[PATCH V2] dt-bindings: dma: fsl-edma: Convert to DT schema

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



From: Peng Fan <peng.fan@xxxxxxx>

Convert the eDMA controller binding to DT schema.

Signed-off-by: Peng Fan <peng.fan@xxxxxxx>
---

V2:
 Typo fix
 Correct interrupts/interrupt-names/AllOf

 .../devicetree/bindings/dma/fsl,edma.yaml     | 140 ++++++++++++++++++
 .../devicetree/bindings/dma/fsl-edma.txt      | 111 --------------
 2 files changed, 140 insertions(+), 111 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/dma/fsl,edma.yaml
 delete mode 100644 Documentation/devicetree/bindings/dma/fsl-edma.txt

diff --git a/Documentation/devicetree/bindings/dma/fsl,edma.yaml b/Documentation/devicetree/bindings/dma/fsl,edma.yaml
new file mode 100644
index 000000000000..0a63b0b70f98
--- /dev/null
+++ b/Documentation/devicetree/bindings/dma/fsl,edma.yaml
@@ -0,0 +1,140 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/dma/fsl,edma.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Freescale enhanced Direct Memory Access(eDMA) Controller
+
+description: |
+  The eDMA channels have multiplex capability by programmable
+  memory-mapped registers. channels are split into two groups, called
+  DMAMUX0 and DMAMUX1, specific DMA request source can only be multiplexed
+  by any channel of certain group, DMAMUX0 or DMAMUX1, but not both.
+
+maintainers:
+  - Peng Fan <peng.fan@xxxxxxx>
+
+properties:
+  compatible:
+    oneOf:
+      - enum:
+          - fsl,vf610-edma
+          - fsl,imx7ulp-edma
+      - items:
+          - const: fsl,ls1028a-edma
+          - const: fsl,vf610-edma
+
+  "#dma-cells":
+    const: 2
+
+  dma-channels:
+    const: 32
+
+  clocks:
+    maxItems: 2
+
+  big-endian:
+    description: |
+      If present registers and hardware scatter/gather descriptors of the
+      eDMA are implemented in big endian mode, otherwise in little mode.
+    type: boolean
+
+required:
+  - "#dma-cells"
+  - compatible
+  - reg
+  - interrupts
+  - clocks
+  - dma-channels
+
+allOf:
+  - $ref: "dma-controller.yaml#"
+  - if:
+      properties:
+        compatible:
+          contains:
+            const: fsl,vf610-edma
+    then:
+      properties:
+        clock-names:
+          items:
+            - const: dmamux0
+            - const: dmamux1
+        interrupts:
+          maxItems: 2
+        interrupt-names:
+          items:
+            - const: edma-tx
+            - const: edma-err
+        reg:
+          maxItems: 3
+
+  - if:
+      properties:
+        compatible:
+          contains:
+            const: fsl,imx7ulp-edma
+    then:
+      properties:
+        clock-names:
+          items:
+            - const: dma
+            - const: dmamux0
+        interrupts:
+          maxItems: 17
+        reg:
+          maxItems: 2
+
+unevaluatedProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/interrupt-controller/arm-gic.h>
+    #include <dt-bindings/clock/vf610-clock.h>
+
+    edma0: dma-controller@40018000 {
+      #dma-cells = <2>;
+      compatible = "fsl,vf610-edma";
+      reg = <0x40018000 0x2000>,
+            <0x40024000 0x1000>,
+            <0x40025000 0x1000>;
+      interrupts = <0 8 IRQ_TYPE_LEVEL_HIGH>,
+                   <0 9 IRQ_TYPE_LEVEL_HIGH>;
+      interrupt-names = "edma-tx", "edma-err";
+      dma-channels = <32>;
+      clock-names = "dmamux0", "dmamux1";
+      clocks = <&clks VF610_CLK_DMAMUX0>, <&clks VF610_CLK_DMAMUX1>;
+    };
+
+  - |
+    #include <dt-bindings/interrupt-controller/arm-gic.h>
+    #include <dt-bindings/clock/imx7ulp-clock.h>
+
+    edma1: dma-controller@40080000 {
+      #dma-cells = <2>;
+      compatible = "fsl,imx7ulp-edma";
+      reg = <0x40080000 0x2000>,
+            <0x40210000 0x1000>;
+      dma-channels = <32>;
+      interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>,
+                   <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>,
+                   <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>,
+                   <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>,
+                   <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>,
+                   <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>,
+                   <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>,
+                   <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>,
+                   <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>,
+                   <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>,
+                   <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>,
+                   <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>,
+                   <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>,
+                   <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>,
+                   <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>,
+                   <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>,
+                   /* last is eDMA2-ERR interrupt */
+                   <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>;
+       clock-names = "dma", "dmamux0";
+       clocks = <&pcc2 IMX7ULP_CLK_DMA1>, <&pcc2 IMX7ULP_CLK_DMA_MUX1>;
+    };
