Hi Bjorn, Rob,
On 04/19/2016 11:14 PM, Rob Clark wrote:
On Apr 19, 2016 11:50, "Bjorn Andersson" <bjorn.andersson@xxxxxxxxxx
<mailto:bjorn.andersson@xxxxxxxxxx>> wrote:
>
> On Tue 19 Apr 03:56 PDT 2016, Archit Taneja wrote:
>
> > Calling the legacy gpio_free on an invalid GPIO (a GPIO numbered -1)
> > results in kernel warnings. This causes a lot of backtraces when
> > we try to unload the drm/msm module.
> >
> > Call gpio_free only on valid GPIOs.
> >
> > Signed-off-by: Archit Taneja <architt@xxxxxxxxxxxxxx
<mailto:architt@xxxxxxxxxxxxxx>>
> > ---
> > drivers/gpu/drm/msm/hdmi/hdmi_connector.c | 19 ++++++++++++-------
> > 1 file changed, 12 insertions(+), 7 deletions(-)
> >
> > diff --git a/drivers/gpu/drm/msm/hdmi/hdmi_connector.c
b/drivers/gpu/drm/msm/hdmi/hdmi_connector.c
> > index 26129bf..ce86117 100644
> > --- a/drivers/gpu/drm/msm/hdmi/hdmi_connector.c
> > +++ b/drivers/gpu/drm/msm/hdmi/hdmi_connector.c
> > @@ -112,13 +112,16 @@ static int gpio_config(struct hdmi *hdmi,
bool on)
> > for (i = 0; i < HDMI_MAX_NUM_GPIO; i++) {
> > struct hdmi_gpio_data gpio = config->gpios[i];
> >
> > - if (gpio.output) {
> > - int value = gpio.value ? 0 : 1;
> > + if (gpio.num != -1) {
> > + if (gpio.output) {
> > + int value = gpio.value ? 0 : 1;
> >
> > - gpio_set_value_cansleep(gpio.num, value);
> > - }
> > + gpio_set_value_cansleep(gpio.num,
> > + value);
> > + }
> >
> > - gpio_free(gpio.num);
> > + gpio_free(gpio.num);
> > + }
> > };
> >
> > DBG("gpio off");
> > @@ -126,8 +129,10 @@ static int gpio_config(struct hdmi *hdmi, bool on)
> >
> > return 0;
> > err:
> > - while (i--)
> > - gpio_free(config->gpios[i].num);
> > + while (i--) {
> > + if (config->gpios[i].num != -1)
> > + gpio_free(config->gpios[i].num);
> > + }
> >
> > return ret;
> > }
>
> The patch in itself looks good, but the bigger picture does not.
>
> The ddc and hdp should be muxed to the hdmi block, so they should not
> operated as gpios.
I agree on the DDC part. I am not sure why they are passed as GPIOs to
the driver. For boards that do this (i.e, 1fc6410), the pinctrl tlmm
node sets the GPIOs function as "hdmi". Does that mean the the
gpio_set_value() in the driver are simply ignored?
I'll test and drop these if things work fine without them.
>
> The mux seems more of a gpio so it should be made more explicit - i.e.
> actually support muxing (if that's needed) rather than just setting hard
> coded values.
I have to study the schematics a bit on what the MUX actually does.
Note that at least on some devices, hpd was unreliable without using a
combination of gpio and denounced hpd signal from HDMI block...
Hmm, one thing I don't get is that the pinctrl DT node for the HPD pin
explicitly assigns its function as "hdmi". If that's the case, how does
it even work as a gpio?
Not sure what sort of MUX it is but it seemed possible (and necessary)
to use both at same time..
Please be sure to test lots of devices and monitors if you are going to
change this ;-)
For sure!
BR,
-R
> And you should not gpio_request/free the gpio upon every usage, request
> it during "probe time" and release it during "remove".
The hpd_enable/disable functions actually get called only during probe
and remove. We don't enable/disable HPD sensing at other points in the
driver. So, I guess it should be okay for now.
Thanks,
Archit
--
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora
Forum, hosted by The Linux Foundation
_______________________________________________
dri-devel mailing list
dri-devel@xxxxxxxxxxxxxxxxxxxxx
https://lists.freedesktop.org/mailman/listinfo/dri-devel
