Re: [PATCH] dmaengine: qcom_bam_dma: Add descriptor flag APIs

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 





On 22/05/14 16:09, Andy Gross wrote:
On Thu, May 22, 2014 at 11:40:49AM +0530, Vinod Koul wrote:

<snip>

I have 3 different IRQs that can be asserted based on the bit I set in the
hardware descriptor.  The normal IRQ is the INT bit.  However, in some cases the
peripheral protocol requires the use of the EOT or EOB interrupt instead.  The
DMA_PREP_INTERRUPT would only work if I had only 2 choices.

Thinking about this more, I could use the DMA_PREP_INTERRUPT to cover the EOT
flag.  However, I might get in a bind later if I need to support the EOB (end of
block) interrupt.
Sorry for delay in this.

I think it would make sense to use DMA_PREP_INTERRUPT for EOB interrupt. The EOT
should always be enabled for the cases where it is applicable instead of nomral
irq.

That should genrically ocvery your cases, or did we miss anything here

The EOT is not used for every transaction.  It is part of a handshaking
protocol with the attached peripheral, much like the NWD (notify when done).  As
near as I can tell today, no peripheral depends on the EOB, so we could drop it
for now until it is needed and cross this bridge when we need to.

As EOT behaviour is totally dependent on the attached peripheral(or channel), Can't we make this specific to channel by passing additional flags in the DT dma channel descriptors? This will be better abstraction for drivers as well.

I know that EOT flag is part of descriptor but still some channels *must* have EOT to run there state-machine correctly. So making it optional for those channels might be wrong.

Are there any use cases for particular *channel* where EOT requirement changes dynamically?



--srini






The NWD flag requests that the peripheral wait until the data has been fully
processed before signaling an interrupt.
interrupt for transaction complete or DMA request?

This is a special signaling mechanism that holds off the DMA interrupt until the
peripheral actually acks that the data has been processed completely.  This is
required in many cases by the peripheral.  One example is the SPI controller.
At the end of a transaction you are supposed to set the NWD so that the chip
select is de-asserted.

I'm not sure what flag I could map this to... maybe DMA_CTRL_ACK?  or maybe the
DMA_PREP_FENCE?  I don't generally like overloading the flags and slightly
twisting their intent.  Could we add a flag to denote device ACK?
Nope lets not override these...

Then I need to add a flag.  Something like DMA_PREP_DEVICE_ACK that denotes that the
attached device needs to ACK the transfer.

Also, one thing I forgot.  For crypto and some of the other blocks, we have
something called command descriptors that can be transferred to the blocks to
provide programming or direction.  The DMA controller has a flag that tells the
attached peripheral that the incoming DMA contains command descriptors.  The dma
descriptors still point to a memory region to transfer, but the contents are
interpreted differently.  This is yet another flag in the descriptor flag
section.  I'd need another flag for this as well.  Something like DMA_PREP_CMD.

We are actively working on upstreaming our crypto block and this will be
required for that to work properly.

--
To unsubscribe from this list: send the line "unsubscribe dmaengine" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html




[Index of Archives]     [Linux Kernel]     [Linux ARM (vger)]     [Linux ARM MSM]     [Linux Omap]     [Linux Arm]     [Linux Tegra]     [Fedora ARM]     [Linux for Samsung SOC]     [eCos]     [Linux PCI]     [Linux Fastboot]     [Gcc Help]     [Git]     [DCCP]     [IETF Announce]     [Security]     [Linux MIPS]     [Yosemite Campsites]

  Powered by Linux