https://bugs.freedesktop.org/show_bug.cgi?id=29384 --- Comment #5 from peterle@xxxxxxxxxxxxxxxxx 2010-08-03 11:08:15 PDT --- Thank you for your help. But the answer is "No". I doesn't fix the slow resuspend (instead it feels slower, no wonder...) and also not the slow TTY-Switch between the terminals if /def/fb* is used. Both problems still exist. To be honestly. Making a delay just longer doesn't look like a well solution. Here is my dmesg output, maybe it helps (last lines): PM: early resume of devices complete after 0.753 msecs ehci_hcd 0000:00:1a.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 ehci_hcd 0000:00:1a.0: setting latency timer to 64 HDA Intel 0000:00:1b.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22 HDA Intel 0000:00:1b.0: setting latency timer to 64 ehci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23 pci 0000:00:1e.0: setting latency timer to 64 ehci_hcd 0000:00:1d.0: setting latency timer to 64 HDA Intel 0000:00:1b.0: irq 45 for MSI/MSI-X ahci 0000:00:1f.2: setting latency timer to 64 pci 0000:00:1f.3: PCI INT C -> GSI 18 (level, low) -> IRQ 18 radeon 0000:02:00.0: setting latency timer to 64 HDA Intel 0000:02:00.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17 HDA Intel 0000:02:00.1: setting latency timer to 64 ath9k 0000:05:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17 HDA Intel 0000:02:00.1: irq 46 for MSI/MSI-X sd 0:0:0:0: [sda] Starting disk [drm] Clocks initialized ! [drm] ring test succeeded in 1 usecs [drm] ib test succeeded in 0 usecs usb 2-1.5: reset high speed USB device using ehci_hcd and address 3 ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) ata1.00: configured for UDMA/133 [drm:atom_op_jump] *ERROR* atombios stuck in loop for more than 5secs aborting [drm:atom_execute_table_locked] *ERROR* atombios stuck executing CB5A (len 67, WS 0, PS 0) @ 0xCB89 PM: resume of devices complete after 7531.240 msecs Restarting tasks ... done. video LNXVIDEO:00: Restoring backlight state [ pm_notifier_block : 170 ] event :4 atl1c 0000:03:00.0: irq 47 for MSI/MSI-X ADDRCONF(NETDEV_UP): eth0: link is not ready ADDRCONF(NETDEV_UP): wlan0: link is not ready EXT4-fs (sda1): re-mounted. Opts: commit=0 EXT4-fs (sda2): re-mounted. Opts: commit=0 ath9k: Two wiphys trying to scan at the same time ath9k: Two wiphys trying to scan at the same time wlan0: deauthenticating from 00:1c:10:36:48:42 by local choice (reason=3) wlan0: authenticate with 00:1c:10:36:48:42 (try 1) wlan0: authenticated wlan0: associate with 00:1c:10:36:48:42 (try 1) wlan0: RX AssocResp from 00:1c:10:36:48:42 (capab=0x431 status=0 aid=1) wlan0: associated ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready wlan0: no IPv6 routers present -- Configure bugmail: https://bugs.freedesktop.org/userprefs.cgi?tab=email ------- You are receiving this mail because: ------- You are the assignee for the bug. _______________________________________________ dri-devel mailing list dri-devel@xxxxxxxxxxxxxxxxxxxxx http://lists.freedesktop.org/mailman/listinfo/dri-devel
