Quick question...what RPM would I find udevsettle in? Doesn't appear to be installed on my system (RedHat Enterprise Linux 4), nor can I find reference to it on RedHat's site. Thanks, Rick -----Original Message----- From: dm-devel-bounces@xxxxxxxxxx [mailto:dm-devel-bounces@xxxxxxxxxx] On Behalf Of malahal@xxxxxxxxxx Sent: Sunday, February 17, 2008 2:47 AM To: dm-devel@xxxxxxxxxx Subject: Re: Multipath not rebuilding correctly on reboot Will udevsettle help here? Calling "udevsettle --timeout=60" prior to calling multipath.static in rc.sysinit may help. --Malahal. Benjamin Marzinski [bmarzins@xxxxxxxxxx] wrote: > On Thu, Feb 14, 2008 at 01:40:53PM -0500, Greene, Rick wrote: > > I tried Benjamin's suggestions, and with a little poking around I > > basically got nowhere. > > > > I did have to make one other adjustment to the system, I modified > > /etc/lvm/lvm.conf to only try activating the vg00 volume group (local > > disk) and not the vgftp volume group (built on the disk running through > > multipath). > > > > I'm still left with the same state, it takes that extra "multipath -v 2" > > to get everything fully activated. I do have that in rc.local at the > > moment, but I'm hoping someone can figure out what is going on so I > > don't have to have that extra step. > > > > Attached is the log file generated during the boot process, including > > the results of the extra step. If you look for lines starting with %%, > > you'll see comments showing what has generated each section of the long. > > > > Any further advice greatly appreciated, > > It seems that all your paths appear early enough to be managed by > rc.sysint. However, looking at the path info output for sde, sdf, sdg, > and sdh, it looks like multipath can't open their device nodes. I'm > assuming that it's because udev hasn't created them yet. In upstream > and RHEL5 there is code to wait up to five seconds for the device node > to be created. In RHEL4, that code is only run by multipathd. I can't > be sure that this is the cause of your problems, but it seems very likely. > > Besides putting sleeps into rc.sysinit, there's not much that can be > done without patching the code. If you are willing to patch the source > yourself, I've attached a patch. Otherwise, I can build a test rpm, > although maybe not till early next week, send out a link to it. > > Hope this helps > -Ben > > ===== path info sdh (mask 0x1f) ===== > bus = 1 > dev_t = 8:112 > size = 28452960 > vendor = HP > product = OPEN-E > rev = 2114 > h:b:t:l = 2:0:0:3 > tgt_node_name = 0x50060e80039c5a14 > # > # all paths : > # > 00040026_05:83 1:0:0:0 sda 8:0 [ready] HP /OPEN-E /2114 > 00040026_05:84 1:0:0:1 sdb 8:16 [ready] HP /OPEN-E /2114 > 00040026_05:85 1:0:0:2 sdc 8:32 [ready] HP /OPEN-E /2114 > 00040026_05:86 1:0:0:3 sdd 8:48 [ready] HP /OPEN-E /2114 > 2:0:0:0 sde 8:64 [faulty] HP /OPEN-E /2114 > 2:0:0:1 sdf 8:80 [faulty] HP /OPEN-E /2114 > 2:0:0:2 sdg 8:96 [faulty] HP /OPEN-E /2114 > 2:0:0:3 sdh 8:112 [faulty] HP /OPEN-E /2114 > > > Rick > > > > -----Original Message----- > > From: dm-devel-bounces@xxxxxxxxxx [mailto:dm-devel-bounces@xxxxxxxxxx] > > On Behalf Of Benjamin Marzinski > > Sent: Tuesday, February 12, 2008 5:22 PM > > To: device-mapper development > > Subject: Re: Multipath not rebuilding correctly on reboot > > > > On Thu, Jan 31, 2008 at 03:20:04PM -0500, Greene, Rick wrote: > > > Now that I seem to have multipath and my XP 1024 working together, > > I've > > > found a new issue. Someone recently had a similar thread going, but I > > > saw no ultimate resolution. > > > > > > My problem is that when I reboot my server, the multipath > > configuration > > > is not coming back the way it was before. I moved the two external > > > tools I use to find the UID into /etc (they had bin in /usr/bin and > > > /sbin), updated the multipath.conf file (and one of the scripts) to > > > reflect this, but odd things are still happening. > > > > > > Attached is initial_view.txt, which shows what multipath is coming up > > > with when I do the commands shown (the bulk of the file is multipath > > -v3 > > > output, but at the bottom of the file is a multipath -ll output as > > > well). It (seems to) correctly shows that I have 4 disks, each > > visible > > > via two separate paths. > > > > > > After I reboot, however, I get different results. Once it showed 4 > > > paths for mpath0, and 2 paths for mpath1, 2, and 3. Next time it > > > correctly showed mpath0, mpath1, and mpath3, but didn't show mpath2 at > > > all. On the next attempt I got everything correct, and the very next > > > one only showed mpath0 and mpath1. > > > > > > The post_reboot.txt file shows the contents of the /var/log/boot.log > > > file and the output of the dmesg command, along with the "multipath > > -ll" > > > view from the most recent reboot. > > > > > > I then manually did a "multipath -v2" and the missing two paths then > > > came back. The file manual_run.txt shows those results plus the > > updated > > > "multipath -ll". > > > > > > Do I need to just make my own /etc/init.d script to do a "multipath > > -v2" > > > at the end of booting to make sure it all gets covered, along with the > > > requisite LVM & mount commands to get the VG that is on these disks > > > working right? > > > > Hopefully, you can just add the line > > > > multipath -v 0 > > > > to /etc/rc.local and fix this. However, if you want to dig into > > what's going wrong: > > > > There are two places were multipath gets called to create devices during > > bootup. One is in /etc/rc.sysinit and one in > > /etc/dev.d/block/multipath.dev. /etc/rc.sysinit will always be run as > > one of the first things during the boot process, and it just calls > > multipath.static -v 0, which should correctly set up multipath devices > > on all of the available paths. /etc/dev.d/block/multipath.dev gets > > called by udev, and is a lot more suspect. > > > > If you feel confortable editting boot scripts, you can do some debugging > > to figure out what's going on. > > > > in /etc/rc.sysinit (assuming you aren't using md or raid), you can > > change > > the first line with: > > /sbin/multipath.static -v 0 > > to: > > /sbin/multipath.static -v 3 >> /tmp/multipath_boot_log 2>&1 > > > > the other lines that call multipath.static are only run if you have > > the files /etc/raidtab or /etc/mdadm.conf, which you probably don't. > > > > in /etc/dev.d/block/multipath.dev just add the following line right > > after the #!/bin/sh line: > > > > echo "${ACTION} ${DEVPATH}" >> /tmp/multipath_boot_log > > > > Then reboot and look at /tmp/multipath_boot_log > > > > You should see something that looks like the output of running > > # multipath -v 3 > > along with a bunch of lines like: > > > > add /block/md0 > > add /block/loop1 > > add /block/loop0 > > add /block/dm-7 > > > > The multipath run is from rc.sysinit, and the "add" lines are devices > > that udev is trying to create a multipath device on. On systems where > > everthing comes up fine during boot up, all of the devices that aren't > > dealt with by the multipath call in rc.sysinit should be added by udev. > > > > I'm assuming that this won't be the case on your box. If udev isn't > > running /etc/dev.d/block/multipath.dev, there's not much you can do > > to fix it, besides filing a bug against udev. However you may be able > > to > > make it more likely that your scsi devices will all be up by the time > > rc.sysinit is run. If your device drivers aren't getting loaded by the > > initrd, you can add them to /etc/modprobe.conf, run mkinitrd. If you do > > this, it's always wise to back up your existing initrd, and make sure > > that grub can boot with it. > > > > Otherwise, just try adding the line to rc.local > > > > Hope this helps > > > > -Ben > > > > > Thanks in advance, > > > Rick > > > > > > > > > > > > > Content-Description: initial_view.txt > > > # service multipathd stop > > > # multipath -F > > > # service multipathd start > > > # multipath -v3 > > > load path identifiers cache > > > # > > > # all paths in cache : > > > # > > > 00040026_05:83 1:0:0:0 sda 8:0 HP /OPEN-E /2114 > > > 00040026_05:84 1:0:0:1 sdb 8:16 HP /OPEN-E /2114 > > > 00040026_05:85 1:0:0:2 sdc 8:32 HP /OPEN-E /2114 > > > 00040026_05:86 1:0:0:3 sdd 8:48 HP /OPEN-E /2114 > > > 00040026_05:83 2:0:0:0 sde 8:64 HP /OPEN-E /2114 > > > 00040026_05:84 2:0:0:1 sdf 8:80 HP /OPEN-E /2114 > > > 00040026_05:85 2:0:0:2 sdg 8:96 HP /OPEN-E /2114 > > > 00040026_05:86 2:0:0:3 sdh 8:112 HP /OPEN-E /2114 > > > cciss!c0d0 blacklisted > > > cciss!c0d1 blacklisted > > > dm-0 blacklisted > > > dm-1 blacklisted > > > dm-2 blacklisted > > > dm-3 blacklisted > > > dm-4 blacklisted > > > dm-5 blacklisted > > > dm-6 blacklisted > > > dm-7 blacklisted > > > fd0 blacklisted > > > hda blacklisted > > > md0 blacklisted > > > ram0 blacklisted > > > ram10 blacklisted > > > ram11 blacklisted > > > ram12 blacklisted > > > ram13 blacklisted > > > ram14 blacklisted > > > ram15 blacklisted > > > ram1 blacklisted > > > ram2 blacklisted > > > ram3 blacklisted > > > ram4 blacklisted > > > ram5 blacklisted > > > ram6 blacklisted > > > ram7 blacklisted > > > ram8 blacklisted > > > ram9 blacklisted > > > ===== path info sda (mask 0x1f) ===== > > > bus = 1 > > > dev_t = 8:0 > > > size = 28452960 > > > vendor = HP > > > product = OPEN-E > > > rev = 2114 > > > h:b:t:l = 1:0:0:0 > > > tgt_node_name = 0x50060e80039c5a04 > > > serial = 40026 > > > path checker = tur (controler setting) > > > state = 2 > > > getprio = /bin/true (internal default) > > > prio = 0 > > > uid = 00040026_05:83 (cache) > > > ===== path info sdb (mask 0x1f) ===== > > > bus = 1 > > > dev_t = 8:16 > > > size = 28452960 > > > vendor = HP > > > product = OPEN-E > > > rev = 2114 > > > h:b:t:l = 1:0:0:1 > > > tgt_node_name = 0x50060e80039c5a04 > > > serial = 40026 > > > path checker = tur (controler setting) > > > state = 2 > > > getprio = /bin/true (internal default) > > > prio = 0 > > > uid = 00040026_05:84 (cache) > > > ===== path info sdc (mask 0x1f) ===== > > > bus = 1 > > > dev_t = 8:32 > > > size = 28452960 > > > vendor = HP > > > product = OPEN-E > > > rev = 2114 > > > h:b:t:l = 1:0:0:2 > > > tgt_node_name = 0x50060e80039c5a04 > > > serial = 40026 > > > path checker = tur (controler setting) > > > state = 2 > > > getprio = /bin/true (internal default) > > > prio = 0 > > > uid = 00040026_05:85 (cache) > > > ===== path info sdd (mask 0x1f) ===== > > > bus = 1 > > > dev_t = 8:48 > > > size = 28452960 > > > vendor = HP > > > product = OPEN-E > > > rev = 2114 > > > h:b:t:l = 1:0:0:3 > > > tgt_node_name = 0x50060e80039c5a04 > > > serial = 40026 > > > path checker = tur (controler setting) > > > state = 2 > > > getprio = /bin/true (internal default) > > > prio = 0 > > > uid = 00040026_05:86 (cache) > > > ===== path info sde (mask 0x1f) ===== > > > bus = 1 > > > dev_t = 8:64 > > > size = 28452960 > > > vendor = HP > > > product = OPEN-E > > > rev = 2114 > > > h:b:t:l = 2:0:0:0 > > > tgt_node_name = 0x50060e80039c5a14 > > > serial = 40026 > > > path checker = tur (controler setting) > > > state = 2 > > > getprio = /bin/true (internal default) > > > prio = 0 > > > uid = 00040026_05:83 (cache) > > > ===== path info sdf (mask 0x1f) ===== > > > bus = 1 > > > dev_t = 8:80 > > > size = 28452960 > > > vendor = HP > > > product = OPEN-E > > > rev = 2114 > > > h:b:t:l = 2:0:0:1 > > > tgt_node_name = 0x50060e80039c5a14 > > > serial = 40026 > > > path checker = tur (controler setting) > > > state = 2 > > > getprio = /bin/true (internal default) > > > prio = 0 > > > uid = 00040026_05:84 (cache) > > > ===== path info sdg (mask 0x1f) ===== > > > bus = 1 > > > dev_t = 8:96 > > > size = 28452960 > > > vendor = HP > > > product = OPEN-E > > > rev = 2114 > > > h:b:t:l = 2:0:0:2 > > > tgt_node_name = 0x50060e80039c5a14 > > > serial = 40026 > > > path checker = tur (controler setting) > > > state = 2 > > > getprio = /bin/true (internal default) > > > prio = 0 > > > uid = 00040026_05:85 (cache) > > > ===== path info sdh (mask 0x1f) ===== > > > bus = 1 > > > dev_t = 8:112 > > > size = 28452960 > > > vendor = HP > > > product = OPEN-E > > > rev = 2114 > > > h:b:t:l = 2:0:0:3 > > > tgt_node_name = 0x50060e80039c5a14 > > > serial = 40026 > > > path checker = tur (controler setting) > > > state = 2 > > > getprio = /bin/true (internal default) > > > prio = 0 > > > uid = 00040026_05:86 (cache) > > > # > > > # all paths : > > > # > > > 00040026_05:83 1:0:0:0 sda 8:0 [ready] HP /OPEN-E > > /2114 > > > 00040026_05:84 1:0:0:1 sdb 8:16 [ready] HP /OPEN-E > > /2114 > > > 00040026_05:85 1:0:0:2 sdc 8:32 [ready] HP /OPEN-E > > /2114 > > > 00040026_05:86 1:0:0:3 sdd 8:48 [ready] HP /OPEN-E > > /2114 > > > 00040026_05:83 2:0:0:0 sde 8:64 [ready] HP /OPEN-E > > /2114 > > > 00040026_05:84 2:0:0:1 sdf 8:80 [ready] HP /OPEN-E > > /2114 > > > 00040026_05:85 2:0:0:2 sdg 8:96 [ready] HP /OPEN-E > > /2114 > > > 00040026_05:86 2:0:0:3 sdh 8:112 [ready] HP /OPEN-E > > /2114 > > > Initialized new bindings file [/var/lib/multipath/bindings] > > > No matching wwid [00040026_05:83] in bindings file. > > > Created new binding [mpath0] for WWID [00040026_05:83] > > > pgpolicy = multibus (controler setting) > > > selector = round-robin 0 (internal default) > > > features = 0 (internal default) > > > hwhandler = 0 (internal default) > > > rr_weight = 2 (config file default) > > > rr_min_io = 100 (config file default) > > > no_path_retry = -1 (config file default) > > > pg_timeout = NONE (internal default) > > > 0 28452960 multipath 0 0 1 1 round-robin 0 2 1 8:0 100 8:64 100 > > > set ACT_CREATE: map does not exists > > > message mpath0 0 switch_group 1 > > > > > > create: mpath0 (00040026_05:83) > > > [size=13 GB][features="0"][hwhandler="0"] > > > \_ round-robin 0 > > > \_ 1:0:0:0 sda 8:0 [ready] > > > \_ 2:0:0:0 sde 8:64 [ready] > > > > > > reloading features > > > No matching wwid [00040026_05:84] in bindings file. > > > Created new binding [mpath1] for WWID [00040026_05:84] > > > pgpolicy = multibus (controler setting) > > > selector = round-robin 0 (internal default) > > > features = 0 (internal default) > > > hwhandler = 0 (internal default) > > > rr_weight = 2 (config file default) > > > rr_min_io = 100 (config file default) > > > no_path_retry = -1 (config file default) > > > pg_timeout = NONE (internal default) > > > 0 28452960 multipath 0 0 1 1 round-robin 0 2 1 8:16 100 8:80 100 > > > set ACT_CREATE: map does not exists > > > message mpath1 0 switch_group 1 > > > > > > create: mpath1 (00040026_05:84) > > > [size=13 GB][features="0"][hwhandler="0"] > > > \_ round-robin 0 > > > \_ 1:0:0:1 sdb 8:16 [ready] > > > \_ 2:0:0:1 sdf 8:80 [ready] > > > > > > reloading features > > > No matching wwid [00040026_05:85] in bindings file. > > > Created new binding [mpath2] for WWID [00040026_05:85] > > > pgpolicy = multibus (controler setting) > > > selector = round-robin 0 (internal default) > > > features = 0 (internal default) > > > hwhandler = 0 (internal default) > > > rr_weight = 2 (config file default) > > > rr_min_io = 100 (config file default) > > > no_path_retry = -1 (config file default) > > > pg_timeout = NONE (internal default) > > > 0 28452960 multipath 0 0 1 1 round-robin 0 2 1 8:32 100 8:96 100 > > > set ACT_CREATE: map does not exists > > > message mpath2 0 switch_group 1 > > > > > > create: mpath2 (00040026_05:85) > > > [size=13 GB][features="0"][hwhandler="0"] > > > \_ round-robin 0 > > > \_ 1:0:0:2 sdc 8:32 [ready] > > > \_ 2:0:0:2 sdg 8:96 [ready] > > > > > > reloading features > > > No matching wwid [00040026_05:86] in bindings file. > > > Created new binding [mpath3] for WWID [00040026_05:86] > > > pgpolicy = multibus (controler setting) > > > selector = round-robin 0 (internal default) > > > features = 0 (internal default) > > > hwhandler = 0 (internal default) > > > rr_weight = 2 (config file default) > > > rr_min_io = 100 (config file default) > > > no_path_retry = -1 (config file default) > > > pg_timeout = NONE (internal default) > > > 0 28452960 multipath 0 0 1 1 round-robin 0 2 1 8:48 100 8:112 100 > > > set ACT_CREATE: map does not exists > > > message mpath3 0 switch_group 1 > > > > > > create: mpath3 (00040026_05:86) > > > [size=13 GB][features="0"][hwhandler="0"] > > > \_ round-robin 0 > > > \_ 1:0:0:3 sdd 8:48 [ready] > > > \_ 2:0:0:3 sdh 8:112 [ready] > > > > > > reloading features > > > > > > # multipath -ll > > > mpath2 (00040026_05:85) > > > [size=13 GB][features="0"][hwhandler="0"] > > > \_ round-robin 0 [active] > > > \_ 1:0:0:2 sdc 8:32 [active][ready] > > > \_ 2:0:0:2 sdg 8:96 [active][ready] > > > > > > mpath1 (00040026_05:84) > > > [size=13 GB][features="0"][hwhandler="0"] > > > \_ round-robin 0 [active] > > > \_ 1:0:0:1 sdb 8:16 [active][ready] > > > \_ 2:0:0:1 sdf 8:80 [active][ready] > > > > > > mpath0 (00040026_05:83) > > > [size=13 GB][features="0"][hwhandler="0"] > > > \_ round-robin 0 [active] > > > \_ 1:0:0:0 sda 8:0 [active][ready] > > > \_ 2:0:0:0 sde 8:64 [active][ready] > > > > > > mpath3 (00040026_05:86) > > > [size=13 GB][features="0"][hwhandler="0"] > > > \_ round-robin 0 [active] > > > \_ 1:0:0:3 sdd 8:48 [active][ready] > > > \_ 2:0:0:3 sdh 8:112 [active][ready] > > > > Content-Description: post_reboot.txt > > > # dmesg > > > Bootdata ok (command line is ro root=/dev/vg00/root rhgb quiet) > > > Linux version 2.6.9-55.ELsmp (brewbuilder@xxxxxxxxxxxxxxxxxxxxxxxxxxx) > > (gcc version 3.4.6 20060404 (Red Hat 3.4.6-3)) #1 SMP Fri Apr 20 > > 16:36:54 EDT 2007 > > > BIOS-provided physical RAM map: > > > BIOS-e820: 0000000000000000 - 000000000009f400 (usable) > > > BIOS-e820: 000000000009f400 - 00000000000a0000 (reserved) > > > BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved) > > > BIOS-e820: 0000000000100000 - 00000000bfff3000 (usable) > > > BIOS-e820: 00000000bfff3000 - 00000000bfffb000 (ACPI data) > > > BIOS-e820: 00000000bfffb000 - 00000000c0000000 (reserved) > > > BIOS-e820: 00000000fec00000 - 00000000fed00000 (reserved) > > > BIOS-e820: 00000000fee00000 - 00000000fee10000 (reserved) > > > BIOS-e820: 00000000ffc00000 - 0000000100000000 (reserved) > > > ACPI: RSDP (v002 HP ) @ > > 0x00000000000f4f00 > > > ACPI: XSDT (v001 HP P51 0x00000002 ? 0x0000162e) @ > > 0x00000000bfff3300 > > > ACPI: FADT (v003 HP P51 0x00000002 ? 0x0000162e) @ > > 0x00000000bfff3380 > > > ACPI: SPCR (v001 HP SPCRRBSU 0x00000001 ? 0x0000162e) @ > > 0x00000000bfff3140 > > > ACPI: MCFG (v001 HP ProLiant 0x00000001 0x00000000) @ > > 0x00000000bfff31c0 > > > ACPI: MADT (v001 HP 00000083 0x00000002 0x00000000) @ > > 0x00000000bfff3200 > > > ACPI: SSDT (v001 HP SSDTP 0x00000001 INTL 0x20030228) @ > > 0x00000000bfff8000 > > > ACPI: DSDT (v001 HP DSDT 0x00000001 INTL 0x20030228) @ > > 0x0000000000000000 > > > No NUMA configuration found > > > Faking a node at 0000000000000000-00000000bfff3000 > > > Bootmem setup node 0 0000000000000000-00000000bfff3000 > > > On node 0 totalpages: 786419 > > > DMA zone: 4096 pages, LIFO batch:1 > > > Normal zone: 782323 pages, LIFO batch:16 > > > HighMem zone: 0 pages, LIFO batch:1 > > > DMI 2.3 present. > > > ACPI: PM-Timer IO Port: 0x908 > > > ACPI: Local APIC address 0xfee00000 > > > ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled) > > > Processor #0 15:4 APIC version 16 > > > ACPI: LAPIC (acpi_id[0x02] lapic_id[0x02] disabled) > > > ACPI: LAPIC (acpi_id[0x04] lapic_id[0x04] disabled) > > > ACPI: LAPIC (acpi_id[0x06] lapic_id[0x06] enabled) > > > Processor #6 15:4 APIC version 16 > > > ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled) > > > Processor #1 15:4 APIC version 16 > > > ACPI: LAPIC (acpi_id[0x03] lapic_id[0x03] disabled) > > > ACPI: LAPIC (acpi_id[0x05] lapic_id[0x05] disabled) > > > ACPI: LAPIC (acpi_id[0x07] lapic_id[0x07] enabled) > > > Processor #7 15:4 APIC version 16 > > > ACPI: LAPIC_NMI (acpi_id[0xff] dfl dfl lint[0x1]) > > > Setting APIC routing to flat > > > ACPI: IOAPIC (id[0x08] address[0xfec00000] gsi_base[0]) > > > IOAPIC[0]: apic_id 8, version 32, address 0xfec00000, GSI 0-23 > > > ACPI: IOAPIC (id[0x09] address[0xfec80000] gsi_base[24]) > > > IOAPIC[1]: apic_id 9, version 32, address 0xfec80000, GSI 24-47 > > > ACPI: IOAPIC (id[0x0a] address[0xfec80400] gsi_base[48]) > > > IOAPIC[2]: apic_id 10, version 32, address 0xfec80400, GSI 48-71 > > > ACPI: IOAPIC (id[0x0b] address[0xfec84000] gsi_base[72]) > > > IOAPIC[3]: apic_id 11, version 32, address 0xfec84000, GSI 72-95 > > > ACPI: IOAPIC (id[0x0c] address[0xfec84400] gsi_base[96]) > > > IOAPIC[4]: apic_id 12, version 32, address 0xfec84400, GSI 96-119 > > > ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 high edge) > > > ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level) > > > ACPI: IRQ0 used by override. > > > ACPI: IRQ2 used by override. > > > ACPI: IRQ9 used by override. > > > Using ACPI (MADT) for SMP configuration information > > > Allocating PCI resources starting at c4000000 (gap: c0000000:3ec00000) > > > Checking aperture... > > > Built 1 zonelists > > > Kernel command line: ro root=/dev/vg00/root rhgb quiet console=tty0 > > > Initializing CPU#0 > > > PID hash table entries: 4096 (order: 12, 131072 bytes) > > > time.c: Using 3.579545 MHz PM timer. > > > time.c: Detected 3400.312 MHz processor. > > > Console: colour VGA+ 80x25 > > > Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes) > > > Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes) > > > Memory: 3089236k/3145676k available (2112k kernel code, 0k reserved, > > 1305k data, 208k init) > > > Calibrating delay using timer specific routine.. 6807.48 BogoMIPS > > (lpj=3403744) > > > Security Scaffold v1.0.0 initialized > > > SELinux: Initializing. > > > SELinux: Starting in permissive mode > > > There is already a security framework initialized, register_security > > failed. > > > selinux_register_security: Registering secondary module capability > > > Capability LSM initialized as secondary > > > Mount-cache hash table entries: 256 (order: 0, 4096 bytes) > > > CPU: Trace cache: 12K uops, L1 D cache: 16K > > > CPU: L2 cache: 1024K > > > using mwait in idle threads. > > > CPU0: Initial APIC ID: 0, Physical Processor ID: 0 > > > Using IO APIC NMI watchdog > > > CPU: Trace cache: 12K uops, L1 D cache: 16K > > > CPU: L2 cache: 1024K > > > CPU0: Initial APIC ID: 0, Physical Processor ID: 0 > > > CPU0: Intel(R) Xeon(TM) CPU 3.40GHz stepping 01 > > > per-CPU timeslice cutoff: 1023.90 usecs. > > > task migration cache decay timeout: 1 msecs. > > > Booting processor 1/6 rip 6000 rsp 10037e05f58 > > > Initializing CPU#1 > > > Calibrating delay using timer specific routine.. 6799.32 BogoMIPS > > (lpj=3399660) > > > CPU: Trace cache: 12K uops, L1 D cache: 16K > > > CPU: L2 cache: 1024K > > > CPU1: Initial APIC ID: 6, Physical Processor ID: 3 > > > Intel(R) Xeon(TM) CPU 3.40GHz stepping 01 > > > Booting processor 2/1 rip 6000 rsp 10037e3df58 > > > Initializing CPU#2 > > > Calibrating delay using timer specific routine.. 6799.31 BogoMIPS > > (lpj=3399655) > > > CPU: Trace cache: 12K uops, L1 D cache: 16K > > > CPU: L2 cache: 1024K > > > CPU2: Initial APIC ID: 1, Physical Processor ID: 0 > > > Intel(R) Xeon(TM) CPU 3.40GHz stepping 01 > > > Booting processor 3/7 rip 6000 rsp 100016f3f58 > > > Initializing CPU#3 > > > Calibrating delay using timer specific routine.. 6799.18 BogoMIPS > > (lpj=3399591) > > > CPU: Trace cache: 12K uops, L1 D cache: 16K > > > CPU: L2 cache: 1024K > > > CPU3: Initial APIC ID: 7, Physical Processor ID: 3 > > > Intel(R) Xeon(TM) CPU 3.40GHz stepping 01 > > > Total of 4 processors activated (27205.30 BogoMIPS). > > > activating NMI Watchdog ... done. > > > testing NMI watchdog ... OK. > > > Using local APIC timer interrupts. > > > Detected 12.501 MHz APIC timer. > > > checking TSC synchronization across 4 CPUs: passed. > > > Brought up 4 CPUs > > > time.c: Using PIT/TSC based timekeeping. > > > checking if image is initramfs... it is > > > NET: Registered protocol family 16 > > > PCI: Using configuration type 1 > > > PCI: Using MMCONFIG at e0000000 > > > mtrr: v2.0 (20020519) > > > mtrr: your CPUs had inconsistent fixed MTRR settings > > > mtrr: probably your BIOS does not setup all CPUs. > > > mtrr: corrected configuration. > > > ACPI: Subsystem revision 20040816 > > > ACPI: Interpreter enabled > > > ACPI: Using IOAPIC for interrupt routing > > > ACPI: PCI Root Bridge [PCI0] (00:00) > > > PCI: Probing PCI hardware (bus 00) > > > PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.1 > > > PCI: PXH quirk detected, disabling MSI for SHPC device > > > PCI: PXH quirk detected, disabling MSI for SHPC device > > > PCI: PXH quirk detected, disabling MSI for SHPC device > > > PCI: PXH quirk detected, disabling MSI for SHPC device > > > PCI: Transparent bridge - 0000:00:1e.0 > > > ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] > > > ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.IP2P._PRT] > > > ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PTA0._PRT] > > > ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PTA0.PCXA._PRT] > > > ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PTA0.PCXB._PRT] > > > ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PTC0._PRT] > > > ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PTC0.PCXC._PRT] > > > ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PTC0.PCXD._PRT] > > > ACPI: PCI Interrupt Link [LNKA] (IRQs *5 7 10 11) > > > ACPI: PCI Interrupt Link [LNKB] (IRQs *5 7 10 11) > > > ACPI: PCI Interrupt Link [LNKC] (IRQs *5 7 10 11) > > > ACPI: PCI Interrupt Link [LNKD] (IRQs *5 7 10 11) > > > ACPI: PCI Interrupt Link [LNKE] (IRQs 5 7 10 11) *0, disabled. > > > ACPI: PCI Interrupt Link [LNKF] (IRQs *5 7 10 11) > > > ACPI: PCI Interrupt Link [LNKG] (IRQs *5 7 10 11) > > > ACPI: PCI Interrupt Link [LNKH] (IRQs *5 7 10 11) > > > usbcore: registered new driver usbfs > > > usbcore: registered new driver hub > > > PCI: Using ACPI for IRQ routing > > > GSI 16 sharing vector 0xA9 and IRQ 16 > > > ACPI: PCI Interrupt 0000:00:02.0[A] -> GSI 16 (level, low) -> IRQ 169 > > > ACPI: PCI Interrupt 0000:00:06.0[A] -> GSI 16 (level, low) -> IRQ 169 > > > ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 16 (level, low) -> IRQ 169 > > > GSI 17 sharing vector 0xB1 and IRQ 17 > > > ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 177 > > > GSI 18 sharing vector 0xB9 and IRQ 18 > > > ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 185 > > > ACPI: PCI Interrupt 0000:00:1d.3[A] -> GSI 16 (level, low) -> IRQ 169 > > > GSI 19 sharing vector 0xC1 and IRQ 19 > > > ACPI: PCI Interrupt 0000:00:1d.7[D] -> GSI 23 (level, low) -> IRQ 193 > > > ACPI: PCI interrupt 0000:00:1f.1[A]: no GSI > > > GSI 20 sharing vector 0xC9 and IRQ 20 > > > ACPI: PCI Interrupt 0000:03:01.0[A] -> GSI 25 (level, low) -> IRQ 201 > > > GSI 21 sharing vector 0xD1 and IRQ 21 > > > ACPI: PCI Interrupt 0000:03:01.1[B] -> GSI 26 (level, low) -> IRQ 209 > > > GSI 22 sharing vector 0xD9 and IRQ 22 > > > ACPI: PCI Interrupt 0000:04:03.0[A] -> GSI 51 (level, low) -> IRQ 217 > > > GSI 23 sharing vector 0xE1 and IRQ 23 > > > ACPI: PCI Interrupt 0000:06:02.0[A] -> GSI 78 (level, low) -> IRQ 225 > > > GSI 24 sharing vector 0xE9 and IRQ 24 > > > ACPI: PCI Interrupt 0000:07:04.0[A] -> GSI 74 (level, low) -> IRQ 233 > > > GSI 25 sharing vector 0x32 and IRQ 25 > > > ACPI: PCI Interrupt 0000:07:05.0[A] -> GSI 73 (level, low) -> IRQ 50 > > > GSI 26 sharing vector 0x3A and IRQ 26 > > > ACPI: PCI Interrupt 0000:0a:01.0[A] -> GSI 97 (level, low) -> IRQ 58 > > > GSI 27 sharing vector 0x42 and IRQ 27 > > > ACPI: PCI Interrupt 0000:0a:01.1[B] -> GSI 98 (level, low) -> IRQ 66 > > > GSI 28 sharing vector 0x4A and IRQ 28 > > > ACPI: PCI Interrupt 0000:01:04.0[A] -> GSI 21 (level, low) -> IRQ 74 > > > GSI 29 sharing vector 0x52 and IRQ 29 > > > ACPI: PCI Interrupt 0000:01:04.2[B] -> GSI 22 (level, low) -> IRQ 82 > > > PCI-DMA: Disabling IOMMU. > > > IA32 emulation $Id: sys_ia32.c,v 1.32 2002/03/24 13:02:28 ak Exp $ > > > audit: initializing netlink socket (disabled) > > > audit(1201791896.599:1): initialized > > > Total HugeTLB memory allocated, 0 > > > VFS: Disk quotas dquot_6.5.1 > > > Dquot-cache hash table entries: 512 (order 0, 4096 bytes) > > > SELinux: Registering netfilter hooks > > > Initializing Cryptographic API > > > ksign: Installing public key data > > > Loading keyring > > > - Added public key B7CA3C9BE2FAFC39 > > > - User ID: Red Hat, Inc. (Kernel Module GPG key) > > > pci_hotplug: PCI Hot Plug PCI Core version: 0.5 > > > ACPI: Processor [CPU0] (supports C1) > > > ACPI: Processor [CPU1] (supports C1) > > > ACPI: Processor [CPU2] (supports C1) > > > ACPI: Processor [CPU3] (supports C1) > > > ACPI: Thermal Zone [THM0] (8 C) > > > Real Time Clock Driver v1.12 > > > Linux agpgart interface v0.100 (c) Dave Jones > > > serio: i8042 AUX port at 0x60,0x64 irq 12 > > > serio: i8042 KBD port at 0x60,0x64 irq 1 > > > Serial: 8250/16550 driver $Revision: 1.90 $ 68 ports, IRQ sharing > > enabled > > > ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A > > > ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A > > > RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize > > > divert: not allocating divert_blk for non-ethernet device lo > > > Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 > > > ide: Assuming 33MHz system bus speed for PIO modes; override with > > idebus=xx > > > ICH5: IDE controller at PCI slot 0000:00:1f.1 > > > PCI: Enabling device 0000:00:1f.1 (0005 -> 0007) > > > ACPI: PCI interrupt 0000:00:1f.1[A]: no GSI > > > ICH5: chipset revision 2 > > > ICH5: not 100% native mode: will probe irqs later > > > ide0: BM-DMA at 0x0500-0x0507, BIOS settings: hda:DMA, hdb:pio > > > ide1: BM-DMA at 0x0508-0x050f, BIOS settings: hdc:pio, hdd:pio > > > Probing IDE interface ide0... > > > hda: DV-28E-N, ATAPI CD/DVD-ROM drive > > > Using cfq io scheduler > > > ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 > > > Probing IDE interface ide1... > > > Probing IDE interface ide1... > > > Probing IDE interface ide2... > > > Probing IDE interface ide3... > > > Probing IDE interface ide4... > > > Probing IDE interface ide5... > > > hda: ATAPI 24X DVD-ROM drive, 256kB Cache, UDMA(33) > > > Uniform CD-ROM driver Revision: 3.20 > > > ide-floppy driver 0.99.newide > > > usbcore: registered new driver hiddev > > > usbcore: registered new driver usbhid > > > drivers/usb/input/hid-core.c: v2.0:USB HID core driver > > > mice: PS/2 mouse device common for all mice > > > input: AT Translated Set 2 keyboard on isa0060/serio0 > > > input: PS/2 Generic Mouse on isa0060/serio1 > > > md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27 > > > NET: Registered protocol family 2 > > > IP route cache hash table entries: 131072 (order: 8, 1048576 bytes) > > > TCP established hash table entries: 262144 (order: 10, 4194304 bytes) > > > TCP bind hash table entries: 262144 (order: 10, 4194304 bytes) > > > TCP: Hash tables configured (established 262144 bind 262144) > > > Initializing IPsec netlink socket > > > NET: Registered protocol family 1 > > > NET: Registered protocol family 17 > > > cpufreq: CPU0 - ACPI performance management activated. > > > cpufreq: *P0: 3400 MHz, 103000 mW, 100 uS > > > cpufreq: P1: 2800 MHz, 77469 mW, 100 uS > > > cpufreq: CPU1 - ACPI performance management activated. > > > cpufreq: *P0: 3400 MHz, 103000 mW, 100 uS > > > cpufreq: P1: 2800 MHz, 77469 mW, 100 uS > > > cpufreq: CPU2 - ACPI performance management activated. > > > cpufreq: *P0: 3400 MHz, 103000 mW, 100 uS > > > cpufreq: P1: 2800 MHz, 77469 mW, 100 uS > > > cpufreq: CPU3 - ACPI performance management activated. > > > cpufreq: *P0: 3400 MHz, 103000 mW, 100 uS > > > cpufreq: P1: 2800 MHz, 77469 mW, 100 uS > > > ACPI wakeup devices: > > > > > > ACPI: (supports S0 S4 S5) > > > Freeing unused kernel memory: 208k freed > > > SCSI subsystem initialized > > > HP CISS Driver (v 2.6.14.RH2) > > > cciss: Device 0x46 has been found at bus 4 dev 3 func 0 > > > ACPI: PCI Interrupt 0000:04:03.0[A] -> GSI 51 (level, low) -> IRQ 217 > > > cciss: using DAC cycles > > > blocks= 71122559 block_size= 512 > > > heads= 255, sectors= 32, cylinders= 8716 > > > > > > blocks= 71122559 block_size= 512 > > > heads= 255, sectors= 32, cylinders= 8716 > > > > > > blocks= 71122559 block_size= 512 > > > heads= 255, sectors= 32, cylinders= 8716 > > > > > > cciss/c0d0: p1 p2 > > > blocks= 71122559 block_size= 512 > > > heads= 255, sectors= 32, cylinders= 8716 > > > > > > cciss/c0d1: unknown partition table > > > device-mapper: 4.5.5-ioctl (2006-12-01) initialised: > > dm-devel@xxxxxxxxxx > > > hda: packet command error: status=0x51 { DriveReady SeekComplete Error > > } > > > hda: packet command error: error=0x50 > > > ide: failed opcode was 100 > > > cdrom: open failed. > > > kjournald starting. Commit interval 5 seconds > > > EXT3-fs: mounted filesystem with ordered data mode. > > > security: 3 users, 4 roles, 355 types, 26 bools > > > security: 55 classes, 22610 rules > > > SELinux: Completing initialization. > > > SELinux: Setting up existing superblocks. > > > SELinux: initialized (dev dm-0, type ext3), uses xattr > > > SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs > > > SELinux: initialized (dev selinuxfs, type selinuxfs), uses > > genfs_contexts > > > SELinux: initialized (dev mqueue, type mqueue), not configured for > > labeling > > > SELinux: initialized (dev hugetlbfs, type hugetlbfs), uses > > genfs_contexts > > > SELinux: initialized (dev devpts, type devpts), uses transition SIDs > > > SELinux: initialized (dev eventpollfs, type eventpollfs), uses > > genfs_contexts > > > SELinux: initialized (dev pipefs, type pipefs), uses task SIDs > > > SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs > > > SELinux: initialized (dev futexfs, type futexfs), uses genfs_contexts > > > SELinux: initialized (dev sockfs, type sockfs), uses task SIDs > > > SELinux: initialized (dev proc, type proc), uses genfs_contexts > > > SELinux: initialized (dev bdev, type bdev), uses genfs_contexts > > > SELinux: initialized (dev rootfs, type rootfs), uses genfs_contexts > > > SELinux: initialized (dev sysfs, type sysfs), uses genfs_contexts > > > SELinux: initialized (dev usbfs, type usbfs), uses genfs_contexts > > > libata version 2.00 loaded. > > > Emulex LightPulse Fibre Channel SCSI driver 8.0.16.27 > > > Copyright(c) 2003-2006 Emulex. All rights reserved. > > > ACPI: PCI Interrupt 0000:06:02.0[A] -> GSI 78 (level, low) -> IRQ 225 > > > lpfc 0000:06:02.0: 0:1303 Link Up Event x1 received Data: x1 xf7 x8 x0 > > > scsi0 : Emulex LP9002L-F2 2Gb PCI Fibre Channel Adapter on PCI bus 06 > > device 10 irq 225 > > > ACPI: PCI Interrupt 0000:07:04.0[A] -> GSI 74 (level, low) -> IRQ 233 > > > lpfc 0000:07:04.0: 1:1303 Link Up Event x1 received Data: x1 xf7 x8 x0 > > > scsi1 : Emulex LP9002 2Gb PCI Fibre Channel Adapter on PCI bus 07 > > device 20 irq 233 > > > Vendor: HP Model: OPEN-E Rev: 2114 > > > Type: Direct-Access ANSI SCSI revision: 02 > > > SCSI device sda: 28452960 512-byte hdwr sectors (14568 MB) > > > SCSI device sda: drive cache: write back > > > SCSI device sda: 28452960 512-byte hdwr sectors (14568 MB) > > > SCSI device sda: drive cache: write back > > > sda: sda1 > > > Attached scsi disk sda at scsi1, channel 0, id 0, lun 0 > > > Vendor: HP Model: OPEN-E Rev: 2114 > > > Type: Direct-Access ANSI SCSI revision: 02 > > > SCSI device sdb: 28452960 512-byte hdwr sectors (14568 MB) > > > SCSI device sdb: drive cache: write back > > > SCSI device sdb: 28452960 512-byte hdwr sectors (14568 MB) > > > SCSI device sdb: drive cache: write back > > > sdb: unknown partition table > > > Attached scsi disk sdb at scsi1, channel 0, id 0, lun 1 > > > Vendor: HP Model: OPEN-E Rev: 2114 > > > Type: Direct-Access ANSI SCSI revision: 02 > > > SCSI device sdc: 28452960 512-byte hdwr sectors (14568 MB) > > > SCSI device sdc: drive cache: write back > > > SCSI device sdc: 28452960 512-byte hdwr sectors (14568 MB) > > > SCSI device sdc: drive cache: write back > > > sdc: unknown partition table > > > Attached scsi disk sdc at scsi1, channel 0, id 0, lun 2 > > > Vendor: HP Model: OPEN-E Rev: 2114 > > > Type: Direct-Access ANSI SCSI revision: 02 > > > SCSI device sdd: 28452960 512-byte hdwr sectors (14568 MB) > > > SCSI device sdd: drive cache: write back > > > SCSI device sdd: 28452960 512-byte hdwr sectors (14568 MB) > > > SCSI device sdd: drive cache: write back > > > sdd: unknown partition table > > > Attached scsi disk sdd at scsi1, channel 0, id 0, lun 3 > > > ACPI: PCI Interrupt 0000:07:05.0[A] -> GSI 73 (level, low) -> IRQ 50 > > > Losing some ticks... checking if CPU frequency changed. > > > lpfc 0000:07:05.0: 2:1303 Link Up Event x1 received Data: x1 xf7 x8 x0 > > > scsi2 : Emulex LP9002 2Gb PCI Fibre Channel Adapter on PCI bus 07 > > device 28 irq 50 > > > Vendor: HP Model: OPEN-E Rev: 2114 > > > Type: Direct-Access ANSI SCSI revision: 02 > > > SCSI device sde: 28452960 512-byte hdwr sectors (14568 MB) > > > SCSI device sde: drive cache: write back > > > SCSI device sde: 28452960 512-byte hdwr sectors (14568 MB) > > > SCSI device sde: drive cache: write back > > > sde: sde1 > > > Attached scsi disk sde at scsi2, channel 0, id 0, lun 0 > > > Vendor: HP Model: OPEN-E Rev: 2114 > > > Type: Direct-Access ANSI SCSI revision: 02 > > > SCSI device sdf: 28452960 512-byte hdwr sectors (14568 MB) > > > SCSI device sdf: drive cache: write back > > > SCSI device sdf: 28452960 512-byte hdwr sectors (14568 MB) > > > SCSI device sdf: drive cache: write back > > > sdf: unknown partition table > > > Attached scsi disk sdf at scsi2, channel 0, id 0, lun 1 > > > Vendor: HP Model: OPEN-E Rev: 2114 > > > Type: Direct-Access ANSI SCSI revision: 02 > > > SCSI device sdg: 28452960 512-byte hdwr sectors (14568 MB) > > > SCSI device sdg: drive cache: write back > > > SCSI device sdg: 28452960 512-byte hdwr sectors (14568 MB) > > > SCSI device sdg: drive cache: write back > > > sdg: unknown partition table > > > Attached scsi disk sdg at scsi2, channel 0, id 0, lun 2 > > > Vendor: HP Model: OPEN-E Rev: 2114 > > > Type: Direct-Access ANSI SCSI revision: 02 > > > SCSI device sdh: 28452960 512-byte hdwr sectors (14568 MB) > > > SCSI device sdh: drive cache: write back > > > SCSI device sdh: 28452960 512-byte hdwr sectors (14568 MB) > > > SCSI device sdh: drive cache: write back > > > sdh: unknown partition table > > > Attached scsi disk sdh at scsi2, channel 0, id 0, lun 3 > > > inserting floppy driver for 2.6.9-55.ELsmp > > > Floppy drive(s): fd0 is 1.44M > > > FDC 0 is a National Semiconductor PC87306 > > > Intel(R) PRO/1000 Network Driver - version 7.2.7-k2-NAPI > > > Copyright (c) 1999-2006 Intel Corporation. > > > ACPI: PCI Interrupt 0000:0a:01.0[A] -> GSI 97 (level, low) -> IRQ 58 > > > e1000: 0000:0a:01.0: e1000_probe: (PCI-X:133MHz:64-bit) > > 00:11:0a:64:7e:da > > > divert: allocating divert_blk for eth0 > > > e1000: eth0: e1000_probe: Intel(R) PRO/1000 Network Connection > > > ACPI: PCI Interrupt 0000:0a:01.1[B] -> GSI 98 (level, low) -> IRQ 66 > > > e1000: 0000:0a:01.1: e1000_probe: (PCI-X:133MHz:64-bit) > > 00:11:0a:64:7e:db > > > divert: allocating divert_blk for eth1 > > > e1000: eth1: e1000_probe: Intel(R) PRO/1000 Network Connection > > > tg3.c:v3.64-rh (July 31, 2006) > > > ACPI: PCI Interrupt 0000:03:01.0[A] -> GSI 25 (level, low) -> IRQ 201 > > > divert: allocating divert_blk for eth2 > > > eth2: Tigon3 [partno(N/A) rev 2100 PHY(5704)] (PCIX:133MHz:64-bit) > > 10/100/1000BaseT Ethernet 00:14:38:bf:5a:51 > > > eth2: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[1] Split[0] WireSpeed[1] > > TSOcap[0] > > > eth2: dma_rwctrl[769f4000] dma_mask[64-bit] > > > ACPI: PCI Interrupt 0000:03:01.1[B] -> GSI 26 (level, low) -> IRQ 209 > > > divert: allocating divert_blk for eth3 > > > eth3: Tigon3 [partno(N/A) rev 2100 PHY(5704)] (PCIX:133MHz:64-bit) > > 10/100/1000BaseT Ethernet 00:14:38:bf:5a:50 > > > eth3: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] Split[0] WireSpeed[1] > > TSOcap[1] > > > eth3: dma_rwctrl[769f4000] dma_mask[64-bit] > > > shpchp: acpi_shpchprm:\_SB_.PCI0 evaluate _BBN fail=0x5 > > > shpchp: acpi_shpchprm:get_device PCI ROOT HID fail=0x5 > > > shpchp: acpi_shpchprm:\_SB_.PCI0 evaluate _BBN fail=0x5 > > > shpchp: acpi_shpchprm:get_device PCI ROOT HID fail=0x5 > > > shpchp: acpi_shpchprm:\_SB_.PCI0 evaluate _BBN fail=0x5 > > > shpchp: acpi_shpchprm:get_device PCI ROOT HID fail=0x5 > > > shpchp: acpi_shpchprm:\_SB_.PCI0 evaluate _BBN fail=0x5 > > > shpchp: acpi_shpchprm:get_device PCI ROOT HID fail=0x5 > > > shpchp: acpi_shpchprm:\_SB_.PCI0 evaluate _BBN fail=0x5 > > > shpchp: acpi_shpchprm:get_device PCI ROOT HID fail=0x5 > > > hw_random hardware driver 1.0.0 loaded > > > shpchp: acpi_shpchprm:\_SB_.PCI0 evaluate _BBN fail=0x5 > > > shpchp: acpi_shpchprm:get_device PCI ROOT HID fail=0x5 > > > shpchp: acpi_shpchprm:\_SB_.PCI0 evaluate _BBN fail=0x5 > > > shpchp: acpi_shpchprm:get_device PCI ROOT HID fail=0x5 > > > ACPI: PCI Interrupt 0000:00:1d.7[D] -> GSI 23 (level, low) -> IRQ 193 > > > ehci_hcd 0000:00:1d.7: EHCI Host Controller > > > PCI: Setting latency timer of device 0000:00:1d.7 to 64 > > > ehci_hcd 0000:00:1d.7: irq 193, pci mem ffffff0010086000 > > > SELinux: initialized (dev usbdevfs, type usbdevfs), uses > > genfs_contexts > > > ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1 > > > PCI: cache line size of 128 is not supported by device 0000:00:1d.7 > > > ehci_hcd 0000:00:1d.7: USB 2.0 enabled, EHCI 1.00, driver 2004-May-10 > > > hub 1-0:1.0: USB hub found > > > hub 1-0:1.0: 8 ports detected > > > USB Universal Host Controller Interface driver v2.2 > > > ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 16 (level, low) -> IRQ 169 > > > uhci_hcd 0000:00:1d.0: UHCI Host Controller > > > PCI: Setting latency timer of device 0000:00:1d.0 to 64 > > > uhci_hcd 0000:00:1d.0: irq 169, io base 0000000000002000 > > > uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2 > > > hub 2-0:1.0: USB hub found > > > hub 2-0:1.0: 2 ports detected > > > ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 177 > > > uhci_hcd 0000:00:1d.1: UHCI Host Controller > > > PCI: Setting latency timer of device 0000:00:1d.1 to 64 > > > uhci_hcd 0000:00:1d.1: irq 177, io base 0000000000002020 > > > uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3 > > > hub 3-0:1.0: USB hub found > > > hub 3-0:1.0: 2 ports detected > > > ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 185 > > > uhci_hcd 0000:00:1d.2: UHCI Host Controller > > > PCI: Setting latency timer of device 0000:00:1d.2 to 64 > > > uhci_hcd 0000:00:1d.2: irq 185, io base 0000000000002040 > > > uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4 > > > hub 4-0:1.0: USB hub found > > > hub 4-0:1.0: 2 ports detected > > > ACPI: PCI Interrupt 0000:00:1d.3[A] -> GSI 16 (level, low) -> IRQ 169 > > > uhci_hcd 0000:00:1d.3: UHCI Host Controller > > > PCI: Setting latency timer of device 0000:00:1d.3 to 64 > > > uhci_hcd 0000:00:1d.3: irq 169, io base 0000000000002060 > > > uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 5 > > > hub 5-0:1.0: USB hub found > > > hub 5-0:1.0: 2 ports detected > > > md: Autodetecting RAID arrays. > > > md: autorun ... > > > md: ... autorun DONE. > > > ACPI: Power Button (FF) [PWRF] > > > EXT3 FS on dm-0, internal journal > > > device-mapper: dm-multipath version 1.0.5 loaded > > > device-mapper: dm-round-robin version 1.0.0 loaded > > > kjournald starting. Commit interval 5 seconds > > > EXT3 FS on cciss/c0d0p1, internal journal > > > EXT3-fs: mounted filesystem with ordered data mode. > > > SELinux: initialized (dev cciss/c0d0p1, type ext3), uses xattr > > > SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs > > > kjournald starting. Commit interval 5 seconds > > > EXT3 FS on dm-1, internal journal > > > EXT3-fs: mounted filesystem with ordered data mode. > > > SELinux: initialized (dev dm-1, type ext3), uses xattr > > > kjournald starting. Commit interval 5 seconds > > > EXT3 FS on dm-2, internal journal > > > EXT3-fs: mounted filesystem with ordered data mode. > > > SELinux: initialized (dev dm-2, type ext3), uses xattr > > > kjournald starting. Commit interval 5 seconds > > > EXT3 FS on dm-3, internal journal > > > EXT3-fs: mounted filesystem with ordered data mode. > > > SELinux: initialized (dev dm-3, type ext3), uses xattr > > > kjournald starting. Commit interval 5 seconds > > > EXT3 FS on dm-4, internal journal > > > EXT3-fs: mounted filesystem with ordered data mode. > > > SELinux: initialized (dev dm-4, type ext3), uses xattr > > > kjournald starting. Commit interval 5 seconds > > > EXT3 FS on dm-5, internal journal > > > EXT3-fs: mounted filesystem with ordered data mode. > > > SELinux: initialized (dev dm-5, type ext3), uses xattr > > > kjournald starting. Commit interval 5 seconds > > > EXT3 FS on dm-6, internal journal > > > EXT3-fs: mounted filesystem with ordered data mode. > > > SELinux: initialized (dev dm-6, type ext3), uses xattr > > > Adding 2097144k swap on /dev/vg00/swap1. Priority:-1 extents:1 > > > SELinux: initialized (dev binfmt_misc, type binfmt_misc), uses > > genfs_contexts > > > IA-32 Microcode Update Driver: v1.14 <tigran@xxxxxxxxxxx> > > > microcode: CPU0 already at revision 0x12 (current=0x12) > > > microcode: CPU1 already at revision 0x12 (current=0x12) > > > microcode: CPU2 already at revision 0x12 (current=0x12) > > > microcode: CPU3 already at revision 0x12 (current=0x12) > > > microcode: No new microdata for cpu 1 > > > microcode: No new microdata for cpu 2 > > > microcode: No new microdata for cpu 0 > > > microcode: No new microdata for cpu 3 > > > IA-32 Microcode Update Driver v1.14 unregistered > > > ip_tables: (C) 2000-2002 Netfilter core team > > > ip_conntrack version 2.1 (8192 buckets, 65536 max) - 456 bytes per > > conntrack > > > e1000: eth1: e1000_watchdog_task: NIC Link is Up 100 Mbps Half Duplex > > > i2c /dev entries driver > > > NET: Registered protocol family 10 > > > Disabled Privacy Extensions on device ffffffff80408540(lo) > > > IPv6 over IPv4 tunneling driver > > > divert: not allocating divert_blk for non-ethernet device sit0 > > > eth1: no IPv6 routers present > > > > > > > > > # cat /var/log/boot.log > > > Jan 31 15:02:31 corux38 syslog: syslogd startup succeeded > > > Jan 31 15:02:31 corux38 syslog: klogd startup succeeded > > > Jan 31 15:02:31 corux38 irqbalance: irqbalance startup succeeded > > > Jan 31 15:02:31 corux38 multipathd: multipathd startup succeeded > > > Jan 31 15:02:31 corux38 portmap: portmap startup succeeded > > > Jan 31 15:02:32 corux38 rc: Starting lm_sensors: succeeded > > > Jan 31 15:02:32 corux38 xinetd: xinetd startup succeeded > > > Jan 31 15:02:32 corux38 ntpd: ntpd startup succeeded > > > Jan 31 15:02:32 corux38 vsftpd: vsftpd vsftpd succeeded > > > Jan 31 15:02:33 corux38 ssh-server-g3: Starting ssh-server-g3 > > > Jan 31 10:01:59 corux38 rc.sysinit: -e > > > Jan 31 10:02:01 corux38 start_udev: Starting udev: succeeded > > > Jan 31 10:02:25 corux38 rc.sysinit: -e > > > Jan 31 10:02:25 corux38 sysctl: net.ipv4.ip_forward = 0 > > > Jan 31 10:02:25 corux38 sysctl: net.ipv4.conf.default.rp_filter = 1 > > > Jan 31 10:02:25 corux38 sysctl: > > net.ipv4.conf.default.accept_source_route = 0 > > > Jan 31 10:02:25 corux38 sysctl: kernel.sysrq = 0 > > > Jan 31 10:02:25 corux38 sysctl: kernel.core_uses_pid = 1 > > > Jan 31 10:02:25 corux38 sysctl: net.ipv4.conf.all.accept_source_route > > = 0 > > > Jan 31 10:02:25 corux38 sysctl: net.ipv4.tcp_max_syn_backlog = 4096 > > > Jan 31 10:02:25 corux38 sysctl: net.ipv4.conf.all.rp_filter = 1 > > > Jan 31 10:02:25 corux38 sysctl: net.ipv4.tcp_syncookies = 1 > > > Jan 31 10:02:25 corux38 sysctl: net.ipv4.conf.all.accept_redirects = 0 > > > Jan 31 10:02:25 corux38 sysctl: net.ipv4.conf.default.accept_redirects > > = 0 > > > Jan 31 10:02:25 corux38 sysctl: fs.file-max = 524288 > > > Jan 31 10:02:25 corux38 sysctl: kernel.sem = 1024 32000 32 4096 > > > Jan 31 10:02:25 corux38 rc.sysinit: Configuring kernel parameters: > > succeeded > > > Jan 31 15:02:26 corux38 date: Thu Jan 31 15:02:26 EST 2008 > > > Jan 31 15:02:26 corux38 rc.sysinit: Setting clock (localtime): Thu > > Jan 31 15:02:26 EST 2008 succeeded > > > Jan 31 15:02:26 corux38 rc.sysinit: Loading default keymap succeeded > > > Jan 31 15:02:26 corux38 rc.sysinit: Setting hostname corux38: > > succeeded > > > Jan 31 15:02:26 corux38 fsck: /dev/vg00/root: clean, 4335/131072 > > files, 48559/262144 blocks > > > Jan 31 15:02:26 corux38 rc.sysinit: Checking root filesystem succeeded > > > Jan 31 15:02:26 corux38 rc.sysinit: Remounting root filesystem in > > read-write mode: succeeded > > > Jan 31 15:02:26 corux38 lvm.static: 8 logical volume(s) in volume > > group vg00 now active > > > Jan 31 15:02:26 corux38 rc.sysinit: Setting up Logical Volume > > Management: succeeded > > > Jan 31 15:02:26 corux38 fsck: /boot: clean, 38/26104 files, > > 17822/104388 blocks > > > Jan 31 15:02:26 corux38 fsck: /dev/vg00/home: clean, 132/262144 files, > > 20580/524288 blocks > > > Jan 31 15:02:27 corux38 fsck: /dev/vg00/opt: clean, 83/524288 files, > > 36957/1048576 blocks > > > Jan 31 15:02:27 corux38 fsck: /dev/vg00/tmp: clean, 34/131072 files, > > 13541/262144 blocks > > > Jan 31 15:02:27 corux38 fsck: /dev/vg00/usr: clean, 30250/524288 > > files, 169645/1048576 blocks > > > Jan 31 15:02:27 corux38 fsck: /dev/vg00/usrlocal: clean, 46/270368 > > files, 17525/540672 blocks > > > Jan 31 15:02:27 corux38 fsck: /dev/vg00/var: clean, 395/1048576 files, > > 49124/2097152 blocks > > > Jan 31 15:02:27 corux38 rc.sysinit: Checking filesystems succeeded > > > Jan 31 15:02:27 corux38 rc.sysinit: Mounting local filesystems: > > succeeded > > > Jan 31 15:02:27 corux38 rc.sysinit: Enabling swap space: succeeded > > > Jan 31 15:02:28 corux38 microcode_ctl: microcode_ctl startup succeeded > > > Jan 31 15:02:36 corux38 ssh-server-g3: done. > > > Jan 31 15:02:28 corux38 vgchange: 8 logical volume(s) in volume > > group "vg00" monitored > > > Jan 31 15:02:36 corux38 rc: Starting ssh-server-g3: succeeded > > > Jan 31 15:02:28 corux38 lvm2-monitor: Starting monitoring for VG vg00: > > succeeded > > > Jan 31 15:02:36 corux38 crond: crond startup succeeded > > > Jan 31 15:02:28 corux38 cpuspeed: cpuspeed startup succeeded > > > Jan 31 15:02:28 corux38 iptables: succeeded > > > Jan 31 15:02:36 corux38 atd: atd startup succeeded > > > Jan 31 15:02:29 corux38 sysctl: net.ipv4.ip_forward = 0 > > > Jan 31 15:02:29 corux38 sysctl: net.ipv4.conf.default.rp_filter = 1 > > > Jan 31 15:02:36 corux38 messagebus: messagebus startup succeeded > > > Jan 31 15:02:29 corux38 sysctl: > > net.ipv4.conf.default.accept_source_route = 0 > > > Jan 31 15:02:29 corux38 