Re: [PATCH v2 4/6] dmaengine: dw: Print warning if multi-block is unsupported

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Mon, May 11, 2020 at 10:32:55PM +0300, Serge Semin wrote:
> On Mon, May 11, 2020 at 04:58:53PM +0300, Andy Shevchenko wrote:
> > On Mon, May 11, 2020 at 4:48 PM Serge Semin
> > <Sergey.Semin@xxxxxxxxxxxxxxxxxxxx> wrote:
> > >
> > > On Mon, May 11, 2020 at 12:58:13PM +0100, Mark Brown wrote:
> > > > On Mon, May 11, 2020 at 05:10:16AM +0300, Serge Semin wrote:
> > > >
> > > > > Alas linearizing the SPI messages won't help in this case because the DW DMA
> > > > > driver will split it into the max transaction chunks anyway.
> > > >
> > > > That sounds like you need to also impose a limit on the maximum message
> > > > size as well then, with that you should be able to handle messages up
> > > > to whatever that limit is.  There's code for that bit already, so long
> > > > as the limit is not too low it should be fine for most devices and
> > > > client drivers can see the limit so they can be updated to work with it
> > > > if needed.
> > >
> > > Hmm, this might work. The problem will be with imposing such limitation through
> > > the DW APB SSI driver. In order to do this I need to know:
> > > 1) Whether multi-block LLP is supported by the DW DMA controller.
> > > 2) Maximum DW DMA transfer block size.
> > > Then I'll be able to use this information in the can_dma() callback to enable
> > > the DMA xfers only for the safe transfers. Did you mean something like this when
> > > you said "There's code for that bit already" ? If you meant the max_dma_len
> > > parameter, then setting it won't work, because it just limits the SG items size
> > > not the total length of a single transfer.
> > >
> > > So the question is of how to export the multi-block LLP flag from DW DMAc
> > > driver. Andy?
> > 
> > I'm not sure I understand why do you need this being exported. Just
> > always supply SG list out of single entry and define the length
> > according to the maximum segment size (it's done IIRC in SPI core).
> 
> Finally I see your point. So you suggest to feed the DMA engine with SG list
> entries one-by-one instead of sending all of them at once in a single
> dmaengine_prep_slave_sg() -> dmaengine_submit() -> dma_async_issue_pending()
> session. Hm, this solution will work, but there is an issue. There is no
> guarantee, that Tx and Rx SG lists are symmetric, consisting of the same
> number of items with the same sizes. It depends on the Tx/Rx buffers physical
> address alignment and their offsets within the memory pages. Though this
> problem can be solved by making the Tx and Rx SG lists symmetric. I'll have
> to implement a clever DMA IO loop, which would extract the DMA
> addresses/lengths from the SG entries and perform the single-buffer DMA 
> transactions with the DMA buffers of the same length.
> 
> Regarding noLLP being exported. Obviously I intended to solve the problem in a
> generic way since the problem is common for noLLP DW APB SSI/DW DMAC combination.
> In order to do this we need to know whether the multi-block LLP feature is
> unsupported by the DW DMA controller. We either make such info somehow exported
> from the DW DMA driver, so the DMA clients (like Dw APB SSI controller driver)
> could be ready to work around the problem; or just implement a flag-based quirk
> in the DMA client driver, which would be enabled in the platform-specific basis
> depending on the platform device actually detected (for instance, a specific
> version of the DW APB SSI IP). AFAICS You'd prefer the later option. 

So, we may extend the struct of DMA parameters to tell the consumer amount of entries (each of which is no longer than maximum segment size) it can afford:
- 0: Auto (DMA driver handles any cases itself)
- 1: Only single entry
- 2: Up to two...


-- 
With Best Regards,
Andy Shevchenko





[Index of Archives]     [Linux Kernel]     [Linux ARM (vger)]     [Linux ARM MSM]     [Linux Omap]     [Linux Arm]     [Linux Tegra]     [Fedora ARM]     [Linux for Samsung SOC]     [eCos]     [Linux PCI]     [Linux Fastboot]     [Gcc Help]     [Git]     [DCCP]     [IETF Announce]     [Security]     [Linux MIPS]     [Yosemite Campsites]

  Powered by Linux