Re: [PATCH v2 2/2] dmaengine: sprd: Add Spreadtrum DMA configuration

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On 11-05-18, 19:44, Baolin Wang wrote:
> Hi Vinod,
> 
> On 11 May 2018 at 19:22, Vinod Koul <vkoul@xxxxxxxxxx> wrote:
> > On 09-05-18, 19:12, Baolin Wang wrote:
> >
> >> +/*
> >> + * struct sprd_dma_config - DMA configuration structure
> >> + * @cfg: dma slave channel runtime config
> >> + * @src_addr: the source physical address
> >> + * @dst_addr: the destination physical address
> >> + * @block_len: specify one block transfer length
> >> + * @transcation_len: specify one transcation transfer length
> >> + * @src_step: source transfer step
> >> + * @dst_step: destination transfer step
> >> + * @wrap_ptr: wrap pointer address, once the transfer address reaches the
> >> + * 'wrap_ptr', the next transfer address will jump to the 'wrap_to' address.
> >> + * @wrap_to: wrap jump to address
> >> + * @req_mode: specify the DMA request mode
> >> + * @int_mode: specify the DMA interrupt type
> >> + */
> >> +struct sprd_dma_config {
> >> +     struct dma_slave_config cfg;
> >> +     phys_addr_t src_addr;
> >> +     phys_addr_t dst_addr;
> >
> > these are already in cfg so why duplicate, same for few more here.
> 
> We save them in 'struct sprd_dma_config' as one parameter for
> sprd_dma_config(), otherwise we need add 2 more parameters (src and
> dst) for sprd_dma_config().

I am not sure I follow...

I meant you can use sprd_dma_config.cfg->src_addr/dst_addr and remove src_addr &
dst_addr in the sprd_dma_config. It duplicate..

Same for few more params...

> >> +     if (!is_slave_direction(dir) || sglen > 1)
> >> +             return NULL;
> >> +
> >> +     sdesc = kzalloc(sizeof(*sdesc), GFP_NOWAIT);
> >> +     if (!sdesc)
> >> +             return NULL;
> >> +
> >> +     for_each_sg(sgl, sg, sglen, i) {
> >> +             if (dir == DMA_MEM_TO_DEV) {
> >> +                     slave_cfg->src_addr = sg_dma_address(sg);
> >> +                     slave_cfg->dst_addr = slave_cfg->cfg.dst_addr;
> >> +                     slave_cfg->src_step =
> >> +                     sprd_dma_get_step(slave_cfg->cfg.src_addr_width);
> >> +                     slave_cfg->dst_step = SPRD_DMA_NONE_STEP;
> >> +             } else {
> >> +                     slave_cfg->src_addr = slave_cfg->cfg.src_addr;
> >> +                     slave_cfg->dst_addr = sg_dma_address(sg);
> >> +                     slave_cfg->src_step = SPRD_DMA_NONE_STEP;
> >> +                     slave_cfg->dst_step =
> >> +                     sprd_dma_get_step(slave_cfg->cfg.dst_addr_width);
> >
> > use a helper for filling this and passing right values for each case?
> 
> We need pass many values to this helper, but will try. Thanks.

I think 5 and that may help to look it better :)

-- 
~Vinod
--
To unsubscribe from this list: send the line "unsubscribe dmaengine" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html



[Index of Archives]     [Linux Kernel]     [Linux ARM (vger)]     [Linux ARM MSM]     [Linux Omap]     [Linux Arm]     [Linux Tegra]     [Fedora ARM]     [Linux for Samsung SOC]     [eCos]     [Linux PCI]     [Linux Fastboot]     [Gcc Help]     [Git]     [DCCP]     [IETF Announce]     [Security]     [Linux MIPS]     [Yosemite Campsites]

  Powered by Linux