Hi, Since 2.6.36-rc1 I have an oops when loading the nouveau driver. The system woks ok expect for the nouveau driver and the console gets corrupted :( I attach relevant informations in attached files : o dmesg output for 2.6.36-rc2-git1 o ksymoops output for the above file If you need more informations please let me know. If you want me to test patches let me know. If you want me to run a git bissect let me know. thanx for your help. Other relevant informations: Output of ver_linux : Linux flocon 2.6.36-rc2-git1 #81 SMP PREEMPT Mon Aug 23 15:14:05 CEST 2010 i686 GNU/Linux Gnu C 4.4.5 Gnu make 3.81 binutils 2.20.1 util-linux 2.17.2 mount support module-init-tools 3.12 e2fsprogs 1.41.12 jfsutils 1.1.12 xfsprogs 3.1.2 pcmciautils 015 Linux C Library 2.11.2 Dynamic linker (ldd) 2.11.2 Procps 3.2.8 Net-tools 1.60 Console-tools 0.2.3 Sh-utils 8.5 wireless-tools 30 Modules Loaded nfsd lockd nfs_acl auth_rpcgss sunrpc exportfs fuse snd_intel8x0 snd_ac97_codec nouveau ac97_bus snd_pcm_oss snd_mixer_oss snd_pcm ttm firewire_ohci snd_seq sg cb710_mmc uhci_hcd snd_timer firewire_core mmc_core drm_kms_helper sr_mod 8139too ehci_hcd snd_seq_device snd crc_itu_t usbcore cb710 ohci1394 cdrom 8139cp soundcore cfbcopyarea snd_page_alloc cfbimgblt ieee1394 intel_agp cfbfillrect battery ac btrfs crc32c libcrc32c sd_mod Output of lspci : 00:00.0 Host bridge: Intel Corporation 82865G/PE/P DRAM Controller/Host-Hub Interface (rev 02) Subsystem: Hewlett-Packard Company NX9500 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx- Latency: 0 Region 0: Memory at d8000000 (32-bit, prefetchable) [size=128M] Capabilities: [e4] Vendor Specific Information: Len=06 <?> Capabilities: [a0] AGP version 3.0 Status: RQ=32 Iso- ArqSz=2 Cal=2 SBA+ ITACoh- GART64- HTrans- 64bit- FW+ AGP3+ Rate=x4,x8 Command: RQ=1 ArqSz=0 Cal=2 SBA- AGP+ GART64- 64bit- FW- Rate=<none> Kernel driver in use: agpgart-intel 00:01.0 PCI bridge: Intel Corporation 82865G/PE/P PCI to AGP Controller (rev 02) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 96 Bus: primary=00, secondary=01, subordinate=01, sec-latency=80 I/O behind bridge: 0000f000-00000fff Memory behind bridge: d1000000-d1ffffff Prefetchable memory behind bridge: e0000000-efffffff Secondary status: 66MHz+ FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR- BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- 00:06.0 System peripheral: Intel Corporation 82865G/PE/P Processor to I/O Memory Interface (rev ff) (prog-if ff) !!! Unknown header type 7f 00:1d.0 USB Controller: Intel Corporation 82801EB/ER (ICH5/ICH5R) USB UHCI Controller #1 (rev 02) (prog-if 00 [UHCI]) Subsystem: Hewlett-Packard Company NX9500 Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 16 Region 4: I/O ports at 1cc0 [size=32] Kernel driver in use: uhci_hcd 00:1d.1 USB Controller: Intel Corporation 82801EB/ER (ICH5/ICH5R) USB UHCI Controller #2 (rev 02) (prog-if 00 [UHCI]) Subsystem: Hewlett-Packard Company NX9500 Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin B routed to IRQ 19 Region 4: I/O ports at 1ce0 [size=32] Kernel driver in use: uhci_hcd 00:1d.2 USB Controller: Intel Corporation 82801EB/ER (ICH5/ICH5R) USB UHCI Controller #3 (rev 02) (prog-if 00 [UHCI]) Subsystem: Hewlett-Packard Company NX9500 Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin C routed to IRQ 18 Region 4: I/O ports at 2000 [size=32] Kernel driver in use: uhci_hcd 00:1d.7 USB Controller: Intel Corporation 82801EB/ER (ICH5/ICH5R) USB2 EHCI Controller (rev 02) (prog-if 20 [EHCI]) Subsystem: Hewlett-Packard Company NX9500 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin D routed to IRQ 23 Region 0: Memory at d0000000 (32-bit, non-prefetchable) [size=1K] Capabilities: [50] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- Capabilities: [58] Debug port: BAR=1 offset=00a0 Kernel driver in use: ehci_hcd 00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev c2) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Bus: primary=00, secondary=02, subordinate=02, sec-latency=32 I/O behind bridge: 00003000-00003fff Memory behind bridge: d2000000-d23fffff Prefetchable memory behind bridge: 20000000-23ffffff Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR- BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- 00:1f.0 ISA bridge: Intel Corporation 82801EB/ER (ICH5/ICH5R) LPC Interface Bridge (rev 02) Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 00:1f.1 IDE interface: Intel Corporation 82801EB/ER (ICH5/ICH5R) IDE Controller (rev 02) (prog-if 8a [Master SecP PriP]) Subsystem: Hewlett-Packard Company NX9500 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 18 Region 0: I/O ports at 01f0 [size=8] Region 1: I/O ports at 03f4 [size=1] Region 2: I/O ports at 0170 [size=8] Region 3: I/O ports at 0374 [size=1] Region 4: I/O ports at 2040 [size=16] Region 5: Memory at 24000000 (32-bit, non-prefetchable) [size=1K] Kernel driver in use: ata_piix 00:1f.3 SMBus: Intel Corporation 82801EB/ER (ICH5/ICH5R) SMBus Controller (rev 02) Subsystem: Hewlett-Packard Company Device 006a Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Interrupt: pin B routed to IRQ 10 Region 4: I/O ports at 2020 [size=32] 00:1f.5 Multimedia audio controller: Intel Corporation 82801EB/ER (ICH5/ICH5R) AC'97 Audio Controller (rev 02) Subsystem: Hewlett-Packard Company NX9500 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin B routed to IRQ 17 Region 0: I/O ports at 1400 [size=256] Region 1: I/O ports at 1c80 [size=64] Region 2: Memory at d0000c00 (32-bit, non-prefetchable) [size=512] Region 3: Memory at d0000800 (32-bit, non-prefetchable) [size=256] Capabilities: [50] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- Kernel driver in use: Intel ICH 00:1f.6 Modem: Intel Corporation 82801EB/ER (ICH5/ICH5R) AC'97 Modem Controller (rev 02) (prog-if 00 [Generic]) Subsystem: Hewlett-Packard Company NX9500 Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin B routed to IRQ 10 Region 0: I/O ports at 1800 [size=256] Region 1: I/O ports at 1c00 [size=128] Capabilities: [50] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- 01:00.0 VGA compatible controller: nVidia Corporation NV31M [GeForce FX Go5600] (rev a1) (prog-if 00 [VGA controller]) Subsystem: Hewlett-Packard Company Device 006a Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 40 (1250ns min, 250ns max) Interrupt: pin A routed to IRQ 16 Region 0: Memory at d1000000 (32-bit, non-prefetchable) [size=16M] Region 1: Memory at e0000000 (32-bit, prefetchable) [size=256M] Expansion ROM at <unassigned> [disabled] Capabilities: [60] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- Capabilities: [44] AGP version 3.0 Status: RQ=32 Iso- ArqSz=0 Cal=3 SBA+ ITACoh- GART64- HTrans- 64bit- FW+ AGP3+ Rate=x4,x8 Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW- Rate=<none> Kernel driver in use: nouveau 02:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10) Subsystem: Hewlett-Packard Company NX9500 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 32 (8000ns min, 16000ns max) Interrupt: pin A routed to IRQ 20 Region 0: I/O ports at 3000 [size=256] Region 1: Memory at d2005800 (32-bit, non-prefetchable) [size=256] Capabilities: [50] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0-,D1+,D2+,D3hot+,D3cold+) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- Kernel driver in use: 8139too 02:01.0 CardBus bridge: ENE Technology Inc CB-710/2/4 Cardbus Controller (rev 02) Subsystem: Hewlett-Packard Company NX9500 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 