sysctl: kernel.sysrq = 0 > > > Jan 31 15:02:29 corux38 sysctl: kernel.core_uses_pid = 1 > > > Jan 31 15:02:36 corux38 haldaemon: haldaemon startup succeeded > > > Jan 31 15:02:29 corux38 sysctl: net.ipv4.conf.all.accept_source_route > > = 0 > > > Jan 31 15:02:29 corux38 sysctl: net.ipv4.tcp_max_syn_backlog = 4096 > > > Jan 31 15:02:29 corux38 sysctl: net.ipv4.conf.all.rp_filter = 1 > > > Jan 31 15:02:29 corux38 sysctl: net.ipv4.tcp_syncookies = 1 > > > Jan 31 15:02:29 corux38 sysctl: net.ipv4.conf.all.accept_redirects = 0 > > > Jan 31 15:02:29 corux38 sysctl: net.ipv4.conf.default.accept_redirects > > = 0 > > > Jan 31 15:02:29 corux38 sysctl: fs.file-max = 524288 > > > Jan 31 15:02:29 corux38 sysctl: kernel.sem = 1024 32000 32 4096 > > > Jan 31 15:02:29 corux38 network: Setting network parameters: > > succeeded > > > Jan 31 15:02:29 corux38 network: Bringing up loopback interface: > > succeeded > > > Jan 31 15:02:31 corux38 network: Bringing up interface eth1: > > succeeded > > > Jan 31 15:03:08 corux38 haldaemon: haldaemon -TERM succeeded > > > Jan 31 15:03:08 corux38 messagebus: messagebus -TERM succeeded > > > Jan 31 15:03:08 corux38 atd: atd shutdown succeeded > > > Jan 31 15:03:09 corux38 vsftpd: vsftpd shutdown succeeded > > > Jan 31 15:03:09 corux38 xinetd: xinetd shutdown succeeded > > > Jan 31 15:03:09 corux38 crond: crond shutdown succeeded > > > Jan 31 15:03:09 corux38 ntpd: ntpd shutdown succeeded > > > Jan 31 15:03:09 corux38 irqbalance: irqbalance shutdown succeeded > > > Jan 31 15:03:09 corux38 multipathd: multipathd shutdown succeeded > > > Jan 31 15:03:09 corux38 portmap: portmap shutdown succeeded > > > Jan 31 15:05:36 corux38 syslog: syslogd startup succeeded > > > Jan 31 15:05:36 corux38 syslog: klogd startup succeeded > > > Jan 31 15:05:37 corux38 irqbalance: irqbalance startup succeeded > > > Jan 31 15:05:37 corux38 multipathd: multipathd startup succeeded > > > Jan 31 15:05:37 corux38 portmap: portmap startup succeeded > > > Jan 31 15:05:37 corux38 rc: Starting lm_sensors: succeeded > > > Jan 31 15:05:37 corux38 xinetd: xinetd startup succeeded > > > Jan 31 15:05:37 corux38 ntpd: ntpd startup succeeded > > > Jan 31 15:05:38 corux38 vsftpd: vsftpd vsftpd succeeded > > > Jan 31 15:05:38 corux38 ssh-server-g3: Starting ssh-server-g3 > > > Jan 31 10:05:03 corux38 rc.sysinit: -e > > > Jan 31 10:05:05 corux38 start_udev: Starting udev: succeeded > > > Jan 31 10:05:29 corux38 rc.sysinit: -e > > > Jan 31 10:05:29 corux38 sysctl: net.ipv4.ip_forward = 0 > > > Jan 31 10:05:29 corux38 sysctl: net.ipv4.conf.default.rp_filter = 1 > > > Jan 31 10:05:29 corux38 sysctl: > > net.ipv4.conf.default.accept_source_route = 0 > > > Jan 31 10:05:29 corux38 sysctl: kernel.sysrq = 0 > > > Jan 31 10:05:29 corux38 sysctl: kernel.core_uses_pid = 1 > > > Jan 31 10:05:29 corux38 sysctl: net.ipv4.conf.all.accept_source_route > > = 0 > > > Jan 31 10:05:29 corux38 sysctl: net.ipv4.tcp_max_syn_backlog = 4096 > > > Jan 31 10:05:29 corux38 sysctl: net.ipv4.conf.all.rp_filter = 1 > > > Jan 31 10:05:29 corux38 sysctl: net.ipv4.tcp_syncookies = 1 > > > Jan 31 10:05:29 corux38 sysctl: net.ipv4.conf.all.accept_redirects = 0 > > > Jan 31 10:05:29 corux38 sysctl: net.ipv4.conf.default.accept_redirects > > = 0 > > > Jan 31 10:05:29 corux38 sysctl: fs.file-max = 524288 > > > Jan 31 10:05:29 corux38 sysctl: kernel.sem = 1024 32000 32 4096 > > > Jan 31 10:05:29 corux38 rc.sysinit: Configuring kernel parameters: > > succeeded > > > Jan 31 15:05:30 corux38 date: Thu Jan 31 15:05:30 EST 2008 > > > Jan 31 15:05:30 corux38 rc.sysinit: Setting clock (localtime): Thu > > Jan 31 15:05:30 EST 2008 succeeded > > > Jan 31 15:05:30 corux38 rc.sysinit: Loading default keymap succeeded > > > Jan 31 15:05:30 corux38 rc.sysinit: Setting hostname corux38: > > succeeded > > > Jan 31 15:05:30 corux38 fsck: /dev/vg00/root: clean, 4335/131072 > > files, 48559/262144 blocks > > > Jan 31 15:05:30 corux38 rc.sysinit: Checking root filesystem succeeded > > > Jan 31 15:05:30 corux38 rc.sysinit: Remounting root filesystem in > > read-write mode: succeeded > > > Jan 31 15:05:30 corux38 lvm.static: 8 logical volume(s) in volume > > group vg00 now active > > > Jan 31 15:05:30 corux38 rc.sysinit: Setting up Logical Volume > > Management: succeeded > > > Jan 31 15:05:30 corux38 fsck: /boot: clean, 38/26104 files, > > 17822/104388 blocks > > > Jan 31 15:05:30 corux38 fsck: /dev/vg00/home: clean, 132/262144 files, > > 20580/524288 blocks > > > Jan 31 15:05:30 corux38 fsck: /dev/vg00/opt: clean, 83/524288 files, > > 36957/1048576 blocks > > > Jan 31 15:05:30 corux38 fsck: /dev/vg00/tmp: clean, 34/131072 files, > > 13541/262144 blocks > > > Jan 31 15:05:30 corux38 fsck: /dev/vg00/usr: clean, 30250/524288 > > files, 169645/1048576 blocks > > > Jan 31 15:05:30 corux38 fsck: /dev/vg00/usrlocal: clean, 46/270368 > > files, 17525/540672 blocks > > > Jan 31 15:05:31 corux38 fsck: /dev/vg00/var: clean, 395/1048576 files, > > 49141/2097152 blocks > > > Jan 31 15:05:31 corux38 rc.sysinit: Checking filesystems succeeded > > > Jan 31 15:05:31 corux38 rc.sysinit: Mounting local filesystems: > > succeeded > > > Jan 31 15:05:31 corux38 rc.sysinit: Enabling swap space: succeeded > > > Jan 31 15:05:32 corux38 microcode_ctl: microcode_ctl startup succeeded > > > Jan 31 15:05:32 corux38 vgchange: 8 logical volume(s) in volume > > group "vg00" monitored > > > Jan 31 15:05:32 corux38 lvm2-monitor: Starting monitoring for VG vg00: > > succeeded > > > Jan 31 15:05:41 corux38 ssh-server-g3: done. > > > Jan 31 15:05:32 corux38 cpuspeed: cpuspeed startup succeeded > > > Jan 31 15:05:41 corux38 rc: Starting ssh-server-g3: succeeded > > > Jan 31 15:05:32 corux38 iptables: succeeded > > > Jan 31 15:05:32 corux38 sysctl: net.ipv4.ip_forward = 0 > > > Jan 31 15:05:41 corux38 crond: crond startup succeeded > > > Jan 31 15:05:32 corux38 sysctl: net.ipv4.conf.default.rp_filter = 1 > > > Jan 31 15:05:41 corux38 atd: atd startup succeeded > > > Jan 31 15:05:32 corux38 sysctl: > > net.ipv4.conf.default.accept_source_route = 0 > > > Jan 31 15:05:32 corux38 sysctl: kernel.sysrq = 0 > > > Jan 31 15:05:32 corux38 sysctl: kernel.core_uses_pid = 1 > > > Jan 31 15:05:42 corux38 messagebus: messagebus startup succeeded > > > Jan 31 15:05:32 corux38 sysctl: net.ipv4.conf.all.accept_source_route > > = 0 > > > Jan 31 15:05:32 corux38 sysctl: net.ipv4.tcp_max_syn_backlog = 4096 > > > Jan 31 15:05:42 corux38 haldaemon: haldaemon startup succeeded > > > Jan 31 15:05:32 corux38 sysctl: net.ipv4.conf.all.rp_filter = 1 > > > Jan 31 15:05:32 corux38 sysctl: net.ipv4.tcp_syncookies = 1 > > > Jan 31 15:05:32 corux38 sysctl: net.ipv4.conf.all.accept_redirects = 0 > > > Jan 31 15:05:32 corux38 sysctl: net.ipv4.conf.default.accept_redirects > > = 0 > > > Jan 31 15:05:32 corux38 sysctl: fs.file-max = 524288 > > > Jan 31 15:05:32 corux38 sysctl: kernel.sem = 1024 32000 32 4096 > > > Jan 31 15:05:32 corux38 network: Setting network parameters: > > succeeded > > > Jan 31 15:05:32 corux38 network: Bringing up loopback interface: > > succeeded > > > Jan 31 15:05:36 corux38 network: Bringing up interface eth1: > > succeeded > > > > > > > > > # multipath -ll > > > mpath1 (00040026_05:84) > > > [size=13 GB][features="0"][hwhandler="0"] > > > \_ round-robin 0 [enabled] > > > \_ 2:0:0:1 sdf 8:80 [active][ready] > > > \_ 1:0:0:1 sdb 8:16 [active][ready] > > > > > > mpath0 (00040026_05:83) > > > [size=13 GB][features="0"][hwhandler="0"] > > > \_ round-robin 0 [enabled] > > > \_ 2:0:0:0 sde 8:64 [active][ready] > > > \_ 1:0:0:0 sda 8:0 [active][ready] > > Content-Description: manual_run.txt > > > > > -- > > > dm-devel mailing list > > > dm-devel@xxxxxxxxxx > > > https://www.redhat.com/mailman/listinfo/dm-devel > > > > -- > > dm-devel mailing list > > dm-devel@xxxxxxxxxx > > https://www.redhat.com/mailman/listinfo/dm-devel > > Content-Description: multipath_boot_log.txt > > %% > > %% running multipath from rc.sysinit > > %% > > load path identifiers cache > > ux_socket_connect error > > # > > # all paths in cache : > > # > > cciss!c0d0 blacklisted > > cciss!c0d1 blacklisted > > dm-0 blacklisted > > dm-1 blacklisted > > dm-2 blacklisted > > dm-3 blacklisted > > dm-4 blacklisted > > dm-5 blacklisted > > dm-6 blacklisted > > dm-7 blacklisted > > fd0 blacklisted > > hda blacklisted > > md0 blacklisted > > ram0 blacklisted > > ram10 blacklisted > > ram11 blacklisted > > ram12 blacklisted > > ram13 blacklisted > > ram14 