On wto, 2014-09-23 at 17:39 +0200, Ulf Hansson wrote:
> On 18 September 2014 12:09, Krzysztof Kozlowski <k.kozlowski@xxxxxxxxxxx> wrote:
> > On śro, 2014-09-17 at 20:42 +0200, Ulf Hansson wrote:
> >> On 16 September 2014 10:51, Krzysztof Kozlowski <k.kozlowski@xxxxxxxxxxx> wrote:
> >
> > [...]
> >
> >> >
> >> > @@ -2585,6 +2620,34 @@ static int pl330_dma_device_slave_caps(struct dma_chan *dchan,
> >> > return 0;
> >> > }
> >> >
> >> > +/*
> >> > + * Assume that IRQ safe runtime PM is chosen in probe and amba bus driver
> >> > + * will only disable/enable the clock in runtime PM suspend/resume.
> >> > + */
> >> > +static int __maybe_unused pl330_suspend(struct device *dev)
> >> > +{
> >> > + struct amba_device *pcdev = to_amba_device(dev);
> >> > +
> >> > + if (!pm_runtime_suspended(dev))
> >> > + amba_pclk_disable(pcdev);
> >>
> >> I would suggest to use pm_runtime_force_suspend() instead of the above.
> >
> > Sure, I can change it but... (see below)
> >
> >>
> >> > + amba_pclk_unprepare(pcdev);
> >> > +
> >> > + return 0;
> >> > +}
> >> > +
> >> > +static int __maybe_unused pl330_resume(struct device *dev)
> >> > +{
> >> > + struct amba_device *pcdev = to_amba_device(dev);
> >> > +
> >> > + amba_pclk_prepare(pcdev);
> >> > + if (!pm_runtime_suspended(dev))
> >> > + return amba_pclk_enable(pcdev);
> >>
> >> The above if statement could be replaced with pm_runtime_force_resume().
> >
> > But that would lead to runtime resuming the device even when it is not
> > needed. We don't have to fully wakeup the device during resume operation
> > when the device was runtime suspended before suspend.
>
> That's true - but that's not a big issue I believe. I think the below
> problems are worse. :-)
>
> 1) You don't disable runtime PM, thus not preventing the runtime PM
> callbacks from being invoked.
> 2) You don't update the runtime PM status, thus not reflecting the
> actual state of the device.
>
> Both the above may cause unbalanced clk_enable|disable calls.
>
> Don't get me wrong, I certainly think the "don't do runtime PM resume
> during system PM resume" is interesting to solve. But that it's a
> common problem and should be supported by the runtime PM API somehow
> instead. I have been thinking of extending the
> pm_runtime_force_resume() API to support this, let's see when that
> happens. :-)
OK, I get the point. I'll fix this.
> >
> >>
> >> Doing that, means the amba_pclk_enable|disable() don't need to be
> >> exported from the AMBA bus header, but entirely handled by the AMBA
> >> bus itself.
> >>
> >> > +
> >> > + return 0;
> >> > +}
> >> > +
> >> > +static SIMPLE_DEV_PM_OPS(pl330_pm, pl330_suspend, pl330_resume);
> >> > +
> >> > static int
> >> > pl330_probe(struct amba_device *adev, const struct amba_id *id)
> >> > {
> >> > @@ -2738,6 +2801,9 @@ pl330_probe(struct amba_device *adev, const struct amba_id *id)
> >> > pcfg->data_buf_dep, pcfg->data_bus_width / 8, pcfg->num_chan,
> >> > pcfg->num_peri, pcfg->num_events);
> >> >
> >>
> >> You need pm_runtime_set_active() here as well.
> >
> > This is done by amba/bus.c. Do I have to do it again?
>
> Ohh, you are right! No need to add it!
>
> >
> >>
> >> > + pm_runtime_irq_safe(&adev->dev);
> >> > + pm_runtime_put_noidle(&adev->dev);
> >>
> >> Why pm_runtime_put_noidle(), that seems like you might end up leaving
> >> the device in active state - unless you get some request. Likely not
> >> what you want?
> >
> > Hmmm... I am sorry but I do not get the point here. It could be
> > pm_runtime_put() as well because initially we start with counter
> > incremented by amba/bus.c.
>
> The "no_idle" version will prevent the device from going inactive,
> unless a new cycle of pm_runtime_get() to pm_runtime_put() happens,
> which there are no guarantees of.
Right.
Thanks for reviewing the code. I'll send the next version removing also
the amba_pclk_enable|disable() macros.
Best regards,
Krzysztof
>
> Kind regards
> Uffe
--
To unsubscribe from this list: send the line "unsubscribe dmaengine" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