32, Cache Line Size: 32 bytes Interrupt: pin A routed to IRQ 17 Region 0: Memory at d2004000 (32-bit, non-prefetchable) [size=4K] Bus: primary=02, secondary=03, subordinate=06, sec-latency=176 Memory window 0: 20000000-23fff000 (prefetchable) Memory window 1: 28000000-2bfff000 (prefetchable) I/O window 0: 00003400-000034ff I/O window 1: 00003800-000038ff BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt- PostWrite- 16-bit legacy interface ports at 0001 02:01.1 FLASH memory: ENE Technology Inc CB710 Memory Card Reader Controller Subsystem: Hewlett-Packard Company NX9500 Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Interrupt: pin B routed to IRQ 18 Region 0: I/O ports at 3c00 [size=128] Capabilities: [a0] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- Kernel driver in use: cb710 02:02.0 FireWire (IEEE 1394): Texas Instruments TSB43AB21 IEEE-1394a-2000 Controller (PHY/Link) (prog-if 10 [OHCI]) Subsystem: Hewlett-Packard Company NX9500 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 32 (500ns min, 1000ns max), Cache Line Size: 32 bytes Interrupt: pin A routed to IRQ 19 Region 0: Memory at d2005000 (32-bit, non-prefetchable) [size=2K] Region 1: Memory at d2000000 (32-bit, non-prefetchable) [size=16K] Capabilities: [44] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME+ Kernel driver in use: ohci1394 Output of /proc/cpuinfo : processor : 0 vendor_id : GenuineIntel cpu family : 15 model : 2 model name : Intel(R) Pentium(R) 4 CPU 2.80GHz stepping : 9 cpu MHz : 2800.000 cache size : 512 KB physical id : 0 siblings : 2 core id : 0 cpu cores : 1 apicid : 0 initial apicid : 0 fdiv_bug : no hlt_bug : no f00f_bug : no coma_bug : no fpu : yes fpu_exception : yes cpuid level : 2 wp : yes flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe pebs bts cid xtpr bogomips : 5588.25 clflush size : 64 cache_alignment : 128 address sizes : 36 bits physical, 32 bits virtual power management: processor : 1 vendor_id : GenuineIntel cpu family : 15 model : 2 model name : Intel(R) Pentium(R) 4 CPU 2.80GHz stepping : 9 cpu MHz : 2800.000 cache size : 512 KB physical id : 0 siblings : 2 core id : 0 cpu cores : 1 apicid : 1 initial apicid : 1 fdiv_bug : no hlt_bug : no f00f_bug : no coma_bug : no fpu : yes fpu_exception : yes cpuid level : 2 wp : yes flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe pebs bts cid xtpr bogomips : 5588.75 clflush size : 64 cache_alignment : 128 address sizes : 36 bits physical, 32 bits virtual power management: Output of /proc/modules: nfsd 195831 11 - Live 0xe1b58000 lockd 47717 1 nfsd, Live 0xe1b08000 nfs_acl 1631 1 nfsd, Live 0xe1aec000 auth_rpcgss 25322 1 nfsd, Live 0xe1ada000 sunrpc 135022 12 nfsd,lockd,nfs_acl,auth_rpcgss, Live 0xe1a98000 exportfs 2510 1 nfsd, Live 0xe1a5a000 fuse 46204 1 - Live 0xe1a41000 snd_intel8x0 19291 0 - Live 0xe0fb9000 snd_ac97_codec 76383 1 snd_intel8x0, Live 0xe0f8f000 nouveau 463434 2 - Loading 0xe0d11000 ac97_bus 674 1 snd_ac97_codec, Live 0xe0ceb000 snd_pcm_oss 26693 0 - Live 0xe0cdb000 snd_mixer_oss 9891 1 snd_pcm_oss, Live 0xe0cc6000 snd_pcm 45958 3 snd_intel8x0,snd_ac97_codec,snd_pcm_oss, Live 0xe0c22000 ttm 35357 1 nouveau, Live 0xe0bed000 firewire_ohci 19791 0 - Live 0xe0bf8000 snd_seq 32347 0 - Live 0xe0bdd000 sg 18950 0 - Live 0xe0bc7000 cb710_mmc 4605 0 - Live 0xe0bb0000 uhci_hcd 15412 0 - Live 0xe0b8d000 snd_timer 12094 2 snd_pcm,snd_seq, Live 0xe0b70000 firewire_core 33930 1 firewire_ohci, Live 0xe0b5f000 mmc_core 40474 1 cb710_mmc, Live 0xe0b1b000 drm_kms_helper 18847 1 nouveau, Live 0xe0b0f000 sr_mod 9281 0 - Live 0xe0af5000 8139too 14094 0 - Live 0xe0aeb000 ehci_hcd 27061 0 - Live 0xe0ab2000 snd_seq_device 3589 1 snd_seq, Live 0xe0ac8000 snd 31227 8 snd_intel8x0,snd_ac97_codec,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_seq,snd_timer,snd_seq_device, Live 0xe0a43000 crc_itu_t 991 1 firewire_core, Live 0xe0a3d000 usbcore 87121 2 uhci_hcd,ehci_hcd, Live 0xe099a000 cb710 3032 1 cb710_mmc, Live 0xe0907000 ohci1394 20807 0 - Live 0xe0977000 cdrom 24719 1 sr_mod, Live 0xe096e000 8139cp 12749 0 - Live 0xe08cc000 soundcore 3415 1 snd, Live 0xe08c5000 cfbcopyarea 2598 1 nouveau, Live 0xe084c000 snd_page_alloc 4657 2 snd_intel8x0,snd_pcm, Live 0xe07bb000 cfbimgblt 1693 1 nouveau, Live 0xe07ae000 ieee1394 50780 1 ohci1394, Live 0xe07cc000 intel_agp 20179 1 - Live 0xe0910000 cfbfillrect 2406 1 nouveau, Live 0xe0904000 battery 4038 0 - Live 0xe08da000 ac 1568 0 - Live 0xe08e0000 btrfs 400920 0 - Live 0xe0851000 crc32c 2132 1 - Live 0xe07c9000 libcrc32c 602 1 btrfs, Live 0xe07bf000 sd_mod 20286 11 - Live 0xe07b1000 A+ -- Stéphane Casset LOGIDÉE sàrl Se faire plaisir d'apprendre 1a, rue Pasteur Tel : +33 388 23 69 77 casset@xxxxxxxxxxx F-67540 OSTWALD Fax : +33 388 23 69 77 http://logidee.com
one start PFN for each node early_node_map[2] active PFN ranges 0: 0x00000001 -> 0x0000009f 0: 0x00000100 -> 0x0001ff70 On node 0 totalpages: 130830 free_area_init_node: node 0, pgdat c1358380, node_mem_map c140f020 DMA zone: 32 pages used for memmap DMA zone: 0 pages reserved DMA zone: 3966 pages, LIFO batch:0 Normal zone: 991 pages used for memmap Normal zone: 125841 pages, LIFO batch:31 Using APIC driver default ACPI: PM-Timer IO Port: 0x1008 ACPI: Local APIC address 0xfee00000 ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled) ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled) ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1]) ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1]) ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0]) IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23 ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level) ACPI: IRQ9 used by override. Using ACPI (MADT) for SMP configuration information SMP: Allowing 2 CPUs, 0 hotplug CPUs nr_irqs_gsi: 40 Allocating PCI resources starting at 20000000 (gap: 20000000:dec00000) setup_percpu: NR_CPUS:2 nr_cpumask_bits:2 nr_cpu_ids:2 nr_node_ids:1 PERCPU: Embedded 13 pages/cpu @c1c00000 s29440 r0 d23808 u2097152 pcpu-alloc: s29440 r0 d23808 u2097152 alloc=1*4194304 pcpu-alloc: [0] 0 1 Built 1 zonelists in Zone order, mobility grouping on. Total pages: 129807 Kernel command line: auto BOOT_IMAGE=Linux ro root=LABEL=root PID hash table entries: 2048 (order: 1, 8192 bytes) Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) Enabling fast FPU save and restore... done. Enabling unmasked SIMD FPU exception support... done. Initializing CPU#0 Memory: 511508k/523712k available (2396k kernel code, 11812k reserved, 1042k data, 340k init, 0k highmem) virtual kernel memory layout: fixmap : 0xfff8f000 - 0xfffff000 ( 448 kB) vmalloc : 0xe0770000 - 0xfff8d000 ( 504 MB) lowmem : 0xc0000000 - 0xdff70000 ( 511 MB) .init : 0xc135c000 - 0xc13b1000 ( 340 kB) .data : 0xc125727c - 0xc135bdd4 (1042 kB) .text : 0xc1000000 - 0xc125727c (2396 kB) Checking if this processor honours the WP bit even in supervisor mode...Ok. Preemptable hierarchical RCU implementation. RCU-based detection of stalled CPUs is disabled. Verbose stalled-CPUs detection is disabled. NR_IRQS:320 Console: colour VGA+ 80x25 console [tty0] enabled Fast TSC calibration using PIT Detected 2793.243 MHz processor. Calibrating delay loop (skipped), value calculated using timer frequency.. 