Sorry for delayed reply, I was consumed in some other work.
On 8/19/2019 11:10 PM, Jon Hunter wrote:
On 12/07/2019 12:10, Sameer Pujar wrote:
From Tegra186 onwards OUTSTANDING_REQUESTS field is added in channel
configuration register(bits 7:4) which defines the maximum number of reads
from the source and writes to the destination that may be outstanding at
any given point of time. This field must be programmed with a value
between 1 and 8. A value of 0 will prevent any transfers from happening.
Thus added 'ch_pending_req' member in chip data structure and the same is
populated with maximum allowed pending requests. Since the field is not
applicable to Tegra210, mentioned bit fields are unused and hence the
member is initialized with 0. For Tegra186, by default program this field
with the maximum permitted value of 8.
Fixes: 433de642a76c ("dmaengine: tegra210-adma: add support for Tegra186/Tegra194")
Signed-off-by: Sameer Pujar <spujar@xxxxxxxxxx>
---
drivers/dma/tegra210-adma.c | 7 +++++++
1 file changed, 7 insertions(+)
diff --git a/drivers/dma/tegra210-adma.c b/drivers/dma/tegra210-adma.c
index 2805853..5ab4e3a9 100644
--- a/drivers/dma/tegra210-adma.c
+++ b/drivers/dma/tegra210-adma.c
@@ -74,6 +74,8 @@
TEGRA186_ADMA_CH_FIFO_CTRL_TXSIZE(3) | \
TEGRA186_ADMA_CH_FIFO_CTRL_RXSIZE(3))
+#define TEGRA186_DMA_MAX_PENDING_REQS 8
+
#define ADMA_CH_REG_FIELD_VAL(val, mask, shift) (((val) & mask) << shift)
struct tegra_adma;
@@ -85,6 +87,7 @@ struct tegra_adma;
* @ch_req_tx_shift: Register offset for AHUB transmit channel select.
* @ch_req_rx_shift: Register offset for AHUB receive channel select.
* @ch_base_offset: Register offset of DMA channel registers.
+ * @ch_pending_req: Outstaning DMA requests for a channel.
s/Outstaning/Outstanding
will fix.
I do wonder if this variable should be a boolean variable
'has_oustanding_reqs' because this is not applicable to Tegra210. I
think this will be clearer that this is a difference between SoC
versions and that it should not be configured for Tegra210. And then ...
* @ch_fifo_ctrl: Default value for channel FIFO CTRL register.
* @ch_req_mask: Mask for Tx or Rx channel select.
* @ch_req_max: Maximum number of Tx or Rx channels available.
@@ -98,6 +101,7 @@ struct tegra_adma_chip_data {
unsigned int ch_req_tx_shift;
unsigned int ch_req_rx_shift;
unsigned int ch_base_offset;
+ unsigned int ch_pending_req;
unsigned int ch_fifo_ctrl;
unsigned int ch_req_mask;
unsigned int ch_req_max;
@@ -602,6 +606,7 @@ static int tegra_adma_set_xfer_params(struct tegra_adma_chan *tdc,
ADMA_CH_CTRL_FLOWCTRL_EN;
ch_regs->config |= cdata->adma_get_burst_config(burst_size);
ch_regs->config |= ADMA_CH_CONFIG_WEIGHT_FOR_WRR(1);
+ ch_regs->config |= cdata->ch_pending_req;
... you can ...
if (cdata->has_outstanding_reqs)
ch_regs->config |= TEGRA186_ADMA_CH_CONFIG_OUTSTNDREQS(8)
yes, this can be done. Will update in next revision.
ch_regs->fifo_ctrl = cdata->ch_fifo_ctrl;
ch_regs->tc = desc->period_len & ADMA_CH_TC_COUNT_MASK;
@@ -786,6 +791,7 @@ static const struct tegra_adma_chip_data tegra210_chip_data = {
.ch_req_tx_shift = 28,
.ch_req_rx_shift = 24,
.ch_base_offset = 0,
+ .ch_pending_req = 0,
.ch_fifo_ctrl = TEGRA210_FIFO_CTRL_DEFAULT,
.ch_req_mask = 0xf,
.ch_req_max = 10,
@@ -800,6 +806,7 @@ static const struct tegra_adma_chip_data tegra186_chip_data = {
.ch_req_tx_shift = 27,
.ch_req_rx_shift = 22,
.ch_base_offset = 0x10000,
+ .ch_pending_req = (TEGRA186_DMA_MAX_PENDING_REQS << 4),
.ch_fifo_ctrl = TEGRA186_FIFO_CTRL_DEFAULT,
.ch_req_mask = 0x1f,
.ch_req_max = 20,
