On Tue, Dec 23, 2014 at 9:22 PM, Vinod Koul <vinod.koul@xxxxxxxxx> wrote:
> On Thu, Dec 11, 2014 at 02:59:17PM -0800, Andrew Bresticker wrote:
>> Add support for the IMG Multi-threaded DMA Controller (MDC) found on
>> certain IMG SoCs. Currently this driver supports the variant present
>> on the MIPS-based Pistachio SoC.a
> Overall looks okay. I also need some review by DT folks on the bindings
Arnd has ack'ed the DT bindings, do you need someone else to review
them as well?
>> +static void mdc_list_desc_config(struct mdc_chan *mchan,
>> + struct mdc_hw_list_desc *ldesc,
>> + enum dma_transfer_direction dir,
>> + dma_addr_t src, dma_addr_t dst, size_t len)
>> +{
>> + struct mdc_dma *mdma = mchan->mdma;
>> + unsigned int max_burst, burst_size;
>> +
>> + ldesc->gen_conf = MDC_GENERAL_CONFIG_IEN | MDC_GENERAL_CONFIG_LIST_IEN |
>> + MDC_GENERAL_CONFIG_LEVEL_INT | MDC_GENERAL_CONFIG_PHYSICAL_W |
>> + MDC_GENERAL_CONFIG_PHYSICAL_R;
>> + ldesc->readport_conf =
>> + (mchan->thread << MDC_READ_PORT_CONFIG_STHREAD_SHIFT) |
>> + (mchan->thread << MDC_READ_PORT_CONFIG_RTHREAD_SHIFT) |
>> + (mchan->thread << MDC_READ_PORT_CONFIG_WTHREAD_SHIFT);
>> + ldesc->read_addr = src;
>> + ldesc->write_addr = dst;
>> + ldesc->xfer_size = len - 1;
>> + ldesc->node_addr = 0;
>> + ldesc->cmds_done = 0;
>> + ldesc->ctrl_status = MDC_CONTROL_AND_STATUS_LIST_EN |
>> + MDC_CONTROL_AND_STATUS_EN;
>> + ldesc->next_desc = NULL;
>> +
>> + if (IS_ALIGNED(dst, mdma->bus_width) &&
>> + IS_ALIGNED(src, mdma->bus_width))
>> + max_burst = mdma->bus_width * mdma->max_burst_mult;
>> + else
>> + max_burst = mdma->bus_width * (mdma->max_burst_mult - 1);
>> +
>> + if (dir == DMA_MEM_TO_DEV) {
>> + ldesc->gen_conf |= MDC_GENERAL_CONFIG_INC_R;
>> + ldesc->readport_conf |= MDC_READ_PORT_CONFIG_DREQ_ENABLE;
>> + mdc_set_read_width(ldesc, mdma->bus_width);
>> + mdc_set_write_width(ldesc, mchan->config.dst_addr_width);
>> + burst_size = min(max_burst, mchan->config.dst_maxburst *
>> + mchan->config.dst_addr_width);
> why is this calculation done for burst size? Shouldn't we take the
> config.dst_maxburst value configured by client?
It's possible that the client could select a burst size that is too
large (i.e. it exceeds the max_burst calculated above), so we cap it
here to max_burst.
>> +static struct dma_async_tx_descriptor *mdc_prep_slave_sg(
>> + struct dma_chan *chan, struct scatterlist *sgl,
>> + unsigned int sg_len, enum dma_transfer_direction dir,
>> + unsigned long flags, void *context)
>> +{
>> + struct mdc_chan *mchan = to_mdc_chan(chan);
>> + struct mdc_dma *mdma = mchan->mdma;
>> + struct mdc_tx_desc *mdesc;
>> + struct scatterlist *sg;
>> + struct mdc_hw_list_desc *curr, *prev = NULL;
>> + dma_addr_t curr_phys, prev_phys;
>> + unsigned int i;
>> +
>> + if (!sgl)
>> + return NULL;
>> +
>> + if (!is_slave_direction(dir))
>> + return NULL;
>> +
>> + if (mdc_check_slave_width(mchan, dir) < 0)
>> + return NULL;
>> +
>> + mdesc = kzalloc(sizeof(*mdesc), GFP_NOWAIT);
>> + if (!mdesc)
>> + return NULL;
>> + mdesc->chan = mchan;
>> +
>> + for_each_sg(sgl, sg, sg_len, i) {
>> + dma_addr_t buf = sg_dma_address(sg);
>> + size_t buf_len = sg_dma_len(sg);
>> +
>> + while (buf_len > 0) {
>> + size_t xfer_size;
>> +
>> + curr = dma_pool_alloc(mdma->desc_pool, GFP_NOWAIT,
>> + &curr_phys);
>> + if (!curr)
>> + goto free_desc;
>> +
>> + if (!prev) {
>> + mdesc->list_phys = curr_phys;
>> + mdesc->list = curr;
>> + } else {
>> + prev->node_addr = curr_phys;
>> + prev->next_desc = curr;
>> + }
>> +
>> + xfer_size = min_t(size_t, mdma->max_xfer_size,
>> + buf_len);
>> +
>> + if (dir == DMA_MEM_TO_DEV) {
>> + mdc_list_desc_config(mchan, curr, dir, buf,
>> + mchan->config.dst_addr,
>> + xfer_size);
>> + } else {
>> + mdc_list_desc_config(mchan, curr, dir,
>> + mchan->config.src_addr,
>> + buf, xfer_size);
>> + }
>> +
>> + prev = curr;
>> + prev_phys = curr_phys;
>> +
>> + mdesc->list_len++;
>> + mdesc->list_xfer_size += xfer_size;
>> + buf += xfer_size;
>> + buf_len -= xfer_size;
> i see this pattern is repeat in all the .prepare calls, can we make it bit
> generic and use that in the these three calls..
I've pulled out almost all of the common stuff into
mdc_list_desc_config(). I suppose the list manipulation could be
moved there as well, but the rest is all slightly different in each
case.
>> + dma_cap_zero(mdma->dma_dev.cap_mask);
>> + dma_cap_set(DMA_SLAVE, mdma->dma_dev.cap_mask);
>> + dma_cap_set(DMA_PRIVATE, mdma->dma_dev.cap_mask);
>> + dma_cap_set(DMA_CYCLIC, mdma->dma_dev.cap_mask);
> and you dont seen to support pause/resume, though not a blocker but is it
> not supported in HW or driver doesn't?
Someone from IMG can correct me if I'm wrong, but I don't think the HW
supports it.
--
To unsubscribe from this list: send the line "unsubscribe dmaengine" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
