On Sat, Oct 22, 2011 at 06:02:47PM +0300, Pasi Kärkkäinen wrote: > On Wed, Oct 05, 2011 at 03:54:35PM -0400, Adam Chasen wrote: > > John, > > I am limited in a similar fashion. I would much prefer to use multibus > > multipath, but was unable to achieve bandwidth which would exceed a > > single link even though it was spread over the 4 available links. Were > > you able to gain even a similar performance of the RAID0 setup with > > the multibus multipath? > > > > Utilizing multiple links works with for example this setup: > - VMware ESXi 4.1 software iSCSI initiator. > - Dell Equallogic iSCSI target. > > The steps needed for ESXi are: > - Configure multiple VMkernel (vmkX) IP interfaces. And I forgot to write this: - Bind the vmkX interfaces to portgroups that use dedicated NICs. > - Configure ESXi iscsi initiator to use (bind to) all the vmkX interfaces. > - Configure the path selection policy to be RR (RoundRobin). > - Configure multipath to switch paths after 3 IOs. > > > The same should work with Linux dm-multipath. > > That should be it. -- Pasi > > > Thanks, > > Adam > > > > On Tue, Oct 4, 2011 at 11:07 PM, John A. Sullivan III > > <jsullivan@xxxxxxxxxxxxxxxxxxx> wrote: > > > On Tue, 2011-10-04 at 16:19 -0400, Adam Chasen wrote: > > >> Unfortunately even with playing around with various settings, queues, > > >> and other techniques, I was never able to exceed the bandwidth of more > > >> than one of the Ethernet links when accessing a single multipathed > > >> LUN. > > >> > > >> When communicating with two different multipathed LUNs, which present > > >> as two different multipath devices, I can saturate two links, but it > > >> is still a one to one ratio of multipath devices to link saturation. > > >> > > >> After further research on multipathing, it appears people are using md > > >> raid to achieve multipathed devices. My initial testing of using raid0 > > >> md-raid device produces the behavior I expect of multipathed devices. > > >> I can easily saturate both links during read operations. > > >> > > >> I feel using md-raid is a less elegant solution than using > > >> dm-multipath, but it will have to suffice until someone can provide me > > >> some additional guidance. > > >> > > >> Thanks, > > >> Adam > > > We recently changed from the RAID0 approach to multipath multibus. > > > RAID0 did seem to give more even performance over a variety of IO > > > patterns but it had a critical flaw. We could not use the snapshot > > > capabilities of the SAN because we could never be certain of > > > snapshotting the RAID0 disks in a transactionally consistent state. If > > > I have four disk in a RAID0 array and snapshot them all, how can I be > > > assured that I have not done something like written two of three stripes > > > and no parity. This was our singular reason for discarding RAID0 over > > > iSCSI for multipath multibus - John > > > > > >> > > >> On Mon, Oct 3, 2011 at 11:08 PM, Adam Chasen <adam@xxxxxxxxxxx> wrote: > > >> > Malahal, > > >> > After your mentioning bio vs request based I attempted to determine if > > >> > my kernel contains the request based mpath. It seems in 2.6.31 all > > >> > mpath was switched to request based. I have a kernel 2.6.31+ (actually > > >> > .35 and .38), so I believe I have requrest-based mpath. > > >> > > > >> > All, > > >> > There also appears to be a new multipath configuration option > > >> > documented in the RHEL 6 beta documentation: > > >> > rr_min_io_rq Specifies the number of I/O requests to route to a path > > >> > before switching to the next path in the current path group, using > > >> > request-based device-mapper-multipath. This setting should be used on > > >> > systems running current kernels. On systems running kernels older than > > >> > 2.6.31, use rr_min_io. The default value is 1. > > >> > > > >> > http://docs.redhat.com/docs/en-US/Red_Hat_Enterprise_Linux/6-Beta/html/DM_Multipath/config_file_multipath.html > > >> > > > >> > I have not tested using this setting vs rr_min_io yet or even if my > > >> > system supports the configuration directive. > > >> > > > >> > If I trust some of the claims of several VMware ESX iscsi multipath > > >> > setups, it is possible (possibly using different software) to gain a > > >> > multiplicative throughput by adding additional Ethernet links. This > > >> > makes me hopeful