5588.25 BogoMIPS (lpj=9310810) pid_max: default: 32768 minimum: 301 Mount-cache hash table entries: 512 CPU: Physical Processor ID: 0 CPU: Processor Core ID: 0 Performance Events: Netburst events, Netburst P4/Xeon PMU driver. ... version: 0 ... bit width: 40 ... generic registers: 18 ... value mask: 000000ffffffffff ... max period: 0000007fffffffff ... fixed-purpose events: 0 ... event mask: 000000000003ffff ACPI: Core revision 20100702 Enabling APIC mode: Flat. Using 1 I/O APICs ..TIMER: vector=0x30 apic1=0 pin1=0 apic2=-1 pin2=-1 ..MP-BIOS bug: 8254 timer not connected to IO-APIC ...trying to set up timer (IRQ0) through the 8259A ... ..... (found apic 0 pin 0) ... ....... works. CPU0: Intel(R) Pentium(R) 4 CPU 2.80GHz stepping 09 Booting Node 0, Processors #1 Ok. Initializing CPU#1 Brought up 2 CPUs Total of 2 processors activated (11176.00 BogoMIPS). NET: Registered protocol family 16 ACPI: bus type pci registered PCI: PCI BIOS revision 2.10 entry at 0xfd972, last bus=2 PCI: Using configuration type 1 for base access bio: create slab <bio-0> at 0 ACPI: EC: Look up EC in DSDT ACPI: Interpreter enabled ACPI: (supports S0 S3 S5) ACPI: Using IOAPIC for interrupt routing ACPI: EC: GPE = 0x1d, I/O: command/status = 0x66, data = 0x62 PCI: Ignoring host bridge windows from ACPI; if necessary, use "pci=use_crs" and report a bug ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff]) pci_root PNP0A03:00: host bridge window [io 0x0000-0x0cf7] (ignored) pci_root PNP0A03:00: host bridge window [mem 0x000a0000-0x000bffff] (ignored) pci_root PNP0A03:00: host bridge window [mem 0x000d4000-0x000d7fff] (ignored) pci_root PNP0A03:00: host bridge window [mem 0x20000000-0xfebfffff] (ignored) pci_root PNP0A03:00: host bridge window [io 0x0d00-0xffff] (ignored) pci 0000:00:00.0: Enabling MCH 'Overflow' Device pci 0000:00:00.0: reg 10: [mem 0xd8000000-0xdfffffff pref] pci 0000:00:06.0: reg 10: [mem 0xfecf0000-0xfecf0fff] pci 0000:00:1d.0: reg 20: [io 0x1cc0-0x1cdf] pci 0000:00:1d.1: reg 20: [io 0x1ce0-0x1cff] pci 0000:00:1d.2: reg 20: [io 0x2000-0x201f] pci 0000:00:1d.7: reg 10: [mem 0xd0000000-0xd00003ff] pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold pci 0000:00:1d.7: PME# disabled pci 0000:00:1f.0: Force enabled HPET at 0xfed00000 pci 0000:00:1f.0: Enabled i801 SMBus device pci 0000:00:1f.0: quirk: [io 0x1000-0x107f] claimed by ICH4 ACPI/GPIO/TCO pci 0000:00:1f.0: quirk: [io 0x1180-0x11bf] claimed by ICH4 GPIO pci 0000:00:1f.1: reg 10: [io 0x0000-0x0007] pci 0000:00:1f.1: reg 14: [io 0x0000-0x0003] pci 0000:00:1f.1: reg 18: [io 0x0000-0x0007] pci 0000:00:1f.1: reg 1c: [io 0x0000-0x0003] pci 0000:00:1f.1: reg 20: [io 0x2040-0x204f] pci 0000:00:1f.1: reg 24: [mem 0x00000000-0x000003ff] pci 0000:00:1f.3: reg 20: [io 0x2020-0x203f] pci 0000:00:1f.5: reg 10: [io 0x1400-0x14ff] pci 0000:00:1f.5: reg 14: [io 0x1c80-0x1cbf] pci 0000:00:1f.5: reg 18: [mem 0xd0000c00-0xd0000dff] pci 0000:00:1f.5: reg 1c: [mem 0xd0000800-0xd00008ff] pci 0000:00:1f.5: PME# supported from D0 D3hot D3cold pci 0000:00:1f.5: PME# disabled pci 0000:00:1f.6: reg 10: [io 0x1800-0x18ff] pci 0000:00:1f.6: reg 14: [io 0x1c00-0x1c7f] pci 0000:00:1f.6: PME# supported from D0 D3hot D3cold pci 0000:00:1f.6: PME# disabled pci 0000:01:00.0: reg 10: [mem 0xd1000000-0xd1ffffff] pci 0000:01:00.0: reg 14: [mem 0xe0000000-0xefffffff pref] pci 0000:01:00.0: reg 30: [mem 0x00000000-0x0001ffff pref] pci 0000:00:01.0: PCI bridge to [bus 01-01] pci 0000:00:01.0: bridge window [io 0xf000-0x0000] (disabled) pci 0000:00:01.0: bridge window [mem 0xd1000000-0xd1ffffff] pci 0000:00:01.0: bridge window [mem 0xe0000000-0xefffffff pref] pci 0000:02:00.0: reg 10: [io 0x3000-0x30ff] pci 0000:02:00.0: reg 14: [mem 0xd2005800-0xd20058ff] pci 0000:02:00.0: supports D1 D2 pci 0000:02:00.0: PME# supported from D1 D2 D3hot D3cold pci 0000:02:00.0: PME# disabled pci 0000:02:01.0: reg 10: [mem 0xd2004000-0xd2004fff] pci 0000:02:01.0: supports D1 D2 pci 0000:02:01.0: PME# supported from D0 D1 D2 D3hot D3cold pci 0000:02:01.0: PME# disabled pci 0000:02:01.1: reg 10: [io 0x3c00-0x3c7f] pci 0000:02:01.1: supports D1 D2 pci 0000:02:01.1: PME# supported from D0 D1 D2 D3hot pci 0000:02:01.1: PME# disabled pci 0000:02:02.0: reg 10: [mem 0xd2005000-0xd20057ff] pci 0000:02:02.0: reg 14: [mem 0xd2000000-0xd2003fff] pci 0000:02:02.0: supports D1 D2 pci 0000:02:02.0: PME# supported from D0 D1 D2 D3hot pci 0000:02:02.0: PME# disabled pci 0000:00:1e.0: PCI bridge to [bus 02-02] (subtractive decode) pci 0000:00:1e.0: bridge window [io 0x3000-0x3fff] pci 0000:00:1e.0: bridge window [mem 0xd2000000-0xd23fffff] pci 0000:00:1e.0: bridge window [mem 0xfff00000-0x000fffff pref] (disabled) pci 0000:00:1e.0: bridge window [io 0x0000-0xffff] (subtractive decode) pci 0000:00:1e.0: bridge window [mem 0x00000000-0xffffffff] (subtractive decode) pci_bus 0000:03: [bus 03-06] partially hidden behind transparent bridge 0000:02 [bus 02-02] pci_bus 0000:00: on NUMA node 0 ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGP_._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.HUB_._PRT] Unable to assume PCIe control: Disabling ASPM ACPI: PCI Interrupt Link [LNKA] (IRQs 3 10 11 14 15) *5 ACPI: PCI Interrupt Link [LNKB] (IRQs 3 *10 11 14 15) ACPI: PCI Interrupt Link [LNKC] (IRQs 3 *10 11 14 15) ACPI: PCI Interrupt Link [LNKD] (IRQs 3 10 *11 14 15) ACPI: PCI Interrupt Link [LNKE] (IRQs 3 10 11 14 15) *4 ACPI: PCI Interrupt Link [LNKF] (IRQs 3 10 11 14 15) *0, disabled. ACPI: PCI Interrupt Link [LNKG] (IRQs 3 10 11 14 15) *0, disabled. ACPI: PCI Interrupt Link [LNKH] (IRQs 3 10 *11 14 15) vgaarb: device added: PCI:0000:01:00.0,decodes=io+mem,owns=io+mem,locks=none vgaarb: loaded SCSI subsystem initialized libata version 3.00 loaded. PCI: Using ACPI for IRQ routing PCI: pci_cache_line_size set to 64 bytes reserve RAM buffer: 000000000009f800 - 000000000009ffff reserve RAM buffer: 000000001ff70000 - 000000001fffffff hpet clockevent registered HPET: 3 timers in total, 0 timers will be used for per-cpu timer hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0 hpet0: 3 comparators, 64-bit 14.318180 MHz counter Switching to clocksource tsc pnp: PnP ACPI init ACPI: bus type pnp registered pnp: PnP ACPI: found 10 devices ACPI: ACPI bus type pnp unregistered system 00:01: [io 0x1000-0x10bf] could not be reserved system 00:01: [io 0x1180-0x11bf] has been reserved system 00:01: [io 0x04d0-0x04d1] has been reserved system 00:01: [io 0x0600-0x060f] has been reserved system 00:01: [io 0xfe00] has been reserved system 00:01: [io 0xfe10-0xfe11] has been reserved system 00:01: [mem 0xfecf0000-0xfecfffff] could not be reserved system 00:01: [mem 0xfed20000-0xfed8ffff] has been reserved system 00:01: [mem 0xff800000-0xffffffff] could not be reserved ACPI: EC: GPE storm detected, transactions will use polling mode pci 0000:00:1e.0: BAR 9: assigned [mem 0x20000000-0x23ffffff pref] pci 0000:00:1f.1: BAR 5: assigned [mem 0x24000000-0x240003ff] pci 0000:00:1f.1: BAR 5: set to [mem 0x24000000-0x240003ff] (PCI address [0x24000000-0x240003ff] pci 0000:01:00.0: BAR 6: can't assign mem pref (size 0x20000) pci 0000:00:01.0: PCI bridge to [bus 01-01] pci 0000:00:01.0: bridge window [io disabled] pci 0000:00:01.0: bridge window [mem 0xd1000000-0xd1ffffff] pci 0000:00:01.0: bridge window [mem 0xe0000000-0xefffffff pref] pci 0000:02:01.0: BAR 9: assigned [mem 0x20000000-0x23ffffff pref] pci 0000:02:01.0: BAR 10: assigned [mem 0x28000000-0x2bffffff] pci 0000:02:01.0: BAR 7: assigned [io 0x3400-0x34ff] pci 0000:02:01.0: BAR 8: assigned [io 0x3800-0x38ff] pci 0000:02:01.0: CardBus bridge to [bus 03-06] pci 0000:02:01.0: bridge window [io 0x3400-0x34ff] pci 0000:02:01.0: bridge window [io 0x3800-0x38ff] pci 0000:02:01.0: bridge window [mem 0x20000000-0x23ffffff pref] pci 0000:02:01.0: bridge window [mem 0x28000000-0x2bffffff] pci 0000:00:1e.0: PCI bridge to [bus 02-02] pci 0000:00:1e.0: bridge window [io 0x3000-0x3fff] pci 0000:00:1e.0: bridge window [mem 0xd2000000-0xd23fffff] pci 0000:00:1e.0: bridge window [mem 0x20000000-0x23ffffff pref] pci 0000:00:1e.0: setting latency timer to 64 pci 0000:02:01.