Re: [PATCH v9 1/2] dt-bindings: dma: Add bindings for Intel LGM SoC

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Hi Vinod,

Thanks for your valuable review. My comments inline.

On 11/21/2020 8:19 PM, Vinod Koul wrote:
On 20-11-20, 19:30, Reddy, MallikarjunaX wrote:
Hi Vinod,
Thanks for the review. My comments inline.

On 11/18/2020 11:55 PM, Vinod Koul wrote:
On 12-11-20, 13:38, Amireddy Mallikarjuna reddy wrote:
Add DT bindings YAML schema for DMA controller driver
of Lightning Mountain (LGM) SoC.

Signed-off-by: Amireddy Mallikarjuna reddy <mallikarjunax.reddy@xxxxxxxxxxxxxxx>
---
v1:
- Initial version.

v2:
- Fix bot errors.

v3:
- No change.

v4:
- Address Thomas langer comments
    - use node name pattern as dma-controller as in common binding.
    - Remove "_" (underscore) in instance name.
    - Remove "port-" and "chan-" in attribute name for both 'dma-ports' & 'dma-channels' child nodes.

v5:
- Moved some of the attributes in 'dma-ports' & 'dma-channels' child nodes to dma client/consumer side as cells in 'dmas' properties.

v6:
- Add additionalProperties: false
- completely removed 'dma-ports' and 'dma-channels' child nodes.
- Moved channel dt properties to client side dmas.
- Use standard dma-channels and dma-channel-mask properties.
- Documented reset-names
- Add description for dma-cells

v7:
- modified compatible to oneof
- Reduced number of dma-cells to 3
- Fine tune the description of some properties.

v7-resend:
- rebase to 5.10-rc1

v8:
- rebased to 5.10-rc3
- Fixing the bot issues (wrong indentation)

v9:
- rebased to 5.10-rc3
- Use 'enum' instead of oneOf+const
- Drop '#dma-cells' in required:, already covered in dma-common.yaml
- Drop nodename Already covered by dma-controller.yaml
---
   .../devicetree/bindings/dma/intel,ldma.yaml        | 130 +++++++++++++++++++++
   1 file changed, 130 insertions(+)
   create mode 100644 Documentation/devicetree/bindings/dma/intel,ldma.yaml

diff --git a/Documentation/devicetree/bindings/dma/intel,ldma.yaml b/Documentation/devicetree/bindings/dma/intel,ldma.yaml
new file mode 100644
index 000000000000..c06281a10178
--- /dev/null
+++ b/Documentation/devicetree/bindings/dma/intel,ldma.yaml
@@ -0,0 +1,130 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/dma/intel,ldma.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Lightning Mountain centralized low speed DMA and high speed DMA controllers.
+
+maintainers:
+  - chuanhua.lei@xxxxxxxxx
+  - mallikarjunax.reddy@xxxxxxxxx
+
+allOf:
+  - $ref: "dma-controller.yaml#"
+
+properties:
+  compatible:
+    enum:
+      - intel,lgm-cdma
+      - intel,lgm-dma2tx
+      - intel,lgm-dma1rx
+      - intel,lgm-dma1tx
+      - intel,lgm-dma0tx
+      - intel,lgm-dma3
+      - intel,lgm-toe-dma30
+      - intel,lgm-toe-dma31
+
+  reg:
+    maxItems: 1
+
+  "#dma-cells":
+    const: 3
+    description:
+      The first cell is the peripheral's DMA request line.
+      The second cell is the peripheral's (port) number corresponding to the channel.
+      The third cell is the burst length of the channel.
+
+  dma-channels:
+    minimum: 1
+    maximum: 16
+
+  dma-channel-mask:
+    maxItems: 1
+
+  clocks:
+    maxItems: 1
+
+  resets:
+    maxItems: 1
+
+  reset-names:
+    items:
+      - const: ctrl
+
+  interrupts:
+    maxItems: 1
+
+  intel,dma-poll-cnt:
+    $ref: /schemas/types.yaml#definitions/uint32
+    description:
+      DMA descriptor polling counter is used to control the poling mechanism
s/poling/polling
Ok, Thanks.
+      for the descriptor fetching for all channels.
+
+  intel,dma-byte-en:
+    type: boolean
+    description:
+      DMA byte enable is only valid for DMA write(RX).
+      Byte enable(1) means DMA write will be based on the number of dwords
+      instead of the whole burst.
Can you explain this, also sounds you could use _maxburst values..?
when dma-byte-en = 0 (disabled) DMA write will be in terms of burst length,
dma-byte-en = 1 (enabled) write will be in terms of Dwords.

Byte enable = 0 (Disabled) means that DMA write will be based on the burst
length, even if it only transmits one byte.
Byte enable = 1(enabled) means that DMA write will be based on the number of
Dwords, instead of the whole burst.
Sounds like a hw property or is this configurable to engine..?
Yes its hw property. Not configurable to engine.
+
+  intel,dma-drb:
+    type: boolean
+    description:
+      DMA descriptor read back to make sure data and desc synchronization.
+
+  intel,dma-desc-in-sram:
+    type: boolean
+    description:
+      DMA descritpors in SRAM or not. Some old controllers descriptors
+      can be in DRAM or SRAM. The new ones are all in SRAM.
should that not be decided by driver..? Or is this a hw property?
This is DMA controller capability. It can be decided from driver also. i
will change accordingly.
+
+  intel,dma-orrc:
+    $ref: /schemas/types.yaml#definitions/uint32
+    description:
+      DMA outstanding read counter value determine the number of
+      ORR-Outstanding Read Request. The maximum value is 16.
How would this be used by folks..?
A register bit will be used to enable/disable the ORR feature.

Outstanding Read Capability introduce CMD FIFO to support up to 16
outstanding reads for different packet in same channel.

For large packets up to 16 OR can be issued, the number of OR is
configurable.
How will configure this and when..?

This is DMA (ver > DMA_VER22) hw capability and is configured from device tree.

If this property is not present or count is zero means orrc capability is disabled. If orrc count is 4 <= orr_cnt < 16 then write the enable bit and value to corresponding register.

Ex:
        if (d->orrc > 0 && d->orrc <= DMA_ORRC_MAX_CNT)
                val = DMA_ORRC_EN | FIELD_PREP(DMA_ORRC_ORRCNT, d->orrc);

        ldma_update_bits(d, mask, val, DMA_ORRC);

This hw capability supports dma instances ver > DMA_VER22.

+
+  intel,dma-dburst-wr:
+    type: boolean
+    description:
+      Enable RX dynamic burst write. When it is enabled, the DMA does RX dynamic burst;
+      if it is disabled, the DMA RX will still support programmable fixed burst size of 2,4,8,16.
+      It only applies to RX DMA and memcopy DMA.
+
+required:
+  - compatible
+  - reg
So only two are mandatory, what about the bunch of intel properties you
added above..?
Some of the properties are DMA capabilities, Enabling from device tree.
other properties will use default values from driver if we dont pass it from
device tree.




[Index of Archives]     [Linux Kernel]     [Linux ARM (vger)]     [Linux ARM MSM]     [Linux Omap]     [Linux Arm]     [Linux Tegra]     [Fedora ARM]     [Linux for Samsung SOC]     [eCos]     [Linux PCI]     [Linux Fastboot]     [Gcc Help]     [Git]     [DCCP]     [IETF Announce]     [Security]     [Linux MIPS]     [Yosemite Campsites]

  Powered by Linux