diff --git a/Documentation/devicetree/bindings/dma/fsl-edma.txt b/Documentation/devicetree/bindings/dma/fsl-edma.txt
deleted file mode 100644
index ee1754739b4b..000000000000
--- a/Documentation/devicetree/bindings/dma/fsl-edma.txt
+++ /dev/null
@@ -1,111 +0,0 @@
-* Freescale enhanced Direct Memory Access(eDMA) Controller
-
-  The eDMA channels have multiplex capability by programmble memory-mapped
-registers. channels are split into two groups, called DMAMUX0 and DMAMUX1,
-specific DMA request source can only be multiplexed by any channel of certain
-group, DMAMUX0 or DMAMUX1, but not both.
-
-* eDMA Controller
-Required properties:
-- compatible :
-	- "fsl,vf610-edma" for eDMA used similar to that on Vybrid vf610 SoC
-	- "fsl,imx7ulp-edma" for eDMA2 used similar to that on i.mx7ulp
-	- "fsl,ls1028a-edma" followed by "fsl,vf610-edma" for eDMA used on the
-	  LS1028A SoC.
-- reg : Specifies base physical address(s) and size of the eDMA registers.
-	The 1st region is eDMA control register's address and size.
-	The 2nd and the 3rd regions are programmable channel multiplexing
-	control register's address and size.
-- interrupts : A list of interrupt-specifiers, one for each entry in
-	interrupt-names on vf610 similar SoC. But for i.mx7ulp per channel
-	per transmission interrupt, total 16 channel interrupt and 1
-	error interrupt(located in the last), no interrupt-names list on
-	i.mx7ulp for clean on dts.
-- #dma-cells : Must be <2>.
-	The 1st cell specifies the DMAMUX(0 for DMAMUX0 and 1 for DMAMUX1).
-	Specific request source can only be multiplexed by specific channels
-	group called DMAMUX.
-	The 2nd cell specifies the request source(slot) ID.
-	See the SoC's reference manual for all the supported request sources.
-- dma-channels : Number of channels supported by the controller
-- clock-names : A list of channel group clock names. Should contain:
-	"dmamux0" - clock name of mux0 group
-	"dmamux1" - clock name of mux1 group
-	Note: No dmamux0 on i.mx7ulp, but another 'dma' clk added on i.mx7ulp.
-- clocks : A list of phandle and clock-specifier pairs, one for each entry in
-	clock-names.
-
-Optional properties:
-- big-endian: If present registers and hardware scatter/gather descriptors
-	of the eDMA are implemented in big endian mode, otherwise in little
-	mode.
-- interrupt-names : Should contain the below on vf610 similar SoC but not used
-	on i.mx7ulp similar SoC:
-	"edma-tx" - the transmission interrupt
-	"edma-err" - the error interrupt
-
-
-Examples:
-
-edma0: dma-controller@40018000 {
-	#dma-cells = <2>;
-	compatible = "fsl,vf610-edma";
-	reg = <0x40018000 0x2000>,
-		<0x40024000 0x1000>,
-		<0x40025000 0x1000>;
-	interrupts = <0 8 IRQ_TYPE_LEVEL_HIGH>,
-		<0 9 IRQ_TYPE_LEVEL_HIGH>;
-	interrupt-names = "edma-tx", "edma-err";
-	dma-channels = <32>;
-	clock-names = "dmamux0", "dmamux1";
-	clocks = <&clks VF610_CLK_DMAMUX0>,
-		<&clks VF610_CLK_DMAMUX1>;
-}; /* vf610 */
-
-edma1: dma-controller@40080000 {
-	#dma-cells = <2>;
-	compatible = "fsl,imx7ulp-edma";
-	reg = <0x40080000 0x2000>,
-		<0x40210000 0x1000>;
-	dma-channels = <32>;
-	interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>,
-		     <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>,
-		     <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>,
-		     <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>,
-		     <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>,
-		     <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>,
-		     <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>,
-		     <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>,
-		     <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>,
-		     <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>,
-		     <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>,
-		     <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>,
-		     <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>,
-		     <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>,
-		     <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>,
-		     <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>,
-		     /* last is eDMA2-ERR interrupt */
-		     <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>;
-	clock-names = "dma", "dmamux0";
-	clocks = <&pcc2 IMX7ULP_CLK_DMA1>,
-		 <&pcc2 IMX7ULP_CLK_DMA_MUX1>;
-}; /* i.mx7ulp */
-
-* DMA clients
-DMA client drivers that uses the DMA function must use the format described
-in the dma.txt file, using a two-cell specifier for each channel: the 1st
-specifies the channel group(DMAMUX) in which this request can be multiplexed,
-and the 2nd specifies the request source.
-
-Examples:
-
-sai2: sai@40031000 {
-	compatible = "fsl,vf610-sai";
-	reg = <0x40031000 0x1000>;
-	interrupts = <0 86 IRQ_TYPE_LEVEL_HIGH>;
-	clock-names = "sai";
-	clocks = <&clks VF610_CLK_SAI2>;
-	dma-names = "tx", "rx";
-	dmas = <&edma0 0 21>,
-		<&edma0 0 20>;
-};
-- 
2.25.1




[Index of Archives]     [Linux Kernel]     [Linux ARM (vger)]     [Linux ARM MSM]     [Linux Omap]     [Linux Arm]     [Linux Tegra]     [Fedora ARM]     [Linux for Samsung SOC]     [eCos]     [Linux PCI]     [Linux Fastboot]     [Gcc Help]     [Git]     [DCCP]     [IETF Announce]     [Security]     [Linux MIPS]     [Yosemite Campsites]

  Powered by Linux