blacklisted > > ram15 blacklisted > > ram1 blacklisted > > ram2 blacklisted > > ram3 blacklisted > > ram4 blacklisted > > ram5 blacklisted > > ram6 blacklisted > > ram7 blacklisted > > ram8 blacklisted > > ram9 blacklisted > > path sda not found in pathvec > > > > ===== path info sda (mask 0x1f) ===== > > bus = 1 > > dev_t = 8:0 > > size = 28452960 > > vendor = HP > > product = OPEN-E > > rev = 2114 > > h:b:t:l = 1:0:0:0 > > tgt_node_name = 0x50060e80039c5a04 > > serial = 40026 > > path checker = tur (controler setting) > > state = 2 > > getprio = /bin/true (internal default) > > prio = 0 > > getuid = /etc/xpdisk %n (controler setting) > > uid = 00040026_05:83 (callout) > > path sdb not found in pathvec > > > > ===== path info sdb (mask 0x1f) ===== > > bus = 1 > > dev_t = 8:16 > > size = 28452960 > > vendor = HP > > product = OPEN-E > > rev = 2114 > > h:b:t:l = 1:0:0:1 > > tgt_node_name = 0x50060e80039c5a04 > > serial = 40026 > > path checker = tur (controler setting) > > state = 2 > > getprio = /bin/true (internal default) > > prio = 0 > > getuid = /etc/xpdisk %n (controler setting) > > uid = 00040026_05:84 (callout) > > path sdc not found in pathvec > > > > ===== path info sdc (mask 0x1f) ===== > > bus = 1 > > dev_t = 8:32 > > size = 28452960 > > vendor = HP > > product = OPEN-E > > rev = 2114 > > h:b:t:l = 1:0:0:2 > > tgt_node_name = 0x50060e80039c5a04 > > serial = 40026 > > path checker = tur (controler setting) > > state = 2 > > getprio = /bin/true (internal default) > > prio = 0 > > getuid = /etc/xpdisk %n (controler setting) > > uid = 00040026_05:85 (callout) > > path sdd not found in pathvec > > > > ===== path info sdd (mask 0x1f) ===== > > bus = 1 > > dev_t = 8:48 > > size = 28452960 > > vendor = HP > > product = OPEN-E > > rev = 2114 > > h:b:t:l = 1:0:0:3 > > tgt_node_name = 0x50060e80039c5a04 > > serial = 40026 > > path checker = tur (controler setting) > > state = 2 > > getprio = /bin/true (internal default) > > prio = 0 > > getuid = /etc/xpdisk %n (controler setting) > > uid = 00040026_05:86 (callout) > > path sde not found in pathvec > > > > ===== path info sde (mask 0x1f) ===== > > bus = 1 > > dev_t = 8:64 > > size = 28452960 > > vendor = HP > > product = OPEN-E > > rev = 2114 > > h:b:t:l = 2:0:0:0 > > tgt_node_name = 0x50060e80039c5a14 > > path sdf not found in pathvec > > > > ===== path info sdf (mask 0x1f) ===== > > bus = 1 > > dev_t = 8:80 > > size = 28452960 > > vendor = HP > > product = OPEN-E > > rev = 2114 > > h:b:t:l = 2:0:0:1 > > tgt_node_name = 0x50060e80039c5a14 > > path sdg not found in pathvec > > > > ===== path info sdg (mask 0x1f) ===== > > bus = 1 > > dev_t = 8:96 > > size = 28452960 > > vendor = HP > > product = OPEN-E > > rev = 2114 > > h:b:t:l = 2:0:0:2 > > tgt_node_name = 0x50060e80039c5a14 > > path sdh not found in pathvec > > > > ===== path info sdh (mask 0x1f) ===== > > bus = 1 > > dev_t = 8:112 > > size = 28452960 > > vendor = HP > > product = OPEN-E > > rev = 2114 > > h:b:t:l = 2:0:0:3 > > tgt_node_name = 0x50060e80039c5a14 > > # > > # all paths : > > # > > 00040026_05:83 1:0:0:0 sda 8:0 [ready] HP /OPEN-E /2114 > > 00040026_05:84 1:0:0:1 sdb 8:16 [ready] HP /OPEN-E /2114 > > 00040026_05:85 1:0:0:2 sdc 8:32 [ready] HP /OPEN-E /2114 > > 00040026_05:86 1:0:0:3 sdd 8:48 [ready] HP /OPEN-E /2114 > > 2:0:0:0 sde 8:64 [faulty] HP /OPEN-E /2114 > > 2:0:0:1 sdf 8:80 [faulty] HP /OPEN-E /2114 > > 2:0:0:2 sdg 8:96 [faulty] HP /OPEN-E /2114 > > 2:0:0:3 sdh 8:112 [faulty] HP /OPEN-E /2114 > > Found matching wwid [00040026_05:83] in bindings file. > > Setting alias to mpath1 > > pgpolicy = multibus (controler setting) > > selector = round-robin 0 (internal default) > > features = 0 (internal default) > > hwhandler = 0 (internal default) > > rr_weight = 2 (config file default) > > rr_min_io = 100 (config file default) > > no_path_retry = -1 (config file default) > > pg_timeout = NONE (internal default) > > 0 28452960 multipath 0 0 1 1 round-robin 0 1 1 8:0 100 > > set ACT_CREATE: map does not exists > > message mpath1 0 switch_group 1 > > > > create: mpath1 (00040026_05:83) > > [size=13 GB][features="0"][hwhandler="0"] > > \_ round-robin 0 > > \_ 1:0:0:0 sda 8:0 [ready] > > > > reloading features > > Found matching wwid [00040026_05:84] in bindings file. > > Setting alias to mpath2 > > pgpolicy = multibus (controler setting) > > selector = round-robin 0 (internal default) > > features = 0 (internal default) > > hwhandler = 0 (internal default) > > rr_weight = 2 (config file default) > > rr_min_io = 100 (config file default) > > no_path_retry = -1 (config file default) > > pg_timeout = NONE (internal default) > > 0 28452960 multipath 0 0 1 1 round-robin 0 1 1 8:16 100 > > set ACT_CREATE: map does not exists > > message mpath2 0 switch_group 1 > > > > create: mpath2 (00040026_05:84) > > [size=13 GB][features="0"][hwhandler="0"] > > \_ round-robin 0 > > \_ 1:0:0:1 sdb 8:16 [ready] > > > > reloading features > > Found matching wwid [00040026_05:85] in bindings file. > > Setting alias to mpath3 > > pgpolicy = multibus (controler setting) > > selector = round-robin 0 (internal default) > > features = 0 (internal default) > > hwhandler = 0 (internal default) > > rr_weight = 2 (config file default) > > rr_min_io = 100 (config file default) > > no_path_retry = -1 (config file default) > > pg_timeout = NONE (internal default) > > 0 28452960 multipath 0 0 1 1 round-robin 0 1 1 8:32 100 > > set ACT_CREATE: map does not exists > > message mpath3 0 switch_group 1 > > > > create: mpath3 (00040026_05:85) > > [size=13 GB][features="0"][hwhandler="0"] > > \_ round-robin 0 > > \_ 1:0:0:2 sdc 8:32 [ready] > > > > reloading features > > Found matching wwid [00040026_05:86] in bindings file. > > Setting alias to mpath4 > > pgpolicy = multibus (controler setting) > > selector = round-robin 0 (internal default) > > features = 0 (internal default) > > hwhandler = 0 (internal default) > > rr_weight = 2 (config file default) > > rr_min_io = 100 (config file default) > > no_path_retry = -1 (config file default) > > pg_timeout = NONE (internal default) > > 0 28452960 multipath 0 0 1 1 round-robin 0 1 1 8:48 100 > > set ACT_CREATE: map does not exists > > message mpath4 0 switch_group 1 > > > > create: mpath4 (00040026_05:86) > > [size=13 GB][features="0"][hwhandler="0"] > > \_ round-robin 0 > > \_ 1:0:0:3 sdd 8:48 [ready] > > > > reloading features > > %% > > %% running multipath.dev > > %% > > add /block/sdh > > %% > > %% running multipath.dev > > %% > > add /block/md0 > > %% > > %% running multipath.dev > > %% > > add /block/sdg > > %% > > %% running multipath.dev > > %% > > add /block/sde > > %% > > %% running multipath.dev > > %% > > add /block/dm-8 > > %% > > %% running multipath.dev > > %% > > add /block/dm-9 > > %% > > %% running multipath.dev > > %% > > add /block/dm-10 > > %% > > %% running multipath.dev > > %% > > add /block/sdf > > %% > > %% running multipath.dev > > %% > > add /block/fd0 > > %% > > %% running multipath.dev > > %% > > add /block/dm-11 > > %% > > %% running multipath from rc.local > > %% > > create: mpath2 (00040026_05:85) > > [size=13 GB][features="0"][hwhandler="0"] > > \_ round-robin 0 > > \_ 1:0:0:2 sdc 8:32 [ready] > > \_ 2:0:0:2 sdg 8:96 [ready] > > > > %% > > %% running multipath.dev > > %% > > add /block/dm-10 > > > -- > > dm-devel mailing list > > dm-devel@xxxxxxxxxx > > https://www.redhat.com/mailman/listinfo/dm-devel > diff -urpN multipath-tools/libmultipath/discovery.c multipath-tools-patched/libmultipath/discovery.c > --- multipath-tools/libmultipath/discovery.c 2008-02-12 14:00:38.000000000 -0600 > +++ multipath-tools-patched/libmultipath/discovery.c 2008-02-15 09:28:32.000000000 -0600 > @@ -170,11 +170,6 @@ path_discovery (vector pathvec, struct c > return r; > } > > -/* > - * the daemon can race udev upon path add, > - * not multipath(8), ran by udev > - */ > -#if DAEMON > #define WAIT_MAX_SECONDS 5 > #define WAIT_LOOP_PER_SECOND 5 > > @@ -197,13 +192,6 @@ wait_for_file (char * filename) > } > return 1; > } > -#else > -static int > -wait_for_file (char * filename) > -{ > - return 0; > -} > -#endif > > #define declare_sysfs_get_str(fname, fmt) \ > extern int \ > -- > dm-devel mailing list > dm-devel@xxxxxxxxxx > https://www.redhat.com/mailman/listinfo/dm-devel -- dm-devel mailing list dm-devel@xxxxxxxxxx https://www.redhat.com/mailman/listinfo/dm-devel -- dm-devel mailing list dm-devel@xxxxxxxxxx https://www.redhat.com/mailman/listinfo/dm-devel
