[PATCH 26/44] dma-mapping: remove DMA_ERROR_CODE

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



And update the documentation - dma_mapping_error has been supported
everywhere for a long time.

Signed-off-by: Christoph Hellwig <hch@xxxxxx>
---
 Documentation/DMA-API-HOWTO.txt | 31 +++++--------------------------
 include/linux/dma-mapping.h     |  5 -----
 2 files changed, 5 insertions(+), 31 deletions(-)

diff --git a/Documentation/DMA-API-HOWTO.txt b/Documentation/DMA-API-HOWTO.txt
index 979228bc9035..4ed388356898 100644
--- a/Documentation/DMA-API-HOWTO.txt
+++ b/Documentation/DMA-API-HOWTO.txt
@@ -550,32 +550,11 @@ and to unmap it:
 	dma_unmap_single(dev, dma_handle, size, direction);
 
 You should call dma_mapping_error() as dma_map_single() could fail and return
-error. Not all DMA implementations support the dma_mapping_error() interface.
-However, it is a good practice to call dma_mapping_error() interface, which
-will invoke the generic mapping error check interface. Doing so will ensure
-that the mapping code will work correctly on all DMA implementations without
-any dependency on the specifics of the underlying implementation. Using the
-returned address without checking for errors could result in failures ranging
-from panics to silent data corruption. A couple of examples of incorrect ways
-to check for errors that make assumptions about the underlying DMA
-implementation are as follows and these are applicable to dma_map_page() as
-well.
-
-Incorrect example 1:
-	dma_addr_t dma_handle;
-
-	dma_handle = dma_map_single(dev, addr, size, direction);
-	if ((dma_handle & 0xffff != 0) || (dma_handle >= 0x1000000)) {
-		goto map_error;
-	}
-
-Incorrect example 2:
-	dma_addr_t dma_handle;
-
-	dma_handle = dma_map_single(dev, addr, size, direction);
-	if (dma_handle == DMA_ERROR_CODE) {
-		goto map_error;
-	}
+error.  Doing so will ensure that the mapping code will work correctly on all
+DMA implementations without any dependency on the specifics of the underlying
+implementation. Using the returned address without checking for errors could
+result in failures ranging from panics to silent data corruption.  The same
+applies to dma_map_page() as well.
 
 You should call dma_unmap_single() when the DMA activity is finished, e.g.,
 from the interrupt which told you that the DMA transfer is done.
diff --git a/include/linux/dma-mapping.h b/include/linux/dma-mapping.h
index 4f3eecedca2d..a57875309bfd 100644
--- a/include/linux/dma-mapping.h
+++ b/include/linux/dma-mapping.h
@@ -546,12 +546,7 @@ static inline int dma_mapping_error(struct device *dev, dma_addr_t dma_addr)
 
 	if (get_dma_ops(dev)->mapping_error)
 		return get_dma_ops(dev)->mapping_error(dev, dma_addr);
-
-#ifdef DMA_ERROR_CODE
-	return dma_addr == DMA_ERROR_CODE;
-#else
 	return 0;
-#endif
 }
 
 #ifndef HAVE_ARCH_DMA_SUPPORTED
-- 
2.11.0

--
To unsubscribe from this list: send the line "unsubscribe dmaengine" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html



[Index of Archives]     [Linux Kernel]     [Linux ARM (vger)]     [Linux ARM MSM]     [Linux Omap]     [Linux Arm]     [Linux Tegra]     [Fedora ARM]     [Linux for Samsung SOC]     [eCos]     [Linux PCI]     [Linux Fastboot]     [Gcc Help]     [Git]     [DCCP]     [IETF Announce]     [Security]     [Linux MIPS]     [Yosemite Campsites]

  Powered by Linux