Hi Andrew,
On Fri, 19 Sep 2008 14:33:44 -0700, Andrew Morton wrote:
> On Fri, 19 Sep 2008 10:48:54 -0400 (EDT)
> Kiyoshi Ueda <k-ueda@xxxxxxxxxxxxx> wrote:
>
> > This patch adds an interface to check lld's busy status
> > from the block layer.
> > This resolves a performance problem on request stacking devices below.
> >
> >
> > Some drivers like scsi mid layer stop dispatching request when
> > they detect busy state on its low-level device like host/bus/device.
> > It allows other requests to stay in the I/O scheduler's queue
> > for a chance of merging.
> >
> > Request stacking drivers like request-based dm should follow
> > the same logic.
> > However, there is no generic interface for the stacked device
> > to check if the underlying device(s) are busy.
> > If the request stacking driver dispatches and submits requests to
> > the busy underlying device, the requests will stay in
> > the underlying device's queue without a chance of merging.
> > This causes performance problem on burst I/O load.
> >
> > With this patch, busy state of the underlying device is exported
> > via the state flag of queue's backing_dev_info. So the request
> > stacking driver can check it and stop dispatching requests if busy.
> >
> > The underlying device driver must set/clear the flag appropriately:
> > ON: when the device driver can't process requests immediately.
> > OFF: when the device driver can process requests immediately,
> > including abnormal situations where the device driver needs
> > to kill all requests.
> >
> >
> > Signed-off-by: Kiyoshi Ueda <k-ueda@xxxxxxxxxxxxx>
> > Signed-off-by: Jun'ichi Nomura <j-nomura@xxxxxxxxxxxxx>
> > Cc: James Bottomley <James.Bottomley@xxxxxxxxxxxxxxxxxxxxx>
> > ---
> > include/linux/backing-dev.h | 8 ++++++++
> > mm/backing-dev.c | 12 ++++++++++++
> > 2 files changed, 20 insertions(+)
> >
> > Index: scsi-misc-2.6/include/linux/backing-dev.h
> > ===================================================================
> > --- scsi-misc-2.6.orig/include/linux/backing-dev.h
> > +++ scsi-misc-2.6/include/linux/backing-dev.h
> > @@ -26,6 +26,7 @@ enum bdi_state {
> > BDI_pdflush, /* A pdflush thread is working this device */
> > BDI_write_congested, /* The write queue is getting full */
> > BDI_read_congested, /* The read queue is getting full */
> > + BDI_lld_congested, /* The device/host is busy */
> > BDI_unused, /* Available bits start here */
> > };
> >
> > @@ -226,8 +227,15 @@ static inline int bdi_rw_congested(struc
> > (1 << BDI_write_congested));
> > }
> >
> > +static inline int bdi_lld_congested(struct backing_dev_info *bdi)
> > +{
> > + return bdi_congested(bdi, 1 << BDI_lld_congested);
> > +}
> > +
> > void clear_bdi_congested(struct backing_dev_info *bdi, int rw);
> > void set_bdi_congested(struct backing_dev_info *bdi, int rw);
> > +void clear_bdi_lld_congested(struct backing_dev_info *bdi);
> > +void set_bdi_lld_congested(struct backing_dev_info *bdi);
> > long congestion_wait(int rw, long timeout);
> >
> >
> > Index: scsi-misc-2.6/mm/backing-dev.c
> > ===================================================================
> > --- scsi-misc-2.6.orig/mm/backing-dev.c
> > +++ scsi-misc-2.6/mm/backing-dev.c
> > @@ -279,6 +279,18 @@ void set_bdi_congested(struct backing_de
> > }
> > EXPORT_SYMBOL(set_bdi_congested);
> >
> > +void clear_bdi_lld_congested(struct backing_dev_info *bdi)
> > +{
> > + clear_bit(BDI_lld_congested, &bdi->state);
> > +}
> > +EXPORT_SYMBOL_GPL(clear_bdi_lld_congested);
> > +
> > +void set_bdi_lld_congested(struct backing_dev_info *bdi)
> > +{
> > + set_bit(BDI_lld_congested, &bdi->state);
> > +}
> > +EXPORT_SYMBOL_GPL(set_bdi_lld_congested);
> > +
> > /**
> > * congestion_wait - wait for a backing_dev to become uncongested
> > * @rw: READ or WRITE
>
> Is this really the right way to do it?
I think so, but I may not understand what you mean correctly.
So please elaborate your concern if my explanation below doesn't
satisfy what you want to know.
> Back in the days when we first did the backing_dev_info.congested_fn()
> logic it was decided that there basically was no single place in which
> the congested state could be stored.
>
> So we ended up deciding that whenever a caller wants to know a
> backing_dev's congested status, it has to call in to the
> ->congested_fn() and that congested_fn would then call down into all
> the constituent low-level drivers/queues/etc asking each one if it is
> congested.
bdi_lld_congested() also does that using bdi_congested(), which calls
->congested_fn().
And only real device drivers (e.g. scsi, ide) set/clear the flag.
Stacking drivers like request-based dm don't.
So stacking drivers always check the BDI_lld_congested flag of
the bottom device of the device stack.
BDI_[write|read]_congested flags have been using for queue's
congestion, so that I/O queueing/merging can be proceeded even if
the lld is congested. So I added a new flag.
> I mean, as a simple example which is probably wrong - what happens if a
> single backing_dev is implemented via two different disks and
> controllers, and they both become congested and then one of them comes
> uncongested. Is there no way in which the above implemention can
> incorrectly flag the backing_dev as being uncongested?
Do you mean that "a single backing_dev via two disks/controllers" is
a dm device (e.g. a dm-multipath device having 2 paths, a dm-mirror
device having 2 disks)?
If so, dm doesn't set/clear the flag, and the decision, whether
the dm device itself is congested or not, depends on dm's target driver.
For example of dm-multipath,
o call bdi_lld_congested() for each path.
o if one of the paths are uncongested, dm-multipath will decide
the dm device is uncongested and dispatch incoming I/Os to
the uncongested path.
For example of dm-mirror,
o call bdi_lld_congested() for each disk.
o if the incoming I/O is READ, same logic as dm-multipath above.
if the incoming I/O is WRITE, dm-mirror will decide the dm device
is uncongested only when all disks are uncongested.
Thanks,
Kiyoshi Ueda
--
dm-devel mailing list
dm-devel@xxxxxxxxxx
https://www.redhat.com/mailman/listinfo/dm-devel