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17 pci_bus 0000:00: resource 0 [io 0x0000-0xffff] pci_bus 0000:00: resource 1 [mem 0x00000000-0xffffffff] pci_bus 0000:01: resource 1 [mem 0xd1000000-0xd1ffffff] pci_bus 0000:01: resource 2 [mem 0xe0000000-0xefffffff pref] pci_bus 0000:02: resource 0 [io 0x3000-0x3fff] pci_bus 0000:02: resource 1 [mem 0xd2000000-0xd23fffff] pci_bus 0000:02: resource 2 [mem 0x20000000-0x23ffffff pref] pci_bus 0000:02: resource 4 [io 0x0000-0xffff] pci_bus 0000:02: resource 5 [mem 0x00000000-0xffffffff] pci_bus 0000:03: resource 0 [io 0x3400-0x34ff] pci_bus 0000:03: resource 1 [io 0x3800-0x38ff] pci_bus 0000:03: resource 2 [mem 0x20000000-0x23ffffff pref] pci_bus 0000:03: resource 3 [mem 0x28000000-0x2bffffff] NET: Registered protocol family 2 IP route cache hash table entries: 4096 (order: 2, 16384 bytes) TCP established hash table entries: 16384 (order: 5, 131072 bytes) TCP bind hash table entries: 16384 (order: 5, 131072 bytes) TCP: Hash tables configured (established 16384 bind 16384) TCP reno registered UDP hash table entries: 256 (order: 1, 8192 bytes) UDP-Lite hash table entries: 256 (order: 1, 8192 bytes) NET: Registered protocol family 1 pci 0000:01:00.0: Boot video device PCI: CLS mismatch (1020 != 32), using 64 bytes Trying to unpack rootfs image as initramfs... Freeing initrd memory: 3012k freed Simple Boot Flag at 0x36 set to 0x1 msgmni has been set to 1004 io scheduler noop registered io scheduler deadline registered (default) io scheduler cfq registered input: Sleep Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A03:00/PNP0C0E:00/input/input0 ACPI: Sleep Button [SBTN] input: Lid Switch as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0D:00/input/input1 ACPI: Lid Switch [LID] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input2 ACPI: Power Button [PWRF] ACPI: acpi_idle registered with cpuidle Marking TSC unstable due to TSC halts in idle Switching to clocksource hpet ACPI: Invalid PBLK length [0] thermal LNXTHERM:01: registered as thermal_zone0 ACPI: Thermal Zone [THRM] (51 C) Real Time Clock Driver v1.12b Linux agpgart interface v0.103 [drm] Initialized drm 1.1.0 20060810 brd: module loaded ata_piix 0000:00:1f.1: version 2.13 ata_piix 0000:00:1f.1: enabling device (0005 -> 0007) ata_piix 0000:00:1f.1: PCI INT A -> GSI 18 (level, low) -> IRQ 18 ata_piix 0000:00:1f.1: setting latency timer to 64 scsi0 : ata_piix scsi1 : ata_piix ata1: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0x2040 irq 14 ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0x2048 irq 15 PNP: PS/2 Controller [PNP0303:KBC0,PNP0f13:MSE0] at 0x60,0x64 irq 1,12 serio: i8042 KBD port at 0x60,0x64 irq 1 serio: i8042 AUX port at 0x60,0x64 irq 12 mice: PS/2 mouse device common for all mice md: linear personality registered for level -1 md: raid0 personality registered for level 0 md: raid1 personality registered for level 1 md: raid10 personality registered for level 10 md: multipath personality registered for level -4 md: faulty personality registered for level -5 device-mapper: ioctl: 4.18.0-ioctl (2010-06-29) initialised: dm-devel@xxxxxxxxxx cpuidle: using governor ladder cpuidle: using governor menu IPv4 over IPv4 tunneling driver GRE over IPv4 tunneling driver TCP cubic registered Initializing XFRM netlink socket NET: Registered protocol family 17 NET: Registered protocol family 15 Registering the dns_resolver key type p4-clockmod: P4/Xeon(TM) CPU On-Demand Clock Modulation available Using IPI No-Shortcut mode input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input3 ata2.00: ATAPI: HL-DT-STCD-RW/DVD DRIVE GCC-4241N, 0C27, max MWDMA2 ata1.00: ATA-6: HTS541010G9AT00, MBZOA60A, max UDMA/100 ata1.00: 195371568 sectors, multi 16: LBA48 ata2.00: configured for MWDMA2 ata1.00: configured for UDMA/100 scsi 0:0:0:0: Direct-Access ATA HTS541010G9AT00 MBZO PQ: 0 ANSI: 5 scsi 1:0:0:0: CD-ROM HL-DT-ST RW/DVD GCC-4241N 0C27 PQ: 0 ANSI: 5 Freeing unused kernel memory: 340k freed Write protecting the kernel text: 2400k Write protecting the kernel read-only data: 856k udevd (984): /proc/984/oom_adj is deprecated, please use /proc/984/oom_score_adj instead. sd 0:0:0:0: [sda] 195371568 512-byte logical blocks: (100 GB/93.1 GiB) sd 0:0:0:0: [sda] Write Protect is off sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA Synaptics Touchpad, model: 1, fw: 5.9, id: 0x236eb1, caps: 0xa04711/0xa/0x0 input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio1/input/input4 sda: sda1 sda2 sda3 sda4 < sda5 sda6 sda7 sda8 sda9 sda10 sda11 sda12 sda13 sda14 > sd 0:0:0:0: [sda] Attached SCSI disk Btrfs loaded EXT4-fs (sda5): mounted filesystem with ordered data mode. Opts: (null) udev: starting version 161 ACPI: AC Adapter [ACAD] (on-line) ACPI: Battery Slot [BAT1] (battery present) agpgart-intel 0000:00:00.0: Intel 865 Chipset agpgart-intel 0000:00:00.0: AGP aperture is 128M @ 0xd8000000 8139cp: 8139cp: 10/100 PCI Ethernet driver v1.3 (Mar 22, 2004) 8139cp 0000:02:00.0: This (id 10ec:8139 rev 10) is not an 8139C+ compatible chip, use 8139too ohci1394 0000:02:02.0: PCI INT A -> GSI 19 (level, low) -> IRQ 19 ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[19] MMIO=[d2005000-d20057ff] Max Packet=[2048] IR/IT contexts=[4/8] cb710 0000:02:01.1: PCI INT B -> GSI 18 (level, low) -> IRQ 18 cb710 0000:02:01.1: id 0, IO 0x00013c00, IRQ 18 usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver ehci_hcd 0000:00:1d.7: PCI INT D -> GSI 23 (level, low) -> IRQ 23 ehci_hcd 0000:00:1d.7: setting latency timer to 64 ehci_hcd 0000:00:1d.7: EHCI Host Controller ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1 ehci_hcd 0000:00:1d.7: debug port 1 ehci_hcd 0000:00:1d.7: cache line size of 64 is not supported ehci_hcd 0000:00:1d.7: irq 23, io mem 0xd0000000 8139too: 8139too Fast Ethernet driver 0.9.28 8139too 0000:02:00.0: PCI INT A -> GSI 20 (level, low) -> IRQ 20 8139too 0000:02:00.0: eth0: RealTek RTL8139 at 0x3000, 00:c0:9f:29:f7:ea, IRQ 20 ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00 hub 1-0:1.0: USB hub found hub 1-0:1.0: 6 ports detected sr0: scsi3-mmc drive: 24x/24x writer cd/rw xa/form2 cdda tray cdrom: Uniform CD-ROM driver Revision: 3.20 sr 1:0:0:0: Attached scsi CD-ROM sr0 uhci_hcd: USB Universal Host Controller Interface driver uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 uhci_hcd 0000:00:1d.0: setting latency timer to 64 uhci_hcd 0000:00:1d.0: UHCI Host Controller uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2 uhci_hcd 0000:00:1d.0: irq 16, io base 0x00001cc0 hub 2-0:1.0: USB hub found hub 2-0:1.0: 2 ports detected uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19 uhci_hcd 0000:00:1d.1: setting latency timer to 64 uhci_hcd 0000:00:1d.1: UHCI Host Controller uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3 uhci_hcd 0000:00:1d.1: irq 19, io base 0x00001ce0 hub 3-0:1.0: USB hub found hub 3-0:1.0: 2 ports detected uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18 uhci_hcd 0000:00:1d.2: setting latency timer to 64 uhci_hcd 0000:00:1d.2: UHCI Host Controller uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4 uhci_hcd 0000:00:1d.2: irq 18, io