Hi Boris, >-----Original Message----- >From: Borislav Petkov [mailto:bp@xxxxxxxxx] >Sent: Monday, January 04, 2016 10:41 PM >To: Wang, Annie >Cc: Andy Shevchenko; Vinod Koul; Mika Westerberg; Greg Kroah-Hartman; Rafael >J. Wysocki; linux-acpi@xxxxxxxxxxxxxxx; linux-kernel@xxxxxxxxxxxxxxx; linux- >serial@xxxxxxxxxxxxxxx; dmaengine@xxxxxxxxxxxxxxx; Huang, Ray; Wan, Vincent; >Xue, Ken; Robin Murphy; Graeme Gregory; Li, Tony; Yu, Xiangliang >Subject: Re: [PATCH 1/6] 8250/Kconfig: add config option >CONFIG_SERIAL_8250_AMD > >On Mon, Jan 04, 2016 at 01:31:36PM +0800, Wang Hongcheng wrote: >> Add config option CONFIG_SERIAL_8250_AMD in use of AMD carrizo. >> Because carrizo's UART DMA device is an amba device, it selects >> ARM_AMBA option. Anything uses amba devices must select ARM_AMBA. >> >> Signed-off-by: Wang Hongcheng <annie.wang@xxxxxxx> >> --- >> drivers/tty/serial/8250/Kconfig | 8 ++++++++ >> 1 file changed, 8 insertions(+) >> >> diff --git a/drivers/tty/serial/8250/Kconfig >> b/drivers/tty/serial/8250/Kconfig index 6412f14..c9ebc31 100644 >> --- a/drivers/tty/serial/8250/Kconfig >> +++ b/drivers/tty/serial/8250/Kconfig >> @@ -378,3 +378,11 @@ config SERIAL_8250_MID >> Selecting this option will enable handling of the extra features >> present on the UART found on Intel Medfield SOC and various other >> Intel platforms. >> + >> +config SERIAL_8250_AMD >> + bool "AMD carrizo serial port support" >> + depends on SERIAL_8250 >> + select ARM_AMBA >> + help >> + If you have a Family 15h, models 0x60-0x6F based board and want to >> + use the serial port, say Y to this option. If unsure, say N. > >Hmm, so you're adding this config option here only to have >acpi_apd_setup_quirks() defined in an already AMD-specific compilation unit >drivers/acpi/acpi_apd.c. > How about I add select ARM_AMBA and SERIAL_8250 in arch/x86/Kconfig? diff --git a/arch/x86/Kconfig b/arch/x86/Kconfig index db3622f..0fe6657 100644 --- a/arch/x86/Kconfig +++ b/arch/x86/Kconfig @@ -537,11 +537,15 @@ config X86_AMD_PLATFORM_DEVICE depends on ACPI select COMMON_CLK select PINCTRL + select SERIAL_8250 + select ARM_AMBA ---help--- Select to interpret AMD specific ACPI device to platform device such as I2C, UART, GPIO found on AMD Carrizo and later chipsets. I2C and UART depend on COMMON_CLK to set clock. GPIO driver is - implemented under PINCTRL subsystem. + implemented under PINCTRL subsystem. Carrizo's UART is implemented + under SERIAL_8250. Carrizo's UART DMA device is an amba device, + it selects ARM_AMBA option. config IOSF_MBI tristate "Intel SoC IOSF Sideband support for SoC platforms" -- >So why not make drivers/acpi/acpi_apd.c depend on CPU_SUP_AMD and this way >it is automatically enabled on AMD and then check family/model/stepping when >assigning that > >+ .post_setup = acpi_apd_setup_quirks, > >thing? > >You need it only on F15h, models 0x60.. only so you don't really need the config >option when you can find out on what hardware you're running without the user >having to configure the kernel. > >Hmmm? CPU_SUP_AMD is only configured in X86 arch. AMD future ARM64 processors may also need acpi to platform support. ��.n��������+%������w��{.n��������)�)�� jg��� �����ݢj����G���� ���j:+v���w�m������w�������h�����٥
