Did you fix multiple simultaneous DMA transfers in this? And easy test
is to start jack audio. Jack will start simultaneous cyclic transfers
on both the ALSA input and output. Since cyclic transfers never end,
multiple simultaneous transfers has to work. Last time I tried it I
got an immediate GPF when the second cyclic transfer was started.
On Tue, Feb 3, 2015 at 1:43 PM, Emilio López <emilio@xxxxxxxxxxxxx> wrote:
> Hi,
>
> El 01/02/15 a las 07:03, Priit Laes escibió:
>>
>> On Sat, 2015-01-31 at 19:58 -0300, Emilio López wrote:
>>>
>>> This patch adds support for the DMA engine present on Allwinner A10,
>>> A13, A10S and A20 SoCs. This engine has two kinds of channels:
>>> normal and dedicated. The main difference is in the mode of
>>> operation; while a single normal channel may be operating at any
>>> given time, dedicated channels may operate simultaneously provided
>>> there is no overlap of source or destination.
>>>
>>> Hardware documentation can be found on A10 User Manual (section 12),
>>> A13 User Manual (section 14) and A20 User Manual (section 1.12)
>>>
>>> Signed-off-by: Emilio López <emilio@xxxxxxxxxxxxx>
>
> (...)
>>>
>>> diff --git a/Documentation/devicetree/bindings/dma/sun4i-dma.txt
>>> b/Documentation/devicetree/bindings/dma/sun4i-dma.txt
>>> new file mode 100644
>>> index 0000000..f1634a2
>>> --- /dev/null
>>> +++ b/Documentation/devicetree/bindings/dma/sun4i-dma.txt
>>> @@ -0,0 +1,46 @@
>>> +Allwinner A10 DMA Controller
>>
>>
>> Don't you want to mention A13, A10S and A20 too?
>
>
> What if a new SoC shows up with this controller? :) I'd rather give a
> single name to the IP, like we do with the compatible strings.
>
> (...)
>
>>> diff --git a/drivers/dma/Makefile b/drivers/dma/Makefile
>>> index 2022b54..675b98f 100644
>>> --- a/drivers/dma/Makefile
>>> +++ b/drivers/dma/Makefile
>>> @@ -50,3 +50,4 @@ obj-y += xilinx/
>>> obj-$(CONFIG_INTEL_MIC_X100_DMA) += mic_x100_dma.o
>>> obj-$(CONFIG_NBPFAXI_DMA) += nbpfaxi.o
>>> obj-$(CONFIG_DMA_SUN6I) += sun6i-dma.o
>>> +obj-$(CONFIG_SUN4I_DMA) += sun4i-dma.o
>>> diff --git a/drivers/dma/sun4i-dma.c b/drivers/dma/sun4i-dma.c new file
>>> mode 100644
>>> index 0000000..a025405
>>> --- /dev/null
>>> +++ b/drivers/dma/sun4i-dma.c
>>> @@ -0,0 +1,1264 @@
>>> +/*
>>> + * Copyright (C) 2014 Emilio López
>>
>>
>> 2014, 2015 ?
>
>
> I guess so :)
>
> (...)
>>>
>>> +static int convert_burst(u32 maxburst)
>>> +{
>>> + if (maxburst > 8)
>>> + return -EINVAL;
>>
>> Would it make sense to add check for maxburst = 0 too?
>
>
> I can add one if you feel it's needed.
>
>>> +
>>> + /* 1 -> 0, 4 -> 1, 8 -> 2 */
>>> + return (maxburst >> 2);
>>> +}
>>> +
>>> +static int convert_buswidth(enum dma_slave_buswidth addr_width)
>>> +{
>>> + if (addr_width > DMA_SLAVE_BUSWIDTH_4_BYTES)
>>> + return -EINVAL;
>>> +
>>> + /* 8 (1 byte) -> 0, 16 (2 bytes) -> 1, 32 (4 bytes) -> 2 */
>>> + return (addr_width >> 1);
>>> +}
>>> +
>>> +static int choose_optimal_buswidth(dma_addr_t addr)
>>> +{
>>> + /* On 32 bit aligned addresses, we can use a 32 bit bus width */
>>> + if (addr % 4 == 0)
>>
>>
>> Not sure, whether it makes sense to optimize or not, but this can be
>> calculated like this:
>>
>> (addr & (4 - 1)) == 0
>
>
> It looks like IS_ALIGNED() in <linux/kernel.h> is what we need here.
>
>>> +static struct sun4i_dma_promise *
>>> +generate_ddma_promise(struct dma_chan *chan, dma_addr_t src, dma_addr_t
>>> dest,
>>> + size_t
>>> len, struct dma_slave_config *sconfig)
>>> +{
>>> + struct sun4i_dma_promise *promise;
>>> + int ret;
>>> +
>>> + promise = kzalloc(sizeof(*promise), GFP_NOWAIT);
>>> + if (!promise)
>>> + return NULL;
>>> +
>>> + promise->src = src;
>>> + promise->dst = dest;
>>> + promise->len = len;
>>> +
>>
>>
>> No timing parameters or this is just a quirk required for SPI?
>
>
> They're filled together with the endpoints, in case we need different
> ones for some other device. There's a big comment block explaining the
> situation on top of their assignment.
>
>>> promise->cfg = DDMA_CFG_LOADING |
>>> DDMA_CFG_BYTE_COUNT_MODE_REMAIN;
>>> +
>>> + /* Source burst */
>>> + ret = convert_burst(sconfig->src_maxburst);
>>> + if (IS_ERR_VALUE(ret))
>>> + goto fail;
>>> + promise->cfg |= DDMA_CFG_SRC_BURST_LENGTH(ret);
>>> +
>
>
> Thanks for reviewing this! :)
>
> Emilio
>
>
> --
> You received this message because you are subscribed to the Google Groups
> "linux-sunxi" group.
> To unsubscribe from this group and stop receiving emails from it, send an
> email to linux-sunxi+unsubscribe@xxxxxxxxxxxxxxxx.
> For more options, visit https://groups.google.com/d/optout.
--
Jon Smirl
jonsmirl@xxxxxxxxx
--
To unsubscribe from this list: send the line "unsubscribe dmaengine" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
