Remove the FIXME markers by filling in missing content, and make some other minor fixes. Signed-off-by: Martin Wilck <mwilck@xxxxxxxx> Acked-by: Benjamin Marzinski <bmarzins@xxxxxxxxxx> Reviewed-by: Hannes Reinecke <hare@xxxxxxxx> --- multipath/multipath.conf.5 | 48 +++++++++++++++++++++++++--------------------- 1 file changed, 26 insertions(+), 22 deletions(-) diff --git a/multipath/multipath.conf.5 b/multipath/multipath.conf.5 index d5d9438a..000a42ec 100644 --- a/multipath/multipath.conf.5 +++ b/multipath/multipath.conf.5 @@ -258,7 +258,7 @@ Return a constant priority of \fI1\fR. .I sysfs Use the sysfs attributes \fIaccess_state\fR and \fIpreferred_path\fR to generate the path priority. This prioritizer accepts the optional prio_arg -\fIexclusive_pref_bit\fR +\fIexclusive_pref_bit\fR. .TP .I emc (Hardware-dependent) @@ -300,14 +300,19 @@ Generate the path priority based on a latency algorithm. Requires prio_args keyword. .TP .I datacore -.\" XXX -???. Requires prio_args keyword. +(Hardware-dependent) +Generate the path priority for some Datacore storage arrays. Requires prio_args +keyword. .TP .I iet -.\" XXX -???. Requires prio_args keyword. -.TP -The default is: \fBconst\fR +(iSCSI only) +Generate path priority for iSCSI targets based on IP address. Requires +prio_args keyword. +.PP +The default depends on the \fBdetect_prio\fR setting: If \fBdetect_prio\fR is +\fByes\fR (default), the default priority algorithm is \fBsysfs\fR (except for +NetAPP E-Series, where it is \fBalua\fR). If \fBdetect_prio\fR is +\fBno\fR, the default priority algorithm is \fBconst\fR. .RE . . @@ -364,12 +369,12 @@ If \fIexclusive_pref_bit\fR is set, paths with the \fIpreferred path\fR bit set will always be in their own path group. .TP .I datacore -.\" XXX -\fIpreferredsds\fR ???. +\fIpreferredsds\fR (required) denotes the preferred "SDS name" for datacore +arrays. \fItimeout\fR (optional) is the timeout for the INQUIRY, in ms. .TP .I iet -.\" XXX -\fIpreferredip\fR ???. +\fIpreferredip=...\fR (required) denotes the preferred IP address (in dotted decimal +notation) for iSCSI targets. .TP The default is: \fB<unset>\fR .RE @@ -384,29 +389,28 @@ Possible values for the feature list are: .TP 12 .\" XXX .I queue_if_no_path -(Superseded by \fIno_path_retry\fR) (Since ??? kernel) Queue I/O if no path is active. +(Superseded by \fIno_path_retry\fR) Queue I/O if no path is active. Identical to the \fIno_path_retry\fR with \fIqueue\fR value. If both this feature and \fIno_path_retry\fR are set, the latter value takes precedence. See KNOWN ISSUES. .TP -.I no_partitions -Disable automatic partitions generation via kpartx. -.TP .\" XXX .I pg_init_retries <times> -(Since ??? kernel) Number of times to retry pg_init, it must be between 1 and 50. +(Since kernel 2.6.24) Number of times to retry pg_init, it must be between 1 and 50. .TP .\" XXX .I pg_init_delay_msecs <msecs> -(Since ??? kernel) Number of msecs before pg_init retry, it must be between 0 and 60000. +(Since kernel 2.6.38) Number of msecs before pg_init retry, it must be between 0 and 60000. .TP .\" XXX .I queue_mode <mode> -(Since ??? kernel) Select the the queue_mode per multipath device. -Where <mode> can be \fIbio\fR, \fIrq\fR or \fImq\fR. Which corresponds to -bio-based, request_fn rq-based, and blk-mq rq-based respectively. -.TP -The default is: \fB0\fR +(Since kernel 4.8) Select the the queueing mode per multipath device. +<mode> can be \fIbio\fR, \fIrq\fR or \fImq\f, which corresponds to +bio-based, request-based, and block-multiqueue (blk-mq) request-based, +respectively. + +The default depends on the kernel parameter \fBdm_mod.use_blk_mq\fR. It is +\fImq\fR if the latter is set, and \fIrq\fR otherwise. .RE . . -- 2.13.1 -- dm-devel mailing list dm-devel@xxxxxxxxxx https://www.redhat.com/mailman/listinfo/dm-devel