base 0x00002000 hub 4-0:1.0: USB hub found hub 4-0:1.0: 2 ports detected sd 0:0:0:0: Attached scsi generic sg0 type 0 sr 1:0:0:0: Attached scsi generic sg1 type 5 nouveau 0000:01:00.0: power state changed by ACPI to D0 nouveau 0000:01:00.0: power state changed by ACPI to D0 nouveau 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [drm] nouveau 0000:01:00.0: Detected an NV30 generation card (0x031a00a1) [drm] nouveau 0000:01:00.0: Attempting to load BIOS image from PRAMIN [drm] nouveau 0000:01:00.0: ... BIOS checksum invalid [drm] nouveau 0000:01:00.0: Attempting to load BIOS image from PROM [drm] nouveau 0000:01:00.0: ... BIOS signature not found [drm] nouveau 0000:01:00.0: Attempting to load BIOS image from PCIROM [drm] nouveau 0000:01:00.0: ... appears to be valid [drm] nouveau 0000:01:00.0: BMP BIOS found [drm] nouveau 0000:01:00.0: BMP version 5.39 [drm] nouveau 0000:01:00.0: Bios version 04.31.20.46 [drm] nouveau 0000:01:00.0: Found Display Configuration Block version 2.2 [drm] nouveau 0000:01:00.0: Raw DCB entry 0: 03000223 00000005 [drm] nouveau 0000:01:00.0: Raw DCB entry 1: 01010100 000088b8 [drm] nouveau 0000:01:00.0: Raw DCB entry 2: 020303f1 00000003 [drm] nouveau 0000:01:00.0: Loading NV17 power sequencing microcode [drm] nouveau 0000:01:00.0: Parsing VBIOS init table 0 at offset 0xEC86 [drm] nouveau 0000:01:00.0: Parsing VBIOS init table 1 at offset 0xEFE5 [drm] nouveau 0000:01:00.0: Parsing VBIOS init table 2 at offset 0xF148 [drm] nouveau 0000:01:00.0: Parsing VBIOS init table 3 at offset 0xF2AF [drm] nouveau 0000:01:00.0: Parsing VBIOS init table 4 at offset 0xF2CC [drm] nouveau 0000:01:00.0: Parsing VBIOS init table 5 at offset 0xF2E9 Intel ICH 0000:00:1f.5: PCI INT B -> GSI 17 (level, low) -> IRQ 17 Intel ICH 0000:00:1f.5: setting latency timer to 64 BUG: unable to handle kernel paging request at fffa6ff0 IP: [<c1105185>] iowrite32+0xa/0x29 *pde = 013b9067 *pte = 00000000 Oops: 0002 [#1] PREEMPT SMP last sysfs file: /sys/module/usbcore/initstate Modules linked in: snd_intel8x0(+) snd_ac97_codec nouveau(+) ac97_bus snd_pcm_oss snd_mixer_oss snd_pcm ttm firewire_ohci snd_seq sg cb710_mmc uhci_hcd snd_timer firewire_core mmc_core drm_kms_helper sr_mod 8139too ehci_hcd snd_seq_device snd crc_itu_t usbcore cb710 ohci1394 cdrom 8139cp soundcore cfbcopyarea snd_page_alloc cfbimgblt ieee1394 intel_agp cfbfillrect battery ac btrfs crc32c libcrc32c sd_mod Pid: 1385, comm: modprobe Not tainted 2.6.36-rc2-git1 #81 0880/Pavilion zd7000 (DP761E#ABF) EIP: 0060:[<c1105185>] EFLAGS: 00010292 CPU: 1 EIP is at iowrite32+0xa/0x29 EAX: 04000000 EBX: 00000ffc ECX: fffa6ff0 EDX: fffa6ff0 ESI: 04000000 EDI: fffa3000 EBP: df2008c0 ESP: dfa95cdc DS: 007b ES: 007b FS: 00d8 GS: 0033 SS: 0068 Process modprobe (pid: 1385, ti=dfa94000 task=dee9ca90 task.ti=dfa94000) Stack: e0d28d38 def2dd60 04000000 10000000 e0d28ed3 04000000 def83800 00000300 <0> e0d2521c 00000001 df2008e8 dfa95d64 0000016b df2008c0 0000f4c7 0000015c <0> 00000023 e0d23f3d e0d6883d c1253e4b 0000015c dfa95d64 00000002 df2008c0 Call Trace: [<e0d28d38>] ? poke_fb+0x63/0x7b [nouveau] [<e0d28ed3>] ? init_compute_mem+0x110/0x9f3 [nouveau] [<e0d2521c>] ? bios_wr32+0x64/0xc7 [nouveau] [<e0d23f3d>] ? parse_init_table+0xc9/0x192 [nouveau] [<c1253e4b>] ? printk+0xe/0x13 [<e0d2abf5>] ? nouveau_run_vbios_init+0x261/0x310 [nouveau] [<e0d2c078>] ? nouveau_bios_init+0x13d4/0x1708 [nouveau] [<e0d12611>] ? nouveau_card_init+0xbbe/0xee2 [nouveau] [<e0d12da3>] ? nouveau_load+0x46e/0x4a6 [nouveau] [<c116d997>] ? drm_get_pci_dev+0x117/0x1e9 [<c1255e09>] ? _raw_spin_lock_irqsave+0x11/0x2a [<c110fa01>] ? local_pci_probe+0x34/0x74 [<c11100c4>] ? pci_device_probe+0x41/0x63 [<c1178451>] ? driver_probe_device+0x8c/0x110 [<c1178515>] ? __driver_attach+0x40/0x5b [<c1177e66>] ? bus_for_each_dev+0x37/0x5f [<c1178307>] ? driver_attach+0x11/0x13 [<c11784d5>] ? __driver_attach+0x0/0x5b [<c1177941>] ? bus_add_driver+0x8c/0x1bf [<c10fcc63>] ? kset_find_obj+0x4f/0x56 [<e0d79000>] ? nouveau_init+0x0/0x40 [nouveau] [<c1178730>] ? driver_register+0x7a/0xd9 [<e0d79000>] ? nouveau_init+0x0/0x40 [nouveau] [<c1110296>] ? __pci_register_driver+0x33/0x89 [<e0d79000>] ? nouveau_init+0x0/0x40 [nouveau] [<c1001151>] ? do_one_initcall+0x68/0x106 [<c1048c77>] ? sys_init_module+0xbe2/0xdc7 [<c10742ac>] ? sys_close+0x6b/0x9e [<c1002690>] ? sysenter_do_call+0x12/0x26 Code: 00 01 00 76 0d 25 ff ff 00 00 89 d7 89 c2 f3 6c eb 0c ba 01 67 2d c1 5b 5f e9 6d fe ff ff 5b 5f c3 89 d1 81 fa ff ff 03 00 76 03 <89> 02 c3 81 fa 00 00 01 00 76 08 81 e2 ff ff 00 00 ef c3 ba 16 EIP: [<c1105185>] iowrite32+0xa/0x29 SS:ESP 0068:dfa95cdc CR2: 00000000fffa6ff0 ---[ end trace 893c12fda0bab2d9 ]--- note: modprobe[1385] exited with preempt_count 1 BUG: scheduling while atomic: modprobe/1385/0x10000002 Modules linked in: snd_intel8x0(+) snd_ac97_codec nouveau(+) ac97_bus snd_pcm_oss snd_mixer_oss snd_pcm ttm firewire_ohci snd_seq sg cb710_mmc uhci_hcd snd_timer firewire_core mmc_core drm_kms_helper sr_mod 8139too ehci_hcd snd_seq_device snd crc_itu_t usbcore cb710 ohci1394 cdrom 8139cp soundcore cfbcopyarea snd_page_alloc cfbimgblt ieee1394 intel_agp cfbfillrect battery ac btrfs crc32c libcrc32c sd_mod Pid: 1385, comm: modprobe Tainted: G D 2.6.36-rc2-git1 #81 Call Trace: [<c1254160>] ? schedule+0x9b/0x6b1 [<c1022222>] ? __cond_resched+0xf/0x19 [<c1254803>] ? _cond_resched+0x18/0x21 [<c106535e>] ? unmap_vmas+0x444/0x514 [<c10682d1>] ? exit_mmap+0x99/0x130 [<c1022b23>] ? mmput+0x20/0x94 ieee1394: Host added: ID:BUS[0-00:1023] GUID[00508b0880000a22] [<c1025d00>] ? exit_mm+0xdf/0xe7 [<c102718c>] ? do_exit+0x180/0x562 [<c1255e99>] ? _raw_spin_trylock+0xd/0x4e [<c1025144>] ? kmsg_dump+0x7f/0xf5 [<c1004e80>] ? oops_end+0x72/0x75 [<c1017bd1>] ? no_context+0x10d/0x116 [<c1017df1>] ? do_page_fault+0x0/0x2fc [<c1017cd8>] ? bad_area_nosemaphore+0xa/0xc [<c1017f3d>] ? do_page_fault+0x14c/0x2fc [<c101eea1>] ? get_parent_ip+0x8/0x19 [<c101fabb>] ? sub_preempt_count+0x74/0x80 [<c1255c11>] ? _raw_spin_unlock+0xc/0x1f [<c1019bd3>] ? reserve_memtype+0x2e2/0x372 [<c101fabb>] ? sub_preempt_count+0x74/0x80 [<c125474e>] ? schedule+0x689/0x6b1 [<c101eea1>] ? get_parent_ip+0x8/0x19 [<c1017df1>] ? do_page_fault+0x0/0x2fc [<c12566a2>] ? error_code+0x5a/0x60 [<c101007b>] ? speedstep_get_freqs+0xd0/0x11e [<c1017df1>] ? do_page_fault+0x0/0x2fc [<c1105185>] ? iowrite32+0xa/0x29 [<e0d28d38>] ? poke_fb+0x63/0x7b [nouveau] [<e0d28ed3>] ? init_compute_mem+0x110/0x9f3 [nouveau] [<e0d2521c>] ? bios_wr32+0x64/0xc7 [nouveau] [<e0d23f3d>] ? parse_init_table+0xc9/0x192 [nouveau] [<c1253e4b>] ? printk+0xe/0x13 [<e0d2abf5>] ? nouveau_run_vbios_init+0x261/0x310 [nouveau] [<e0d2c078>] ? nouveau_bios_init+0x13d4/0x1708 [nouveau] [<e0d12611>] ? nouveau_card_init+0xbbe/0xee2 [nouveau] [<e0d12da3>] ? nouveau_load+0x46e/0x4a6 [nouveau] [<c116d997>] ? drm_get_pci_dev+0x117/0x1e9 [<c1255e09>] ? _raw_spin_lock_irqsave+0x11/0x2a [<c110fa01>] ? local_pci_probe+0x34/0x74 [<c11100c4>] ? pci_device_probe+0x41/0x63 [<c1178451>] ? driver_probe_device+0x8c/0x110 [<c1178515>] ? __driver_attach+0x40/0x5b [<c1177e66>] ? bus_for_each_dev+0x37/0x5f [<c1178307>] ? driver_attach+0x11/0x13 [<c11784d5>] ? __driver_attach+0x0/0x5b [<c1177941>] ? bus_add_driver+0x8c/0x1bf [<c10fcc63>] ? kset_find_obj+0x4f/0x56 [<e0d79000>] ? nouveau_init+0x0/0x40 [nouveau] [<c1178730>] ? driver_register+0x7a/0xd9 [<e0d79000>] ? nouveau_init+0x0/0x40 [nouveau] [<c1110296>] ? __pci_register_driver+0x33/0x89 [<e0d79000>] ? nouveau_init+0x0/0x40 [nouveau] [<c1001151>] ? do_one_initcall+0x68/0x106 [<c1048c77>] ? sys_init_module+0xbe2/0xdc7 [<c10742ac>] ? sys_close+0x6b/0x9e [<c1002690>] ? sysenter_do_call+0x12/0x26 intel8x0_measure_ac97_clock: measured 53235 usecs (2565 samples) intel8x0: clocking to 48000 Adding 497976k swap on /dev/sda6. Priority:-1 extents:1 across:497976k EXT4-fs (sda5): re-mounted. Opts: (null) EXT4-fs (sda5): re-mounted. Opts: errors=remount-ro EXT4-fs (sda9): mounted filesystem with writeback data mode. Opts: data=writeback EXT4-fs (sda7): mounted filesystem with ordered data mode. Opts: (null) EXT4-fs (sda8): mounted filesystem with writeback data mode. Opts: data=writeback EXT4-fs (dm-1): mounted filesystem with writeback data mode. Opts: data=writeback EXT4-fs (dm-0): mounted filesystem with writeback data mode. Opts: data=writeback eth0: link up, 100Mbps, full-duplex, lpa 0x45E1 fuse init (API version 7.15) RPC: Registered udp transport module. RPC: Registered tcp transport module. RPC: Registered tcp NFSv4.1 backchannel transport module. Installing knfsd (copyright (C) 1996 okir@xxxxxxxxxxxx). NFSD: Using /var/lib/nfs/v4recovery as the NFSv4 state recovery directory NFSD: starting 90-second grace period BUG: unable to handle kernel NULL pointer dereference at (null) IP: [<c1254d67>] __mutex_lock_slowpath+0xa0/0x132 *pde = 00000000 Oops: 0002 [#2] PREEMPT SMP last sysfs file: /sys/devices/pci0000:00/0000:00:01.0/0000:01:00.0/boot_vga Modules linked in: nfsd lockd nfs_acl auth_rpcgss sunrpc exportfs fuse snd_intel8x0 snd_ac97_codec nouveau(+) ac97_bus snd_pcm_oss snd_mixer_oss snd_pcm ttm firewire_ohci snd_seq sg cb710_mmc uhci_hcd snd_timer firewire_core mmc_core drm_kms_helper sr_mod 8139too ehci_hcd snd_seq_device snd crc_itu_t usbcore cb710 ohci1394 cdrom 8139cp soundcore cfbcopyarea snd_page_alloc cfbimgblt ieee1394 intel_agp cfbfillrect battery ac btrfs crc32c libcrc32c sd_mod Pid: 2610, comm: Xorg Tainted: G D 2.6.36-rc2-git1 #81 0880/Pavilion zd7000 (DP761E#ABF) EIP: 0060:[<c1254d67>] EFLAGS: 00013246 CPU: 0 EIP is at __mutex_lock_slowpath+0xa0/0x132 EAX: 00000000 EBX: def83a98 ECX: dedd2040 EDX: dcd5ff14 ESI: dedd2040 EDI: def83a9c EBP: def83aa0 ESP: dcd5ff10 DS: 007b ES: 007b FS: 00d8 GS: 0033 SS: 0068 Process Xorg (pid: 2610, ti=dcd5e000 task=dedd2040 task.ti=dcd5e000) Stack: c1169934 def83aa0 00000000 dedd2040 def83a98 de9a1100 def83a98 de9a1160 <0> c1254c5a de9a1124 de9a1100 c116f60c def83800 de9a1100 de9a115c c1168f8f <0> 00000000 def83a00 def839f8 00003246 deecea80 00000008 deb72238 df879c80 Call Trace: [<c1169934>] ? drm_gem_object_release_handle+0x0/0x24 [<c1254c5a>] ? mutex_lock+0x10/0x1d [<c116f60c>] ? drm_fb_release+0x1b/0x63 [<c1168f8f>] ? drm_release+0x2b7/0x4ae [<c10768ee>] ? fput+0xc6/0x167 [<c107423b>] ? filp_close+0x4e/0x54 [<c10742ac>] ? sys_close+0x6b/0x9e [<c1002690>] ? sysenter_do_call+0x12/0x26 [<c1250000>] ? init_cyrix+0x97/0x3b4 Code: 75 0a 83 7e 18 63 7e 04 f3 90 eb 9e 8d 7b 04 89 f8 e8 d0 10 00 00 8d 6b 08 8b 43 0c 8d 54 24 04 89 53 0c 89 6c 24 04 89 44 24 08 <89> 10 89 74 24 0c 83 c8 ff 87 03 48 74 37 83 c8 ff 87 03 48 74 EIP: [<c1254d67>] __mutex_lock_slowpath+0xa0/0x132 SS:ESP 0068:dcd5ff10 CR2: 0000000000000000 ---[ end trace 893c12fda0bab2da ]--- note: Xorg[2610] exited with preempt_count 2 BUG: scheduling while atomic: Xorg/2610/0x10000003 Modules linked in: nfsd lockd nfs_acl auth_rpcgss sunrpc exportfs fuse snd_intel8x0 snd_ac97_codec nouveau(+) ac97_bus snd_pcm_oss snd_mixer_oss snd_pcm ttm firewire_ohci snd_seq sg cb710_mmc uhci_hcd snd_timer firewire_core mmc_core drm_kms_helper sr_mod 8139too ehci_hcd snd_seq_device snd crc_itu_t usbcore cb710 ohci1394 cdrom 8139cp soundcore cfbcopyarea snd_page_alloc cfbimgblt ieee1394 intel_agp cfbfillrect battery ac btrfs crc32c libcrc32c sd_mod Pid: 2610, comm: Xorg Tainted: G D 2.6.36-rc2-git1 #81 Call Trace: [<c1254160>] ? schedule+0x9b/0x6b1 [<c1022222>] ? __cond_resched+0xf/0x19 [<c1254803>] ? _cond_resched+0x18/0x21 [<c106535e>] ? unmap_vmas+0x444/0x514 [<c10682d1>] ? exit_mmap+0x99/0x130 [<c1022b23>] ? mmput+0x20/0x94 [<c1025d00>] ? exit_mm+0xdf/0xe7 [<c102718c>] ? do_exit+0x180/0x562 [<c1255e99>] ? _raw_spin_trylock+0xd/0x4e [<c1025144>] ? kmsg_dump+0x7f/0xf5 [<c1004e80>] ? oops_end+0x72/0x75 [<c1017bd1>] ? no_context+0x10d/0x116 [<c1017df1>] ? do_page_fault+0x0/0x2fc [<c1017cd8>] ? bad_area_nosemaphore+0xa/0xc [<c1017f3d>] ? do_page_fault+0x14c/0x2fc [<c102890b>] ? __do_softirq+0xbc/0xf1 [<c1003b44>] ? do_IRQ+0x81/0x92 [<c1017df1>] ? do_page_fault+0x0/0x2fc [<c12566a2>] ? error_code+0x5a/0x60 [<c1017df1>] ? do_page_fault+0x0/0x2fc [<c1254d67>] ? __mutex_lock_slowpath+0xa0/0x132 [<c1169934>] ? drm_gem_object_release_handle+0x0/0x24 [<c1254c5a>] ? mutex_lock+0x10/0x1d [<c116f60c>] ? drm_fb_release+0x1b/0x63 [<c1168f8f>] ? drm_release+0x2b7/0x4ae [<c10768ee>] ? fput+0xc6/0x167 [<c107423b>] ? filp_close+0x4e/0x54 [<c10742ac>] ? sys_close+0x6b/0x9e [<c1002690>] ? sysenter_do_call+0x12/0x26 [<c1250000>] ? init_cyrix+0x97/0x3b4
ksymoops 2.4.11 on i686 2.6.36-rc2-git1. Options used -V (default) -k /proc/ksyms (default) -l /proc/modules (default) -o /lib/modules/2.6.36-rc2-git1/ (default) -m /boot/System.map-2.6.36-rc2-git1 (default) Warning: You did not tell me where to find symbol information. I will assume that the log matches the kernel and modules that are running right now and I'll use the default options above for symbol resolution. If the current kernel and/or modules do not match the log, you can get more accurate output by telling me the kernel version and where to find map, modules, ksyms etc. ksymoops -h explains the options. Error (regular_file): read_ksyms stat /proc/ksyms failed No modules in ksyms, skipping objects No ksyms, skipping lsmod ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1]) ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1]) 8139cp: 8139cp: 10/100 PCI Ethernet driver v1.3 (Mar 22, 2004) 8139cp 0000:02:00.0: This (id 10ec:8139 rev 10) is not an 8139C+ compatible chip, use 8139too cb710 0000:02:01.1: PCI INT B -> GSI 18 (level, low) -> IRQ 18 cb710 0000:02:01.1: id 0, IO 0x00013c00, IRQ 18 ehci_hcd 0000:00:1d.7: debug port 1 8139too: 8139too Fast Ethernet driver 0.9.28 8139too 0000:02:00.0: PCI INT A -> GSI 20 (level, low) -> IRQ 20 8139too 0000:02:00.0: eth0: RealTek RTL8139 at 0x3000, 00:c0:9f:29:f7:ea, IRQ 20 BUG: unable to handle kernel paging request at fffa6ff0 *pde = 013b9067 *pte = 00000000 Oops: 0002 [#1] PREEMPT SMP Pid: 1385, comm: modprobe Not tainted 2.6.36-rc2-git1 #81 0880/Pavilion zd7000 (DP761E#ABF) EIP: 0060:[<c1105185>] EFLAGS: 00010292 CPU: 1 Using defaults from ksymoops -t elf32-i386 -a i386 EAX: 04000000 EBX: 00000ffc ECX: fffa6ff0 EDX: fffa6ff0 ESI: 04000000 EDI: fffa3000 EBP: df2008c0 ESP: dfa95cdc DS: 007b ES: 007b FS: 00d8 GS: 0033 SS: 0068 e0d28d38 def2dd60 04000000 10000000 e0d28ed3 04000000 def83800 00000300 <0> e0d2521c 00000001 df2008e8 dfa95d64 0000016b df2008c0 0000f4c7 0000015c <0> 00000023 e0d23f3d e0d6883d c1253e4b 0000015c dfa95d64 00000002 df2008c0 Call Trace: [<e0d28d38>] ? poke_fb+0x63/0x7b [nouveau] [<e0d28ed3>] ? init_compute_mem+0x110/0x9f3 [nouveau] [<e0d2521c>] ? bios_wr32+0x64/0xc7 [nouveau] [<e0d23f3d>] ? parse_init_table+0xc9/0x192 [nouveau] [<c1253e4b>] ? printk+0xe/0x13 [<e0d2abf5>] ? nouveau_run_vbios_init+0x261/0x310 [nouveau] [<e0d2c078>] ? nouveau_bios_init+0x13d4/0x1708 [nouveau] [<e0d12611>] ? nouveau_card_init+0xbbe/0xee2 [nouveau] [<e0d12da3>] ? nouveau_load+0x46e/0x4a6 [nouveau] [<c116d997>] ? drm_get_pci_dev+0x117/0x1e9 [<c1255e09>] ? _raw_spin_lock_irqsave+0x11/0x2a [<c110fa01>] ? local_pci_probe+0x34/0x74 [<c11100c4>] ? pci_device_probe+0x41/0x63 [<c1178451>] ? driver_probe_device+0x8c/0x110 [<c1178515>] ? __driver_attach+0x40/0x5b [<c1177e66>] ? bus_for_each_dev+0x37/0x5f [<c1178307>] ? driver_attach+0x11/0x13 [<c11784d5>] ? __driver_attach+0x0/0x5b [<c1177941>] ? bus_add_driver+0x8c/0x1bf [<c10fcc63>] ? kset_find_obj+0x4f/0x56 [<e0d79000>] ? nouveau_init+0x0/0x40 [nouveau] [<c1178730>] ? driver_register+0x7a/0xd9 [<e0d79000>] ? nouveau_init+0x0/0x40 [nouveau] [<c1110296>] ? __pci_register_driver+0x33/0x89 [<e0d79000>] ? nouveau_init+0x0/0x40 [nouveau] [<c1001151>] ? do_one_initcall+0x68/0x106 [<c1048c77>] ? sys_init_module+0xbe2/0xdc7 [<c10742ac>] ? sys_close+0x6b/0x9e [<c1002690>] ? sysenter_do_call+0x12/0x26 Code: 00 01 00 76 0d 25 ff ff 00 00 89 d7 89 c2 f3 6c eb 0c ba 01 67 2d c1 5b 5f e9 6d fe ff ff 5b 5f c3 89 d1 81 fa ff ff 03 00 76 03 <89> 02 c3 81 fa 00 00 01 00 76 08 81 e2 ff ff 00 00 ef c3 ba 16 >>EIP; c1105185 <iowrite32+a/29> <===== >>EAX; 04000000 <phys_startup_32+3000000/c0000000> >>ESI; 04000000 <phys_startup_32+3000000/c0000000> Trace; e0d28d38 <END_OF_CODE+1f880d38/????> Trace; e0d28ed3 <END_OF_CODE+1f880ed3/????> Trace; e0d2521c <END_OF_CODE+1f87d21c/????> Trace; e0d23f3d <END_OF_CODE+1f87bf3d/????> Trace; c1253e4b <printk+e/13> Trace; e0d2abf5 <END_OF_CODE+1f882bf5/????> Trace; e0d2c078 <END_OF_CODE+1f884078/????> Trace; e0d12611 <END_OF_CODE+1f86a611/????> Trace; e0d12da3 <END_OF_CODE+1f86ada3/????> Trace; c116d997 <drm_get_pci_dev+117/1e9> Trace; c1255e09 <_raw_spin_lock_irqsave+11/2a> Trace; c110fa01 <local_pci_probe+34/74> Trace; c11100c4 <pci_device_probe+41/63> Trace; c1178451 <driver_probe_device+8c/110> Trace; c1178515 <__driver_attach+40/5b> Trace; c1177e66 <bus_for_each_dev+37/5f> Trace; c1178307 <driver_attach+11/13> Trace; c11784d5 <__driver_attach+0/5b> Trace; c1177941 <bus_add_driver+8c/1bf> Trace; c10fcc63 <kset_find_obj+4f/56> Trace; e0d79000 <END_OF_CODE+1f8d1000/????> Trace; c1178730 <driver_register+7a/d9> Trace; e0d79000 <END_OF_CODE+1f8d1000/????> Trace; c1110296 <__pci_register_driver+33/89> Trace; e0d79000 <END_OF_CODE+1f8d1000/????> Trace; c1001151 <do_one_initcall+68/106> Trace; c1048c77 <sys_init_module+be2/dc7> Trace; c10742ac <sys_close+6b/9e> Trace; c1002690 <sysenter_do_call+12/26> Code; c110515a <ioread8_rep+17/38> 00000000 <_EIP>: Code; c110515a <ioread8_rep+17/38> 0: 00 01 add %al,(%ecx) Code; c110515c <ioread8_rep+19/38> 2: 00 76 0d add %dh,0xd(%esi) Code; c110515f <ioread8_rep+1c/38> 5: 25 ff ff 00 00 and $0xffff,%eax Code; c1105164 <ioread8_rep+21/38> a: 89 d7 mov %edx,%edi Code; c1105166 <ioread8_rep+23/38> c: 89 c2 mov %eax,%edx Code; c1105168 <ioread8_rep+25/38> e: f3 6c rep insb (%dx),%es:(%edi) Code; c110516a <ioread8_rep+27/38> 10: eb 0c jmp 1e <_EIP+0x1e> Code; c110516c <ioread8_rep+29/38> 12: ba 01 67 2d c1 mov $0xc12d6701,%edx Code; c1105171 <ioread8_rep+2e/38> 17: 5b pop %ebx Code; c1105172 <ioread8_rep+2f/38> 18: 5f pop %edi Code; c1105173 <ioread8_rep+30/38> 19: e9 6d fe ff ff jmp fffffe8b <_EIP+0xfffffe8b> Code; c1105178 <ioread8_rep+35/38> 1e: 5b pop %ebx Code; c1105179 <ioread8_rep+36/38> 1f: 5f pop %edi Code; c110517a <ioread8_rep+37/38> 20: c3 ret Code; c110517b <iowrite32+0/29> 21: 89 d1 mov %edx,%ecx Code; c110517d <iowrite32+2/29> 23: 81 fa ff ff 03 00 cmp $0x3ffff,%edx Code; c1105183 <iowrite32+8/29> 29: 76 03 jbe 2e <_EIP+0x2e> Code; c1105185 <iowrite32+a/29> <===== 2b: 89 02 mov %eax,(%edx) <===== Code; c1105187 <iowrite32+c/29> 2d: c3 ret Code; c1105188 <iowrite32+d/29> 2e: 81 fa 00 00 01 00 cmp $0x10000,%edx Code; c110518e <iowrite32+13/29> 34: 76 08 jbe 3e <_EIP+0x3e> Code; c1105190 <iowrite32+15/29> 36: 81 e2 ff ff 00 00 and $0xffff,%edx Code; c1105196 <iowrite32+1b/29> 3c: ef out %eax,(%dx) Code; c1105197 <iowrite32+1c/29> 3d: c3 ret Code; c1105198 <iowrite32+1d/29> 3e: ba .byte 0xba Code; c1105199 <iowrite32+1e/29> 3f: 16 push %ss EIP: [<c1105185>] iowrite32+0xa/0x29 SS:ESP 0068:dfa95cdc CR2: 00000000fffa6ff0 Pid: 1385, comm: modprobe Tainted: G D 2.6.36-rc2-git1 #81 Call Trace: [<c1254160>] ? schedule+0x9b/0x6b1 [<c1022222>] ? __cond_resched+0xf/0x19 [<c1254803>] ? _cond_resched+0x18/0x21 [<c106535e>] ? unmap_vmas+0x444/0x514 [<c10682d1>] ? exit_mmap+0x99/0x130 [<c1022b23>] ? mmput+0x20/0x94 [<c1025d00>] ? exit_mm+0xdf/0xe7 [<c102718c>] ? do_exit+0x180/0x562 [<c1255e99>] ? _raw_spin_trylock+0xd/0x4e [<c1025144>] ? kmsg_dump+0x7f/0xf5 [<c1004e80>] ? oops_end+0x72/0x75 [<c1017bd1>] ? no_context+0x10d/0x116 [<c1017df1>] ? do_page_fault+0x0/0x2fc [<c1017cd8>] ? bad_area_nosemaphore+0xa/0xc [<c1017f3d>] ? do_page_fault+0x14c/0x2fc [<c101eea1>] ? get_parent_ip+0x8/0x19 [<c101fabb>] ? sub_preempt_count+0x74/0x80 [<c1255c11>] ? _raw_spin_unlock+0xc/0x1f [<c1019bd3>] ? reserve_memtype+0x2e2/0x372 [<c101fabb>] ? sub_preempt_count+0x74/0x80 [<c125474e>] ? schedule+0x689/0x6b1 [<c101eea1>] ? get_parent_ip+0x8/0x19 [<c1017df1>] ? do_page_fault+0x0/0x2fc [<c12566a2>] ? error_code+0x5a/0x60 [<c101007b>] ? speedstep_get_freqs+0xd0/0x11e [<c1017df1>] ? do_page_fault+0x0/0x2fc [<c1105185>] ? iowrite32+0xa/0x29 [<e0d28d38>] ? poke_fb+0x63/0x7b [nouveau] [<e0d28ed3>] ? init_compute_mem+0x110/0x9f3 [nouveau] [<e0d2521c>] ? bios_wr32+0x64/0xc7 [nouveau] [<e0d23f3d>] ? parse_init_table+0xc9/0x192 [nouveau] [<c1253e4b>] ? printk+0xe/0x13 [<e0d2abf5>] ? nouveau_run_vbios_init+0x261/0x310 [nouveau] [<e0d2c078>] ? nouveau_bios_init+0x13d4/0x1708 [nouveau] [<e0d12611>] ? nouveau_card_init+0xbbe/0xee2 [nouveau] [<e0d12da3>] ? nouveau_load+0x46e/0x4a6 [nouveau] [<c116d997>] ? drm_get_pci_dev+0x117/0x1e9 [<c1255e09>] ? _raw_spin_lock_irqsave+0x11/0x2a [<c110fa01>] ? local_pci_probe+0x34/0x74 [<c11100c4>] ? pci_device_probe+0x41/0x63 [<c1178451>] ? driver_probe_device+0x8c/0x110 [<c1178515>] ? __driver_attach+0x40/0x5b [<c1177e66>] ? bus_for_each_dev+0x37/0x5f [<c1178307>] ? driver_attach+0x11/0x13 [<c11784d5>] ? __driver_attach+0x0/0x5b [<c1177941>] ? bus_add_driver+0x8c/0x1bf [<c10fcc63>] ? kset_find_obj+0x4f/0x56 [<e0d79000>] ? nouveau_init+0x0/0x40 [nouveau] [<c1178730>] ? driver_register+0x7a/0xd9 [<e0d79000>] ? nouveau_init+0x0/0x40 [nouveau] [<c1110296>] ? __pci_register_driver+0x33/0x89 [<e0d79000>] ? nouveau_init+0x0/0x40 [nouveau] [<c1001151>] ? do_one_initcall+0x68/0x106 [<c1048c77>] ? sys_init_module+0xbe2/0xdc7 [<c10742ac>] ? sys_close+0x6b/0x9e [<c1002690>] ? sysenter_do_call+0x12/0x26 Warning (Oops_read): Code line not seen, dumping what data is available >>EIP; c1105185 <iowrite32+a/29> <===== Trace; c1254160 <schedule+9b/6b1> Trace; c1022222 <__cond_resched+f/19> Trace; c1254803 <_cond_resched+18/21> Trace; c106535e <unmap_vmas+444/514> Trace; c10682d1 <exit_mmap+99/130> Trace; c1022b23 <mmput+20/94> Trace; c1025d00 <exit_mm+df/e7> Trace; c102718c <do_exit+180/562> Trace; c1255e99 <_raw_spin_trylock+d/4e> Trace; c1025144 <kmsg_dump+7f/f5> Trace; c1004e80 <oops_end+72/75> Trace; c1017bd1 <no_context+10d/116> Trace; c1017df1 <do_page_fault+0/2fc> Trace; c1017cd8 <bad_area_nosemaphore+a/c> Trace; c1017f3d <do_page_fault+14c/2fc> Trace; c101eea1 <get_parent_ip+8/19> Trace; c101fabb <sub_preempt_count+74/80> Trace; c1255c11 <_raw_spin_unlock+c/1f> Trace; c1019bd3 <reserve_memtype+2e2/372> Trace; c101fabb <sub_preempt_count+74/80> Trace; c125474e <schedule+689/6b1> Trace; c101eea1 <get_parent_ip+8/19> Trace; c1017df1 <do_page_fault+0/2fc> Trace; c12566a2 <error_code+5a/60> Trace; c101007b <speedstep_get_freqs+d0/11e> Trace; c1017df1 <do_page_fault+0/2fc> Trace; c1105185 <iowrite32+a/29> Trace; e0d28d38 <END_OF_CODE+1f880d38/????