[+Cc dm-devel and linux-fscrypt] On Fri, Jun 14, 2019 at 10:34:01AM +0200, Ard Biesheuvel wrote: > This series is presented as an RFC for a couple of reasons: > - it is only build tested > - it is unclear whether this is the right way to move away from the use of > bare ciphers in non-crypto code > - we haven't really discussed whether moving away from the use of bare ciphers > in non-crypto code is a goal we agree on > > This series creates an ESSIV shash template that takes a (cipher,hash) tuple, > where the digest size of the hash must be a valid key length for the cipher. > The setkey() operation takes the hash of the input key, and sets into the > cipher as the encryption key. Digest operations accept input up to the > block size of the cipher, and perform a single block encryption operation to > produce the ESSIV output. > > This matches what both users of ESSIV in the kernel do, and so it is proposed > as a replacement for those, in patches #2 and #3. > > As for the discussion: the code is untested, so it is presented for discussion > only. I'd like to understand whether we agree that phasing out the bare cipher > interface from non-crypto code is a good idea, and whether this approach is > suitable for fscrypt and dm-crypt. > > Remaining work: > - wiring up some essiv(x,y) combinations into the testing framework. I wonder > if anything other than essiv(aes,sha256) makes sense. > - testing - suggestions welcome on existing testing frameworks for dm-crypt > and/or fscrypt > > Cc: Herbert Xu <herbert@xxxxxxxxxxxxxxxxxxx> > Cc: Eric Biggers <ebiggers@xxxxxxxxxx> > > Ard Biesheuvel (3): > crypto: essiv - create a new shash template for IV generation > dm crypt: switch to essiv shash > fscrypt: switch to ESSIV shash > > crypto/Kconfig | 3 + > crypto/Makefile | 1 + > crypto/essiv.c | 275 ++++++++++++++++++++ > drivers/md/Kconfig | 1 + > drivers/md/dm-crypt.c | 137 ++-------- > fs/crypto/Kconfig | 1 + > fs/crypto/crypto.c | 11 +- > fs/crypto/fscrypt_private.h | 4 +- > fs/crypto/keyinfo.c | 64 +---- > 9 files changed, 321 insertions(+), 176 deletions(-) > create mode 100644 crypto/essiv.c I agree that moving away from bare block ciphers is generally a good idea. For fscrypt I'm fine with moving ESSIV into the crypto API, though I'm not sure a shash template is the best approach. Did you also consider making it a skcipher template so that users can do e.g. "essiv(cbc(aes),sha256,aes)"? That would simplify things much more on the fscrypt side, since then all the ESSIV-related code would go away entirely except for changing the string "cbc(aes)" to "essiv(cbc(aes),sha256,aes)". Either way, for testing the fscrypt change, I recently added tests to xfstests that verify the on-disk ciphertext in userspace, including for non-default modes such as the AES-128-CBC-ESSIV in question. So I'm not too worried about the fscrypt encryption getting accidentally broken anymore. If you want to run the AES-128-CBC-ESSIV test yourself, you should be able to do it by following the directions at https://github.com/tytso/xfstests-bld/blob/master/Documentation/kvm-quickstart.md and running 'kvm-xfstests -c ext4 generic/549'. As for adding essiv to testmgr, sha256 and aes would be enough for fscrypt. There aren't any plans to add more ESSIV settings to fscrypt, and AES-128-CBC-ESSIV was only added in the first place because some people wanted to use fscrypt on platforms with CBC hardware acceleration but not XTS. - Eric -- dm-devel mailing list dm-devel@xxxxxxxxxx https://www.redhat.com/mailman/listinfo/dm-devel
