Rob Herring <robh@xxxxxxxxxx> writes: > On Fri, Mar 18, 2016 at 07:42:45PM -0700, Eric Anholt wrote: >> The DPI interface involves taking a ton of our GPIOs to be used as >> outputs, and routing display signals over them in parallel. >> >> Signed-off-by: Eric Anholt <eric@xxxxxxxxxx> >> --- >> .../devicetree/bindings/display/brcm,bcm-vc4.txt | 67 +++ >> drivers/gpu/drm/vc4/Kconfig | 1 + >> drivers/gpu/drm/vc4/Makefile | 1 + >> drivers/gpu/drm/vc4/vc4_debugfs.c | 1 + >> drivers/gpu/drm/vc4/vc4_dpi.c | 518 +++++++++++++++++++++ >> drivers/gpu/drm/vc4/vc4_drv.c | 1 + >> drivers/gpu/drm/vc4/vc4_drv.h | 5 + >> 7 files changed, 594 insertions(+) >> create mode 100644 drivers/gpu/drm/vc4/vc4_dpi.c >> >> diff --git a/Documentation/devicetree/bindings/display/brcm,bcm-vc4.txt b/Documentation/devicetree/bindings/display/brcm,bcm-vc4.txt >> index 56a961a..1782c3f 100644 >> --- a/Documentation/devicetree/bindings/display/brcm,bcm-vc4.txt >> +++ b/Documentation/devicetree/bindings/display/brcm,bcm-vc4.txt >> @@ -35,6 +35,44 @@ Optional properties for HDMI: >> as an interrupt/status bit in the HDMI controller >> itself). See bindings/pinctrl/brcm,bcm2835-gpio.txt >> >> +Required properties for DPI: >> +- compatible: Should be "brcm,bcm2835-dpi" >> +- reg: Physical base address and length of the registers >> +- clocks: a) core: The core clock the unit runs on >> + b) pixel: The pixel clock that feeds the pixelvalve >> +- port: Port node with a single endpoint connecting to the >> + panel device, as defined in [1] >> +- brcm,output-format: Output data format, must be one of: >> + 0) disabled >> + 1) 00000000rrrrrggggggbbbbb >> + 2) 000rrrrr00gggggg000bbbbb >> + 3) 00rrrrr000gggggg00bbbbb0 >> + 4) 000000rrrrrrggggggbbbbbb >> + 5) 00rrrrrr00gggggg00bbbbbb >> + 6) rrrrrrrrggggggggbbbbbbbb >> + >> +Optional properties for DPI: >> +- brcm,rgb-order: RGB reordering, must be one of: >> + 0) RGB >> + 1) BGR >> + 2) GRB >> + 3) BRG > >> +- brcm,hsync-disable: Disables the hsync signal >> +- brcm,vsync-disable: Disables the vsync signal >> +- brcm,output-enable-disable: Disables the output enable signal >> +- brcm,hsync-falling: Outputs the hsync signal on the falling clk edge >> +- brcm,vsync-falling: Outputs the vsync signal on the falling clk edge >> +- brcm,output-enable-falling: Outputs the output enable signal on the >> + falling clk edge >> +- brcm,output-enable-invert: Inverts the polarity of the output enable >> + signal >> +- brcm,pixel-clk-invert: Inverts the polarity of the pixel clk signal >> +- brcm,output-enable-mode: Sets output enable when (vsync | hsync) >> + instead of (hactive & vactive) > > These are all really properties of what the panel requires and we > already have video timings binding that would cover some of these. > > Also, do you have actual users? Some of these seem like they would be > rare or never. I've not seen panels caring about which clock edge the > sync signals are on. I was using output-format, rgb_order, output-enable-mode to get my panel to work. I'm suspicious that the !output_enable_mode is not useful, though (Note: I had documented it backwards: false is hsync|vsync, true is hactive&vactive). That just left me with output-format. I think .bus_format in the panel_desc can cover that, so I've now dropped all of these brcm properties.
Attachment:
signature.asc
Description: PGP signature
_______________________________________________ dri-devel mailing list dri-devel@xxxxxxxxxxxxxxxxxxxxx https://lists.freedesktop.org/mailman/listinfo/dri-devel