> Trace; e0d28ed3 <END_OF_CODE+1f880ed3/????> Trace; e0d2521c <END_OF_CODE+1f87d21c/????> Trace; e0d23f3d <END_OF_CODE+1f87bf3d/????> Trace; c1253e4b <printk+e/13> Trace; e0d2abf5 <END_OF_CODE+1f882bf5/????> Trace; e0d2c078 <END_OF_CODE+1f884078/????> Trace; e0d12611 <END_OF_CODE+1f86a611/????> Trace; e0d12da3 <END_OF_CODE+1f86ada3/????> Trace; c116d997 <drm_get_pci_dev+117/1e9> Trace; c1255e09 <_raw_spin_lock_irqsave+11/2a> Trace; c110fa01 <local_pci_probe+34/74> Trace; c11100c4 <pci_device_probe+41/63> Trace; c1178451 <driver_probe_device+8c/110> Trace; c1178515 <__driver_attach+40/5b> Trace; c1177e66 <bus_for_each_dev+37/5f> Trace; c1178307 <driver_attach+11/13> Trace; c11784d5 <__driver_attach+0/5b> Trace; c1177941 <bus_add_driver+8c/1bf> Trace; c10fcc63 <kset_find_obj+4f/56> Trace; e0d79000 <END_OF_CODE+1f8d1000/????> Trace; c1178730 <driver_register+7a/d9> Trace; e0d79000 <END_OF_CODE+1f8d1000/????> Trace; c1110296 <__pci_register_driver+33/89> Trace; e0d79000 <END_OF_CODE+1f8d1000/????> Trace; c1001151 <do_one_initcall+68/106> Trace; c1048c77 <sys_init_module+be2/dc7> Trace; c10742ac <sys_close+6b/9e> Trace; c1002690 <sysenter_do_call+12/26> BUG: unable to handle kernel NULL pointer dereference at (null) *pde = 00000000 Oops: 0002 [#2] PREEMPT SMP Pid: 2610, comm: Xorg Tainted: G D 2.6.36-rc2-git1 #81 0880/Pavilion zd7000 (DP761E#ABF) EIP: 0060:[<c1254d67>] EFLAGS: 00013246 CPU: 0 EAX: 00000000 EBX: def83a98 ECX: dedd2040 EDX: dcd5ff14 ESI: dedd2040 EDI: def83a9c EBP: def83aa0 ESP: dcd5ff10 DS: 007b ES: 007b FS: 00d8 GS: 0033 SS: 0068 c1169934 def83aa0 00000000 dedd2040 def83a98 de9a1100 def83a98 de9a1160 <0> c1254c5a de9a1124 de9a1100 c116f60c def83800 de9a1100 de9a115c c1168f8f <0> 00000000 def83a00 def839f8 00003246 deecea80 00000008 deb72238 df879c80 Call Trace: [<c1169934>] ? drm_gem_object_release_handle+0x0/0x24 [<c1254c5a>] ? mutex_lock+0x10/0x1d [<c116f60c>] ? drm_fb_release+0x1b/0x63 [<c1168f8f>] ? drm_release+0x2b7/0x4ae [<c10768ee>] ? fput+0xc6/0x167 [<c107423b>] ? filp_close+0x4e/0x54 [<c10742ac>] ? sys_close+0x6b/0x9e [<c1002690>] ? sysenter_do_call+0x12/0x26 [<c1250000>] ? init_cyrix+0x97/0x3b4 Code: 75 0a 83 7e 18 63 7e 04 f3 90 eb 9e 8d 7b 04 89 f8 e8 d0 10 00 00 8d 6b 08 8b 43 0c 8d 54 24 04 89 53 0c 89 6c 24 04 89 44 24 08 <89> 10 89 74 24 0c 83 c8 ff 87 03 48 74 37 83 c8 ff 87 03 48 74 >>EIP; c1254d67 <__mutex_lock_slowpath+a0/132> <===== Trace; c1169934 <drm_gem_object_release_handle+0/24> Trace; c1254c5a <mutex_lock+10/1d> Trace; c116f60c <drm_fb_release+1b/63> Trace; c1168f8f <drm_release+2b7/4ae> Trace; c10768ee <fput+c6/167> Trace; c107423b <filp_close+4e/54> Trace; c10742ac <sys_close+6b/9e> Trace; c1002690 <sysenter_do_call+12/26> Trace; c1250000 <init_cyrix+97/3b4> Code; c1254d3c <__mutex_lock_slowpath+75/132> 00000000 <_EIP>: Code; c1254d3c <__mutex_lock_slowpath+75/132> 0: 75 0a jne c <_EIP+0xc> Code; c1254d3e <__mutex_lock_slowpath+77/132> 2: 83 7e 18 63 cmpl $0x63,0x18(%esi) Code; c1254d42 <__mutex_lock_slowpath+7b/132> 6: 7e 04 jle c <_EIP+0xc> Code; c1254d44 <__mutex_lock_slowpath+7d/132> 8: f3 90 pause Code; c1254d46 <__mutex_lock_slowpath+7f/132> a: eb 9e jmp ffffffaa <_EIP+0xffffffaa> Code; c1254d48 <__mutex_lock_slowpath+81/132> c: 8d 7b 04 lea 0x4(%ebx),%edi Code; c1254d4b <__mutex_lock_slowpath+84/132> f: 89 f8 mov %edi,%eax Code; c1254d4d <__mutex_lock_slowpath+86/132> 11: e8 d0 10 00 00 call 10e6 <_EIP+0x10e6> Code; c1254d52 <__mutex_lock_slowpath+8b/132> 16: 8d 6b 08 lea 0x8(%ebx),%ebp Code; c1254d55 <__mutex_lock_slowpath+8e/132> 19: 8b 43 0c mov 0xc(%ebx),%eax Code; c1254d58 <__mutex_lock_slowpath+91/132> 1c: 8d 54 24 04 lea 0x4(%esp),%edx Code; c1254d5c <__mutex_lock_slowpath+95/132> 20: 89 53 0c mov %edx,0xc(%ebx) Code; c1254d5f <__mutex_lock_slowpath+98/132> 23: 89 6c 24 04 mov %ebp,0x4(%esp) Code; c1254d63 <__mutex_lock_slowpath+9c/132> 27: 89 44 24 08 mov %eax,0x8(%esp) Code; c1254d67 <__mutex_lock_slowpath+a0/132> <===== 2b: 89 10 mov %edx,(%eax) <===== Code; c1254d69 <__mutex_lock_slowpath+a2/132> 2d: 89 74 24 0c mov %esi,0xc(%esp) Code; c1254d6d <__mutex_lock_slowpath+a6/132> 31: 83 c8 ff or $0xffffffff,%eax Code; c1254d70 <__mutex_lock_slowpath+a9/132> 34: 87 03 xchg %eax,(%ebx) Code; c1254d72 <__mutex_lock_slowpath+ab/132> 36: 48 dec %eax Code; c1254d73 <__mutex_lock_slowpath+ac/132> 37: 74 37 je 70 <_EIP+0x70> Code; c1254d75 <__mutex_lock_slowpath+ae/132> 39: 83 c8 ff or $0xffffffff,%eax Code; c1254d78 <__mutex_lock_slowpath+b1/132> 3c: 87 03 xchg %eax,(%ebx) Code; c1254d7a <__mutex_lock_slowpath+b3/132> 3e: 48 dec %eax Code; c1254d7b <__mutex_lock_slowpath+b4/132> 3f: 74 .byte 0x74 EIP: [<c1254d67>] __mutex_lock_slowpath+0xa0/0x132 SS:ESP 0068:dcd5ff10 CR2: 0000000000000000 Pid: 2610, comm: Xorg Tainted: G D 2.6.36-rc2-git1 #81 Call Trace: [<c1254160>] ? schedule+0x9b/0x6b1 [<c1022222>] ? __cond_resched+0xf/0x19 [<c1254803>] ? _cond_resched+0x18/0x21 [<c106535e>] ? unmap_vmas+0x444/0x514 [<c10682d1>] ? exit_mmap+0x99/0x130 [<c1022b23>] ? mmput+0x20/0x94 [<c1025d00>] ? exit_mm+0xdf/0xe7 [<c102718c>] ? do_exit+0x180/0x562 [<c1255e99>] ? _raw_spin_trylock+0xd/0x4e [<c1025144>] ? kmsg_dump+0x7f/0xf5 [<c1004e80>] ? oops_end+0x72/0x75 [<c1017bd1>] ? no_context+0x10d/0x116 [<c1017df1>] ? do_page_fault+0x0/0x2fc [<c1017cd8>] ? bad_area_nosemaphore+0xa/0xc [<c1017f3d>] ? do_page_fault+0x14c/0x2fc [<c102890b>] ? __do_softirq+0xbc/0xf1 [<c1003b44>] ? do_IRQ+0x81/0x92 [<c1017df1>] ? do_page_fault+0x0/0x2fc [<c12566a2>] ? error_code+0x5a/0x60 [<c1017df1>] ? do_page_fault+0x0/0x2fc [<c1254d67>] ? __mutex_lock_slowpath+0xa0/0x132 [<c1169934>] ? drm_gem_object_release_handle+0x0/0x24 [<c1254c5a>] ? mutex_lock+0x10/0x1d [<c116f60c>] ? drm_fb_release+0x1b/0x63 [<c1168f8f>] ? drm_release+0x2b7/0x4ae [<c10768ee>] ? fput+0xc6/0x167 [<c107423b>] ? filp_close+0x4e/0x54 [<c10742ac>] ? sys_close+0x6b/0x9e [<c1002690>] ? sysenter_do_call+0x12/0x26 [<c1250000>] ? init_cyrix+0x97/0x3b4 Warning (Oops_read): Code line not seen, dumping what data is available >>EIP; c1254d67 <__mutex_lock_slowpath+a0/132> <===== Trace; c1254160 <schedule+9b/6b1> Trace; c1022222 <__cond_resched+f/19> Trace; c1254803 <_cond_resched+18/21> Trace; c106535e <unmap_vmas+444/514> Trace; c10682d1 <exit_mmap+99/130> Trace; c1022b23 <mmput+20/94> Trace; c1025d00 <exit_mm+df/e7> Trace; c102718c <do_exit+180/562> Trace; c1255e99 <_raw_spin_trylock+d/4e> Trace; c1025144 <kmsg_dump+7f/f5> Trace; c1004e80 <oops_end+72/75> Trace; c1017bd1 <no_context+10d/116> Trace; c1017df1 <do_page_fault+0/2fc> Trace; c1017cd8 <bad_area_nosemaphore+a/c> Trace; c1017f3d <do_page_fault+14c/2fc> Trace; c102890b <__do_softirq+bc/f1> Trace; c1003b44 <do_IRQ+81/92> Trace; c1017df1 <do_page_fault+0/2fc> Trace; c12566a2 <error_code+5a/60> Trace; c1017df1 <do_page_fault+0/2fc> Trace; c1254d67 <__mutex_lock_slowpath+a0/132> Trace; c1169934 <drm_gem_object_release_handle+0/24> Trace; c1254c5a <mutex_lock+10/1d> Trace; c116f60c <drm_fb_release+1b/63> Trace; c1168f8f <drm_release+2b7/4ae> Trace; c10768ee <fput+c6/167> Trace; c107423b <filp_close+4e/54> Trace; c10742ac <sys_close+6b/9e> Trace; c1002690 <sysenter_do_call+12/26> Trace; c1250000 <init_cyrix+97/3b4> 3 warnings and 1 error issued. Results may not be reliable.
_______________________________________________ dri-devel mailing list dri-devel@xxxxxxxxxxxxxxxxxxxxx http://lists.freedesktop.org/mailman/listinfo/dri-devel