Sent: Tuesday, May 03, 2016 4:24 PM > To: Prosyak, Vitaly > Cc: dri-devel@xxxxxxxxxxxxxxxxxxxxx > Subject: Re: [PATCH] drm/edid : cache edid range limits in drm connector > > On Tue, May 03, 2016 at 11:05:24AM -0400, Vitaly Prosyak wrote: >> Cache in drm connector the edid range limits properties: >> min/max vertical refresh rates and max pixel clock. >> It would be used when enter to drr mode. >> >> Signed-off-by: Vitaly Prosyak <vitaly.prosyak@xxxxxxx> > > Where's the patches that will use this? It might make sense to instead have some helper functions to compute these values, so that drivers can store them wherever they want/need. But impossible to tell without the users of this stuff. > -Daniel > >> --- >> drivers/gpu/drm/drm_edid.c | 11 +++++++++++ >> include/drm/drm_crtc.h | 5 +++++ >> 2 files changed, 16 insertions(+) >> >> diff --git a/drivers/gpu/drm/drm_edid.c b/drivers/gpu/drm/drm_edid.c >> index 04cb487..7e49962 100644 >> --- a/drivers/gpu/drm/drm_edid.c >> +++ b/drivers/gpu/drm/drm_edid.c >> @@ -2190,6 +2190,17 @@ do_inferred_modes(struct detailed_timing *timing, void *c) >> timing); >> break; >> case 0x01: /* just the ranges, no formula */ >> + closure->connector->min_vfreq = range->min_vfreq; >> + closure->connector->max_vfreq = range->max_vfreq; >> + if (closure->edid->revision >= 4) { >> + if ((range->flags & 0x03) == 0x3) >> + closure->connector->min_vfreq += 255; >> + if (range->flags & 0x02) >> + closure->connector->max_vfreq += 255; >> + } >> + closure->connector->max_pixel_clock_khz = >> + range_pixel_clock(closure->edid, (u8 *)timing); >> + break; >> default: >> break; >> } >> diff --git a/include/drm/drm_crtc.h b/include/drm/drm_crtc.h index >> c5b4b81..85fc554 100644 >> --- a/include/drm/drm_crtc.h >> +++ b/include/drm/drm_crtc.h >> @@ -1230,6 +1230,11 @@ struct drm_connector { >> uint8_t num_h_tile, num_v_tile; >> uint8_t tile_h_loc, tile_v_loc; >> uint16_t tile_h_size, tile_v_size; >> + >> + /*EDID range limits for drr*/ >> + int min_vfreq ; >> + int max_vfreq ; >> + int max_pixel_clock_khz; >> }; >> >> /** >> -- >> 1.9.1 >> >> _______________________________________________ >> dri-devel mailing list >> dri-devel@xxxxxxxxxxxxxxxxxxxxx >> https://lists.freedesktop.org/mailman/listinfo/dri-devel > > -- > Daniel Vetter > Software Engineer, Intel Corporation > http://blog.ffwll.ch > _______________________________________________ > dri-devel mailing list > dri-devel@xxxxxxxxxxxxxxxxxxxxx > https://lists.freedesktop.org/mailman/listinfo/dri-devel -- Jani Nikula, Intel Open Source Technology Center _______________________________________________ dri-devel mailing list dri-devel@xxxxxxxxxxxxxxxxxxxxx https://lists.freedesktop.org/mailman/listinfo/dri-devel
