On 01/17/2017 06:14 PM, Sergei Shtylyov wrote:
> On 01/17/2017 05:20 PM, Alexandre Bailon wrote:
>
>> DT binding for the TI DA8xx/OMAP-L1x/AM17xx/AM18xx cppi41 dma controller.
>
> "CPPI 4.1 DMA" again.
>
>>
>> Signed-off-by: Alexandre Bailon <abailon@xxxxxxxxxxxx>
>> ---
>> .../devicetree/bindings/usb/da8xx-usb.txt | 42
>> ++++++++++++++++++++++
>> 1 file changed, 42 insertions(+)
>>
>> diff --git a/Documentation/devicetree/bindings/usb/da8xx-usb.txt
>> b/Documentation/devicetree/bindings/usb/da8xx-usb.txt
>> index ccb844a..aed3169 100644
>> --- a/Documentation/devicetree/bindings/usb/da8xx-usb.txt
>> +++ b/Documentation/devicetree/bindings/usb/da8xx-usb.txt
>> @@ -18,10 +18,26 @@ Required properties:
>>
>> - phy-names: Should be "usb-phy"
>>
>> + - dmas: specifies the dma channels
>> +
>> + - dma-names: specifies the names of the channels. Use "rxN" for receive
>> + and "txN" for transmit endpoints. N specifies the endpoint number.
>> +
>> Optional properties:
>> ~~~~~~~~~~~~~~~~~~~~
>> - vbus-supply: Phandle to a regulator providing the USB bus power.
>>
>> +DMA
>> +~~~
>> +- compatible: ti,da8xx-cppi41
>> +- reg: offset and length of the following register spaces: CPPI DMA
>> Controller,
>> + CPPI DMA Scheduler, Queue Manager
>> +- reg-names: "controller", "scheduler", "queuemgr"
>> +- #dma-cells: should be set to 2. The first number represents the
>> + channel number (0 … 3 for endpoints 1 … 4).
>> + The second number is 0 for RX and 1 for TX transfers.
>> +- #dma-channels: should be set to 4 representing the 4 endpoints.
>
> Shouldn't the # of channels be a part of the glue data?
TBH I don't think know. For AM33xx, the number of channels is defined
so I did the same for DA850.
>
> [...]
>> @@ -39,5 +58,28 @@ Example:
>> phys = <&usb_phy 0>;
>> phy-names = "usb-phy";
>>
>> + dmas = <&cppi41dma 0 0 &cppi41dma 1 0
>> + &cppi41dma 2 0 &cppi41dma 3 0
>> + &cppi41dma 0 1 &cppi41dma 1 1
>> + &cppi41dma 2 1 &cppi41dma 3 1>;
>> + dma-names =
>> + "rx1", "rx2", "rx3", "rx4",
>> + "tx1", "tx2", "tx3", "tx4";
>> +
>> status = "okay";
>> +
>> + cppi41dma: dma-controller@201000 {
>> + compatible = "ti,da8xx-cppi41";
>> + reg = <0x201000 0x1000
>> + 0x202000 0x1000
>> + 0x204000 0x4000>;
>> + reg-names = "controller", "scheduler", "queuemgr";
>> + interrupts = <58>;
>> + interrupt-names = "glue";
>> + #dma-cells = <2>;
>> + #dma-channels = <4>;
>> + #dma-requests = <256>;
>
> Not seeing this prop documented...
Right. Actually, this prop is not even used so I will just remove it.
>
>> + status = "okay";
>
> Can be omitted.
>
>> + };
>> +
>> };
>>
>
Best Regards,
Alexandre
--
To unsubscribe from this list: send the line "unsubscribe dmaengine" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
