On 28/02/22 2:52 pm, Vignesh Raghavendra wrote:
> Hi Peter,
>
> On 21/02/22 1:42 am, Péter Ujfalusi wrote:
>> Hi Vignesh,
>>
>> On 15/02/2022 06:41, Vignesh Raghavendra wrote:
>>> In cyclic mode, there is no additional descriptor pushed to collect
>>> outstanding data on channel teardown. Therefore no need to wait for this
>>> descriptor to come back.
>>>
>>> Without this terminating aplay cmd outputs false error msg like:
>>> [ 116.402800] ti-bcdma 485c0100.dma-controller: chan1 teardown timeout!
>>
>> are you sure it is aplay? It is MEM_TO_DEV, we only use the flush
>> descriptor for DEV_TO_MEM. MEM_TO_DEV can 'disconnect' from the
>> peripheral to flush out the FIFO.
>>
>
> Yes, this is with aplay. You are right that MEM_TO_DEV should have
> worked w/o this patch.
>
>
>> I have not seen this on am654, j721e. I can not recall seeing this on
>> the capture side either.
>>
>
> I dont see it either
>
>> The cyclic TR should be able to drain the DEV_TO_MEM by itself and the
>> TR should terminate.
>>
>
> You are right. There seems to be a trobule with McASP + BCDMA on AM62
> which needs more investigation. I see
>
> RT c0000000 peer RT 90000000
> BCNT 5dc00, peer BCNT 46400
>
> So there is some data stuck in pipe which prevents channel from
> disabling and TDCM being signaled. My guess is McASP is no longer
> requesting more data from PDMA. Any way to look at McASP FIFO state/ DMA
> req enable state? Wondering what else can prevent draining of data.
>
> One difference is that AM62 has ti,tlv320aic3106 codec (codec is the
> master) where J7 uses PCM.
>
I see couple of issues with DMA usage by McASP/sound:
McASP TX FIFO events are disabled first and then DMA channel is stopped.
This does not work for K3 SoCs as some data remains stuck in DMA pipe
and channel never goes to disable state.
I see .stop_dma_first flag in snd_soc_dai_link to force DMA to be
stopped first, but I am not quite familiar on where to set this flag?
Even so, snd_dmaengine_pcm_trigger() calls dmaengine_terminate_async()
and does not call dmaengine_synchronize() before disabling McASP TX, so
channel teardown would still be unsuccessful.
Alternately, we could reduce dev_warn() in udma_synchronize() to
dev_dbg() as channel is still recoverable via udma_reset_chan() which
is done immediately after.
There is a further dev_warn() message to indicate if channel refused to
stop even after a reset?
Regards
Vignesh
> Regards
> Vignesh
>
>
>>
>>> Signed-off-by: Vignesh Raghavendra <vigneshr@xxxxxx>
>>> ---
>>> drivers/dma/ti/k3-udma.c | 2 +-
>>> 1 file changed, 1 insertion(+), 1 deletion(-)
>>>
>>> diff --git a/drivers/dma/ti/k3-udma.c b/drivers/dma/ti/k3-udma.c
>>> index 9abb08d353ca0..c9a1b2f312603 100644
>>> --- a/drivers/dma/ti/k3-udma.c
>>> +++ b/drivers/dma/ti/k3-udma.c
>>> @@ -3924,7 +3924,7 @@ static void udma_synchronize(struct dma_chan *chan)
>>>
>>> vchan_synchronize(&uc->vc);
>>>
>>> - if (uc->state == UDMA_CHAN_IS_TERMINATING) {
>>> + if (uc->state == UDMA_CHAN_IS_TERMINATING && !uc->cyclic) {
>>> timeout = wait_for_completion_timeout(&uc->teardown_completed,
>>> timeout);
>>> if (!timeout) {
>>