that we can do this with open-iscsi and dm-mulitpath > > >> > as well. > > >> > > > >> > It could be something obvious I am missing, but it appears a lot of > > >> > people experience this same issue. > > >> > > > >> > Thanks, > > >> > Adam > > >> > > > >> > On Tue, May 3, 2011 at 6:12 AM, John A. Sullivan III > > >> > <jsullivan@xxxxxxxxxxxxxxxxxxx> wrote: > > >> >> On Mon, 2011-05-02 at 22:04 -0700, Malahal Naineni wrote: > > >> >>> John A. Sullivan III [jsullivan@xxxxxxxxxxxxxxxxxxx] wrote: > > >> >>> > I'm also very curious about your findings on rr_min_io. I cannot find > > >> >>> > my benchmarks but we tested various settings heavily. I do not recall > > >> >>> > if we saw more even scaling with 10 or 100. I remember being surprised > > >> >>> > that performance with it set to 1 was poor. I would have thought that, > > >> >>> > in a bonded environment, changing paths per iSCSI command would give > > >> >>> > optimal performance. Can anyone explain why it does not? > > >> >>> > > >> >>> rr_min_io of 1 will give poor performance if your multipath kernel > > >> >>> module doesn't support request based multipath. In those BIO based > > >> >>> multipath, multipath receives 4KB requests. Such requests can't be > > >> >>> coalesced if they are sent on different paths. > > >> >> <snip> > > >> >> Ah, that makes perfect sense and why 3 seems to be the magic number in > > >> >> Linux (4000 / 1460 (or whatever IP payload is)). Does that change with > > >> >> Jumbo frames? In fact, how would that be optimized in Linux? > > >> >> > > >> >> 9KB seems to be a reasonable common jumbo frame value for various > > >> >> vendors and that should contain two pages but, I would guess, Linux > > >> >> can't utilize it as each block must be independently acknowledged. Is > > >> >> that correct? Thus a frame size of a little over 4KB would be optimal > > >> >> for Linux? > > >> >> > > >> >> Would that mean that rr_min_io of 1 would become optimal? However, if > > >> >> each block needs to be acknowledged before the next is sent, I would > > >> >> think we are still latency bound, i.e., even if I can send four requests > > >> >> down four separate paths, I cannot send the second until the first has > > >> >> been acknowledged and since I can easily place four packets on the same > > >> >> path within the latency period of four packets, multibus gives me > > >> >> absolutely no performance advantage for a single iSCSI stream and only > > >> >> proves useful as I start multiplexing multiple iSCSI streams. > > >> >> > > >> >> Is that analysis correct? If so, what constitutes a separate iSCSI > > >> >> stream? Are two separate file requests from the same file systems to the > > >> >> same iSCSI device considered two iSCSI streams and thus can be > > >> >> multiplexed and benefit from multipath or are they considered all part > > >> >> of the same iSCSI stream? If they are considered one, do they become two > > >> >> if they reside on different partitions and thus different file systems? > > >> >> If not, then do we only see multibus performance gains between a single > > >> >> file system host and a single iSCSI host when we use virtualization each > > >> >> with their own iSCSI connection (as opposed to using iSCSI connections > > >> >> in the underlying host and exposing them to the virtual machines as > > >> >> local storage)? > > >> >> > > >> >> I hope I'm not hijacking this thread and realize I've asked some > > >> >> convoluted questions but optimizing multibus through bonded links for > > >> >> single large hosts is still a bit of a mystery to me. Thanks - John > > >> >> > > >> >> -- > > >> >> dm-devel mailing list > > >> >> dm-devel@xxxxxxxxxx > > >> >> https://www.redhat.com/mailman/listinfo/dm-devel > > >> >> > > >> > > > >> > > >> -- > > >> dm-devel mailing list > > >> dm-devel@xxxxxxxxxx > > >> https://www.redhat.com/mailman/listinfo/dm-devel > > > > > > > > > -- > > > dm-devel mailing list > > > dm-devel@xxxxxxxxxx > > > https://www.redhat.com/mailman/listinfo/dm-devel > > > > > > > -- > > dm-devel mailing list > > dm-devel@xxxxxxxxxx > > https://www.redhat.com/mailman/listinfo/dm-devel > > -- > dm-devel mailing list > dm-devel@xxxxxxxxxx > https://www.redhat.com/mailman/listinfo/dm-devel -- dm-devel mailing list dm-devel@xxxxxxxxxx https://www.redhat.com/mailman/listinfo/dm-devel
