On Fri, Sep 27, 2019 at 06:48:29AM +0000, Radhey Shyam Pandey wrote: > > -----Original Message----- > > From: Vinod Koul <vkoul@xxxxxxxxxx> > > Sent: Thursday, September 26, 2019 10:51 PM > > To: Radhey Shyam Pandey <radheys@xxxxxxxxxx> > > Cc: dan.j.williams@xxxxxxxxx; Michal Simek <michals@xxxxxxxxxx>; > > nick.graumann@xxxxxxxxx; andrea.merello@xxxxxxxxx; Appana Durga > > Kedareswara Rao <appanad@xxxxxxxxxx>; mcgrof@xxxxxxxxxx; > > dmaengine@xxxxxxxxxxxxxxx; linux-kernel@xxxxxxxxxxxxxxx > > Subject: Re: [PATCH -next 7/8] dmaengine: xilinx_dma: Check for both idle > > and halted state in axidma stop_transfer > > > > On 05-09-19, 22:07, Radhey Shyam Pandey wrote: > > > From: Nicholas Graumann <nick.graumann@xxxxxxxxx> > > > > > > When polling for a stopped transfer in AXI DMA mode, in some cases the > > > status of the channel may indicate IDLE instead of HALTED if the > > > channel was reset due to an error. > > > > > > Signed-off-by: Nicholas Graumann <nick.graumann@xxxxxxxxx> > > > Signed-off-by: Radhey Shyam Pandey > > <radhey.shyam.pandey@xxxxxxxxxx> > > > --- > > > drivers/dma/xilinx/xilinx_dma.c | 5 +++-- > > > 1 file changed, 3 insertions(+), 2 deletions(-) > > > > > > diff --git a/drivers/dma/xilinx/xilinx_dma.c > > b/drivers/dma/xilinx/xilinx_dma.c > > > index b5dd62a..0896e07 100644 > > > --- a/drivers/dma/xilinx/xilinx_dma.c > > > +++ b/drivers/dma/xilinx/xilinx_dma.c > > > @@ -1092,8 +1092,9 @@ static int xilinx_dma_stop_transfer(struct > > xilinx_dma_chan *chan) > > > > > > /* Wait for the hardware to halt */ > > > return xilinx_dma_poll_timeout(chan, XILINX_DMA_REG_DMASR, > > val, > > > - val & XILINX_DMA_DMASR_HALTED, 0, > > > - XILINX_DMA_LOOP_COUNT); > > > + val | (XILINX_DMA_DMASR_IDLE | > > > + XILINX_DMA_DMASR_HALTED), > > > > The condition was bitwise AND and now is OR.. ?? > > Ah, it should be same as before . Only _IDLE mask should be in OR. > > Also on second thought to this patch- we need to describe which error > scenario "in some cases the status of the channel may indicate IDLE > instead of HALTED" as mentioned in commit description. > > @Nick: Can you comment? > In regard to the mask question, yes, this looks like a bug. We should be AND'ing with the mask like before. As far as the state, usually when we saw the IDLE state when invoking dmaengine_terminate_all on a channel that had errors. I have not proved this, but I believe what happened was the following: New transactions were queued when chan->err was set, causing xilinx_dma_chan_reset to be invoked which ultimately results in the hardware being in an IDLE state by the time xilinx_dma_terminate_all gets around to invoking stop_transfer. At that point, stop_transfer is going to time out waiting for the hardware to indicate it has HALTED and ultimately will time out. In any case, xilinx_dma_stop_transfer should be fine with the hardware being in an IDLE state to indicate that the active transfer is stopped. Case in point: The CDMA core also covered by this driver only has an IDLE bit and no HALTED bit in its DMASR, and it checks for just the IDLE bit in xilinx_cdma_stop_transfer(). > > > > > + 0, XILINX_DMA_LOOP_COUNT); > > > } > > > > > > /** > > > -- > > > 2.7.4 > > > > -- > > ~Vinod
