Re: [PATCH V2 1/2] bindings: fsl-imx-sdma: Document 'HDMI Audio' transfer

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On 24/05/2022 10:03, Joy Zou wrote:
> Add HDMI Audio transfer type.
> 
> convert the sdma bindings txt into yaml in v2.
> 
> Signed-off-by: Joy Zou <joy.zou@xxxxxxx>
> ---
> Changes since v1:
> convert the sdma bindings txt into yaml in v2.
> ---
>  .../devicetree/bindings/dma/fsl-imx-sdma.yaml | 135 ++++++++++++++++++

There is no conversion here, only new file...

>  1 file changed, 135 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/dma/fsl-imx-sdma.yaml
> 
> diff --git a/Documentation/devicetree/bindings/dma/fsl-imx-sdma.yaml b/Documentation/devicetree/bindings/dma/fsl-imx-sdma.yaml
> new file mode 100644
> index 000000000000..5b4f7a09a395
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/dma/fsl-imx-sdma.yaml

Filename: fsl,imx-sdma.yaml

> @@ -0,0 +1,135 @@
> +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/dma/fsl-imx-sdma.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: Freescale Smart Direct Memory Access (SDMA) Controller for i.MX
> +
> +maintainers:
> +  - Vinod Koul <vkoul@xxxxxxxxxx>

This should not be subsystem maintainer but someone closer to the actual
device.

> +
> +allOf:
> +  - $ref: "dma-controller.yaml#"
> +
> +# Everything else is described in the common file

Skip the comment please.

> +
> +properties:
> +  compatible:
> +    items:
> +      - enum:
> +          - fsl,imx25-sdma
> +          - fsl,imx31-sdma
> +          - fsl,imx31-to1-sdma
> +          - fsl,imx31-to2-sdma
> +          - fsl,imx35-to1-sdma
> +          - fsl,imx35-to2-sdma
> +          - fsl,imx51-sdma
> +          - fsl,imx53-sdma
> +          - fsl,imx6q-sdma
> +          - fsl,imx7d-sdma
> +          - fsl,imx6sx-sdma
> +          - fsl,imx6ul-sdma
> +          - fsl,imx8mm-sdma
> +          - fsl,imx8mn-sdma
> +          - fsl,imx8mp-sdma
> +      - enum:
> +          - fsl,imx35-sdma
> +          - fsl,imx8mq-sdma

No, fallback cannot be variable. I doubt that
fsl,imx25-sdma+fsl,imx8mq-sdma makes any sense!

Additionally, this does not match existing DTS. Please run `make
dtbs_check`.

> +
> +  reg:
> +    description: Should contain SDMA registers location and length

Skip description. Uou need to add maxItems

> +
> +  interrupts:
> +    description: Should contain SDMA interrupt

Skip description. Uou need to add maxItems


> +
> +  fsl,sdma-ram-script-name:
> +    $ref: /schemas/types.yaml#/definitions/string
> +    description: Should contain the full path of SDMA RAM scripts firmware.
> +
> +  "#dma-cells":
> +    const: 3
> +    description: |
> +      The first cell: request/event ID
> +
> +      The second cell: peripheral types ID
> +        enum:
> +          - MCU domain SSI: 0
> +          - Shared SSI: 1
> +          - MMC: 2
> +          - SDHC: 3
> +          - MCU domain UART: 4
> +          - Shared UART: 5
> +          - FIRI: 6
> +          - MCU domain CSPI: 7
> +          - Shared CSPI: 8
> +          - SIM: 9
> +          - ATA: 10
> +          - CCM: 11
> +          - External peripheral: 12
> +          - Memory Stick Host Controller: 13
> +          - Shared Memory Stick Host Controller: 14
> +          - DSP: 15
> +          - Memory: 16
> +          - FIFO type Memory: 17
> +          - SPDIF: 18
> +          - IPU Memory: 19
> +          - ASRC: 20
> +          - ESAI: 21
> +          - SSI Dual FIFO: 22
> +              description: needs firmware more than ver 2> +          - Shared ASRC: 23
> +          - SAI: 24
> +          - HDMI Audio: 25
> +
> +       The third cell: transfer priority ID
> +         enum:
> +           - High: 0
> +           - Medium: 1
> +           - Low: 2
> +
> +  gpr:
> +    description: The phandle to the General Purpose Register (GPR) node

type/ref needed

> +
> +  fsl,sdma-event-remap:
> +    $ref: /schemas/types.yaml#/definitions/uint32-array
> +    description: |
> +      Register bits of sdma event remap, the format is <reg shift val>.
> +      - reg: the GPR register offset
> +      - shift: the bit position inside the GPR register
> +      - val: the value of the bit (0 or 1)

Need maxItems or items with description.

> +
> +required:
> +  - compatible
> +  - reg
> +  - interrupts
> +  - fsl,sdma-ram-script-name
> +  - "#dma-cells"
> +
> +unevaluatedProperties: false
> +
> +examples:
> +  - |
> +    sdma: dma-controller@83fb0000 {
> +      compatible = "fsl,imx51-sdma", "fsl,imx35-sdma";
> +      reg = <0x83fb0000 0x4000>;
> +      interrupts = <6>;
> +      #dma-cells = <3>;
> +      fsl,sdma-ram-script-name = "sdma-imx51.bin";
> +    };
> +
> +#DMA clients connected to the i.MX SDMA controller must use the format
> +#described in the dma-controller.yaml file.
> +  - |
> +    ssi2: ssi@70014000 {

Skip consumer example, it's obvious.

> +      compatible = "fsl,imx51-ssi", "fsl,imx21-ssi";
> +      reg = <0x70014000 0x4000>;
> +      interrupts = <30>;
> +      clocks = <&clks 49>;
> +      dmas = <&sdma 24 1 0>,
> +             <&sdma 25 1 0>;
> +      dma-names = "rx", "tx";
> +      fsl,fifo-depth = <15>;
> +    };
> +
> +...


Best regards,
Krzysztof



[Index of Archives]     [Linux Kernel]     [Linux ARM (vger)]     [Linux ARM MSM]     [Linux Omap]     [Linux Arm]     [Linux Tegra]     [Fedora ARM]     [Linux for Samsung SOC]     [eCos]     [Linux PCI]     [Linux Fastboot]     [Gcc Help]     [Git]     [DCCP]     [IETF Announce]     [Security]     [Linux MIPS]     [Yosemite Campsites]

  Powered by Linux