On Wed, Jun 10, 2015 at 9:31 AM, Russell King - ARM Linux
<linux@xxxxxxxxxxxxxxxx> wrote:
> On Wed, Jun 10, 2015 at 09:00:31AM -0700, Dan Williams wrote:
>> On Wed, Jun 10, 2015 at 2:32 AM, Joerg Roedel <joro@xxxxxxxxxx> wrote:
>> > On Tue, Jun 09, 2015 at 12:27:10PM -0400, Dan Williams wrote:
>> >> diff --git a/arch/arm/mm/dma-mapping.c b/arch/arm/mm/dma-mapping.c
>> >> index 7e7583ddd607..9f6ff6671f01 100644
>> >> --- a/arch/arm/mm/dma-mapping.c
>> >> +++ b/arch/arm/mm/dma-mapping.c
>> >> @@ -1502,7 +1502,7 @@ static int __map_sg_chunk(struct device *dev, struct scatterlist *sg,
>> >> return -ENOMEM;
>> >>
>> >> for (count = 0, s = sg; count < (size >> PAGE_SHIFT); s = sg_next(s)) {
>> >> - phys_addr_t phys = page_to_phys(sg_page(s));
>> >> + phys_addr_t phys = sg_phys(s) - s->offset;
>> >
>> > So sg_phys() turns out to be 'page_to_phys(sg_page(s)) + s->offset',
>> > which makes the above statement to:
>> >
>> > page_to_phys(sg_page(s)) + s->offset - s->offset;
>> >
>> > The compiler will probably optimize that away, but it still doesn't look
>> > like an improvement.
>>
>> The goal is to eventually stop leaking struct page deep into the i/o
>> stack. Anything that relies on being able to retrieve a struct page
>> out of an sg entry needs to be converted. I think we need a new
>> helper for this case "sg_phys_aligned()?".
>
> Why? The aim of the code is not to detect whether the address is aligned
> to a page (if it were, it'd be testing for a zero s->offset, or it would
> be testing for an s->offset being a multiple of the page size.
>
> Let's first understand the code that's being modified (which seems to be
> something which isn't done very much today - people seem to just like
> changing code for the hell of it.)
>
> for (count = 0, s = sg; count < (size >> PAGE_SHIFT); s = sg_next(s)) {
> phys_addr_t phys = page_to_phys(sg_page(s));
> unsigned int len = PAGE_ALIGN(s->offset + s->length);
>
> if (!is_coherent &&
> !dma_get_attr(DMA_ATTR_SKIP_CPU_SYNC, attrs))
> __dma_page_cpu_to_dev(sg_page(s), s->offset, s->length,
> dir);
>
> prot = __dma_direction_to_prot(dir);
>
> ret = iommu_map(mapping->domain, iova, phys, len, prot);
> if (ret < 0)
> goto fail;
> count += len >> PAGE_SHIFT;
> iova += len;
> }
>
> What it's doing is trying to map each scatterlist entry via an IOMMU.
> Unsurprisingly, IOMMUs are page based - you can't map a partial IOMMU
> page.
>
> However, what says that the IOMMU page size is the same as the host CPU
> page size - it may not be... so the above code is wrong for a completely
> different reason.
>
> What we _should_ be doing is finding out what the IOMMU minimum page
> size is, and using that in conjunction with the sg_phys() of the
> scatterlist entry to determine the start and length of the mapping
> such that the IOMMU mapping covers the range described by the scatterlist
> entry. (iommu_map() takes arguments which must be aligned to the IOMMU
> minimum page size.)
>
> However, what we can also see from the above is that we have other code
> here using sg_page() - which is a necessity to be able to perform the
> required DMA cache maintanence to ensure that the data is visible to the
> DMA device. We need to kmap_atomic() these in order to flush them, and
> there's no other way other than struct page to represent a highmem page.
>
> So, I think your intent to want to remove struct page from the I/O
> subsystem is a false hope, unless you want to end up rewriting lots of
> architecture code, and you can come up with an alternative method to
> represent highmem pages.
I think there will always be cases that need to do pfn_to_page() for
buffer management. Those configurations will be blocked from seeing
cases where a pfn is not struct page backed. So, you can have highmem
or dma to pmem, but not both. Christoph, this is why I have Kconfig
symbols (DEV_PFN etc) to gate whether an arch/config supports pfn-only
i/o.
--
To unsubscribe from this list: send the line "unsubscribe dmaengine" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
