On Tue, 19 Oct 2010 14:55:31 -0400 (EDT) Mikulas Patocka <mpatocka@xxxxxxxxxx> wrote: > > > On Sun, 12 Sep 2010, Neil Brown wrote: > > > On Wed, 8 Sep 2010 09:32:13 -0400 (EDT) > > Mikulas Patocka <mpatocka@xxxxxxxxxx> wrote: > > > > > Hi > > > > > > when reviewing some i_size problem, I searched the kernel for i_size usage > > > (the variable should really be written with i_size_write and read with > > > i_size_read). > > > > > > Properly locked direct use of "i_size" inside memory management or > > > filesystems may not be a problem, but there are many problems in general > > > code outside mm. > > > > > > The misuses are: > > > SOUND/SOUND_FIRMWARE.C:l = filp->f_path.dentry->d_inode->i_size; > > > KERNEL/RELAY.C:buf->dentry->d_inode->i_size = buf->early_bytes; > > > KERNEL/RELAY.C:buf->dentry->d_inode->i_size += buf->chan->subbuf_size > > > -buf->padding[old_subbuf]; > > > DRIVERS/USB/CORE/INODE.C:dev->usbfs_dentry->d_inode->i_size = i_size; > > > DRIVERS/MTD/DEVICES/BLOCK2MTD.C:dev->mtd.size = > > > dev->blkdev->bd_inode->i_size & PAGE_MASK; > > > DRIVERS/MD/MD.C: many reads of i_size > > > DRIVERS/BLOCK/NBD.C: many writes to i_size without i_size_write > > > DRIVERS/BLOCK/DRBD/DRBD_INT.H: return bdev ? bdev->bd_inode->i_size >> 9 : 0; > > > DRIVERS/BLOCK/DRBD/DRBD_WRAPPERS.H: mdev->this_bdev->bd_inode->i_size = > > > (loff_t)size << 9; > > > BLOCK/BLK-CORE.C:printk(KERN_INFO "%s: rw=%ld, want=%Lu, limit=%Lu\n", > > > bdevname(bio->bi_bdev, b), > > > bio->bi_rw, > > > (unsigned long long)bio->bi_sector + bio_sectors(bio), > > > (long long)(bio->bi_bdev->bd_inode->i_size >> 9)); > > > maxsector = bio->bi_bdev->bd_inode->i_size >> 9; > > > BLOCK/COMPAT_IOCTL.C: size = bdev->bd_inode->i_size; > > > return compat_put_u64(arg, bdev->bd_inode->i_size); > > > BLOCK/IOCTL.C: if (start + len > (bdev->bd_inode->i_size >> 9)) > > > size = bdev->bd_inode->i_size; > > > return put_u64(arg, bdev->bd_inode->i_size); > > > > > > The problem with this code is that if you read i_size without i_size_read > > > and the size wraps around 32 bits, for example from 0xffffffff to > > > 0x100000000 , there is a possibility on 32-bit machines to read an invalid > > > value (either 0 or 0x1ffffffff). Similarly, if you write i_size without > > > i_size_write, the readers can see intermediate invalid values. > > > > > > > > > The original problem that caused this investigation is the question, how a > > > block device driver can change the size of its device. Normal method (used > > > in a few drivers, including dm), consists of > > > mutex_lock(&inode->i_mutex); > > > i_size_write(inode, new_size); > > > mutex_unlock(&inode->i_mutex); > > > > Don't you just do > > > > set_capacity(gendisk, sectors); > > revalidate(gendisk); > > > > ?? > > > > NeilBrown > > revalidate_disk() has still the problem that it changes i_size without > holding i_mutex and other kernel parts (for example generic_file_llseek) > assume that if we hold the lock, i_size_can't be changed. generic_file_llseek is not used for block devices. They use block_llseek which uses i_size_read, so I think it is safe. > > The rules for accessing i_size must be specified and followed. I agree. However the rules can be different for different file systems and file types. A filesystem that used the generic_* function would need to only change i_size under i_mutex as you say. For block devices it appears that the rule is that it can only be changed under bd_mutex. For 'relay' (which you mentioned above), it seem the relevant mutex is the global relay_channels_mutex, though I didn't read the code thoroughly to be sure. It still would probably be useful to review all the i_size related code to ensure that it is safe, but you should not assume that everything follows the same rules. So first you need to work out the rule for a given subsystem, then audit it against that rule (and maybe document that rule if it isn't already documented!) NeilBrown > > Mikulas -- dm-devel mailing list dm-devel@xxxxxxxxxx https://www.redhat.com/mailman/listinfo/dm-devel
