Hi, I have a dual fabric / dual contoller setup which I've got partially to work with the multipath device mapper personality. I can create a multipath device and I can get multipathd to remove failed paths to the storage. However, once failed paths become active again, multipathd never adds the paths back into the devicemap. The multipath tools correctly identify the four paths to the storage and created the appropraite map. ia64g:~# multipath -v -d # all paths : 600508b40001045d0001c00006de0000 (2 0 0 1) /dev/sdc [HSV110 (C)COMPAQ] 600508b40001045d0001c00006de0000 (2 0 1 1) /dev/sdd [HSV110 (C)COMPAQ] 600508b40001045d0001c00006de0000 (3 0 0 1) /dev/sde [HSV110 (C)COMPAQ] 600508b40001045d0001c00006de0000 (3 0 1 1) /dev/sdf [HSV110 (C)COMPAQ] # all multipaths : 600508b40001045d0001c00006de0000 \_(2 0 0 1) /dev/sdc [HSV110 (C)COMPAQ] \_(2 0 1 1) /dev/sdd [HSV110 (C)COMPAQ] \_(3 0 0 1) /dev/sde [HSV110 (C)COMPAQ] \_(3 0 1 1) /dev/sdf [HSV110 (C)COMPAQ] ia64g:~# multipath U:600508b40001045d0001c00006de0000:0 209715200 multipath 2 round-robin 2 0 /dev/sdc /dev/sde round-robin 2 0 /dev/sdd /dev/sdf ia64g:~# dmsetup status 600508b40001045d0001c00006de0000: 0 209715200 multipath 2 2 0 8:32 A 1 8:64 A 1 2 0 8:48 A 1 8:80 A 1 I can format the multipath device and IO does indeed go down both SAN fabrics. If I pull one of the fabrics, multipathd correctly reconfigures the device, and IO continues down a single fabric. <syslog> May 28 15:16:46 ia64g kernel: qla2300 0000:40:01.1: LOOP DOWN detected. May 28 15:16:54 ia64g kernel: SCSI error : <3 0 0 1> return code = 0x10000 May 28 15:16:54 ia64g kernel: end_request: I/O error, dev sde, sector 33967656 May 28 15:15:33 ia64g /usr/bin/multipathd: [event thread] refresh failpaths list May 28 15:15:33 ia64g /usr/bin/multipathd: [event thread] start up event loops May 28 15:16:59 ia64g /usr/bin/multipathd: [checker thread] reconfigure 600508b40001045d0001c00006de ia64g:~# dmsetup status 600508b40001045d0001c00006de0000: 0 209715200 multipath 2 2 0 8:32 A 1 8:64 F 0 2 0 8:48 A 1 8:80 A 1 ia64g:~# multipath -d -v # all paths : 600508b40001045d0001c00006de0000 (2 0 0 1) /dev/sdc [HSV110 (C)COMPAQ] 600508b40001045d0001c00006de0000 (2 0 1 1) /dev/sdd [HSV110 (C)COMPAQ] 00000000000000000000000000000000 (3 0 0 1) /dev/sde [HSV110 (C)COMPAQ] 00000000000000000000000000000000 (3 0 1 1) /dev/sdf [HSV110 (C)COMPAQ] # all multipaths : 600508b40001045d0001c00006de0000 \_(2 0 0 1) /dev/sdc [HSV110 (C)COMPAQ] \_(2 0 1 1) /dev/sdd [HSV110 (C)COMPAQ] 00000000000000000000000000000000 \_(3 0 0 1) /dev/sde [HSV110 (C)COMPAQ] \_(3 0 1 1) /dev/sdf [HSV110 (C)COMPAQ] When I reconnect the seconds fabric, the newly active path does not get automatically added back into the device map. May 28 15:19:02 ia64g kernel: qla2300 0000:40:01.1: LIP reset occured (f7f7). May 28 15:19:02 ia64g kernel: qla2300 0000:40:01.1: LOOP UP detected (2 Gbps). ia64g:~# dmsetup status 600508b40001045d0001c00006de0000: 0 209715200 multipath 2 2 0 8:32 A 1 8:64 F 0 2 0 8:48 A 1 8:80 A 1 I can force a reconfiguration manually by issuing the "multipath" command again. ia64g:~# multipath U:600508b40001045d0001c00006de0000:0 209715200 multipath 2 round-robin 2 0 /dev/sdc /dev/sde round-robin 2 0 /dev/sdd /dev/sdf ia64g:~# dmsetup status 600508b40001045d0001c00006de0000: 0 209715200 multipath 2 2 0 8:32 A 1 8:64 A 1 2 0 8:48 A 1 8:80 A 1 Does anyone have any suggestions as to how to get multipathd to automatically act on the LOOP UP event? I running on kernel 2.6.6 on IA64 with 2.6.6-udm1 device mapper patchset with v0.2.0 of the multipath tools. The HBA is using QLogic Fibre Channel HBA Driver: 8.00.00b11-k and the storage targets are dual Compaq HSV110s. Cheers, Guy Coates -- Guy Coates, Informatics System Group The Wellcome Trust Sanger Institute, Hinxton, Cambridge, CB10 1SA, UK Tel: +44 (0)1223 834244 ex 7199