Mike Anderson wrote:
Mike Christie <michaelc@xxxxxxxxxxx> wrote:
adding linux-scsi and Mike Anderson
David Strand wrote:
After updating to kernel 2.6.28 I found that when I performed some
cable break testing during device i/o, I would get unwanted device or
host resets. Ultimately I traced it back to this patch:
http://git.kernel.org/?p=linux/kernel/git/stable/linux-2.6.29.y.git;a=commit;h=224cb3e981f1b2f9f93dbd49eaef505d17d894c2
The call to blk_abort_queue causes the block layer to call
scsi_times_out for pending i/o, which can (or will) ultimately lead to
device, and/or bus and/or host resets, which of course cause all the
other devices significant disruption.
What driver were you using? I just did a work around for qla4xxx for
this (have not posted it yet). I added a scsi_times_out handler to the
driver so that if the IO was failed to a transport problem then the eh
does not run.
FC drivers already use fc_timed_out, but I think that will not work. The
FC driver could fail the IO then call fc_remote_port_delete. So the
failed IO could hit dm-mpath.c and that could call into the
scsi_times_out (which for fc drivers call into fc_timed_out) but the
fc_remote_port_delete has not been done yet, so the port_state is still
online so that kicks off the scsi eh.
For HA link transport failure cases the waking of scsi_eh should not
What is a HA link transport failure?
matter. For tgt link transport failures the waking of scsi_eh is not good.
Previous test runs with added debug I only saw a few case of going into the
abort routines, but maybe my test configs where not complete (timing of
the workqueues running will alter the outcome also). I will look into this
I think going into the abort routines is still bad. If are in the scsi
eh then all IO on that host is stopped. So if you had two ports coming
on that host, and if just one path is bad, now we cannot send IO on the
other path until the scsi eh is done running. This could be quick, but
for FC drivers we also do not just send an abort right away. If we have
transitioned the port state to blocked by this time, then drivers wait
for the port state to transition like this:
static void
qla2x00_block_error_handler(struct scsi_cmnd *cmnd)
{
struct Scsi_Host *shost = cmnd->device->host;
struct fc_rport *rport =
starget_to_rport(scsi_target(cmnd->device));
unsigned long flags;
spin_lock_irqsave(shost->host_lock, flags);
while (rport->port_state == FC_PORTSTATE_BLOCKED) {
spin_unlock_irqrestore(shost->host_lock, flags);
msleep(1000);
spin_lock_irqsave(shost->host_lock, flags);
}
spin_unlock_irqrestore(shost->host_lock, flags);
return;
}
So we are stuck in the scsi eh until the dev loss timeo fires. There is
a similar problem for some iscsi drivers.
more. The original described failure case of getting host resets is not
good though and would like to understand how we get this far.
For transport errors I do not think blk_abort_queue is needed anymore -
at least for scsi drivers. For FC almost every driver supports the
terminate_rport_io call back (just mptfc does not), so you can set the
fast io fail tmo to make sure all IO is failed quickly. For iscsi, we
have the replacement/recovery_timeout. And for SAS, I think there is a
timeout or the device/target/port is deleted, right?
Yes. (I believe there is an end case that others have discussed in the past
that path checkers or other requests without the fast_fail flag set may
wait until devloss).
That is not really there any more. Set the fast io fail tmo and IO is
failed before dev loss.
The exceptions are for mptfc (does not have a terminate rport io
callback) and for the scsi eh case like above where the scsi eh starts
up then the port is deleted (so we miss the fc_timed_out check) and then
drivers block until the port state transistions.
What was the reason for this change? I searched through my email from
this mailing list and could not find a discussion about it.
It seems like it would only make sense to call blk_abort_queue for maybe
some block drivers (does cciss or dasd need it) or maybe for device
errors. But it seems to be broken for the common multipath use cases.
One usage is to handle the case of slow multipath failover where devices
are still responsive on the transport, but are not completing IOs. We can
see a very long delay depending on IO timeout value vs. queue depth of the
target.
I did not get that part. What component is bad? If you change paths,
don't you just send IO to the same device? Is this that dasd setup? Or
does device above mean the target controller or can you access a
different logical unit through different ports on some multipath setups
(some sort of clustering magic?)?
And also for this problem, what type of failure is it? Are drivers
returning a DID_* error for this? Or is it some scsi error?
--
dm-devel mailing list
dm-devel@xxxxxxxxxx
https://www.redhat.com/mailman/listinfo/dm-devel
