Hello Alim, On 10/21/2015 08:09 AM, Alim Akhtar wrote: [snip] >>>>> >>>>> Hi Alim, >>>>> >>>>> I have installed your patch set above with git am on top of >>>>> 4.3.0-rc6-00108-gce1fad2 torvalds/linux of today >>>>> with make exynos_defconfig on Odroid U3. >>>>> >>>> which exynos soc Odroid U3 uses? >>>> >>> OK, I can see its uses exynos4412 and exynos4412-odroidu3.dts does >>> include exynos4.dtsi, >>> so these should have worked. >>> >>>>> "halt -p" worked (power 0.0W). >>>>> "reboot" got stuck at 0.5W. >>>>> >>>> reboot stuck mean system does not reboot any more? >> >> It freezes when going for reboot. >> Have to power off/on to boot again. >> >> Btw I use an mmc, not an sd-card. >> No other HW connected, just LAN-cable. >> Bootloader is u-boot v2015.10. >> o > Have checked on 4.3.0-rc6-00006-gd03c139e7e77, still works on peach boards. > Sorry I don't have Odroid U3 with me, may be Javier or Krzysztof might help here to check whats wrong. To me its looks more of a board specific issue for now. > Krzysztof has an Odroid XU3 lite and I have an Odroid XU4, both uses an Exynos5422 so we can't check what's wrong with Odroid U3 (Exynos4412). Having said that I think I know what is the issue here. Markus said that he is using an eMMC instead of an uSD (which is what I used and my guess is that Krzysztof did too). Now, there is a subtle difference between the old PMU restart handler and the syscon-reboot one, and that is the restart handler priorities: notifier priority ------------------------------------ pmu_restart_notify 128 mmc_pwrseq_emmc_reset_nb 129 syscon_restart_handle 192 So, without Alim's patches, first the eMMC reset handler will be called and then the PMU restart handler but after his series, the syscon reset handler has a higher priority so the eMMC reset will never be called. But the problem is that the eMMC card has to be properly reset on system restart to allow the SoC iROM to be able to read the bootloader from the eMMC since the iROM doesn't have restart logic and the card shouldn't be left in an unknown state. So the problem here is not that the system is not being reset (that I think that works) but that on reboot, the system is not able to boot again since the ROM is not able to read the second stage bootloader. Markus, Can you please test following patch [0] on top of Alim's series? If that works then it should either be part of Alim's series or the patches will have to wait until that patch lands into mainline. I don't have an eMMC to test it in XU4 but I'm pretty confident that it will solve the issue. Best regards, -- Javier Martinez Canillas Open Source Group Samsung Research America [0]: >From c9b250ee03bae338339b70693e906145c719f783 Mon Sep 17 00:00:00 2001 From: Javier Martinez Canillas <javier@xxxxxxxxxxxxxxx> Date: Wed, 21 Oct 2015 11:59:44 +0200 Subject: [RFT PATCH] mmc: pwrseq: Use highest priority for eMMC restart handler The pwrseq_emmc driver does a eMMC card reset before a system reboot to allow broken or limited ROM boot-loaders, that don't have an eMMC reset logic, to be able to read the second stage from the eMMC. But this has to be called before a system reboot handler and while most of them use the priority 128, there are other restart handlers (such as the syscon-reboot one) that use a higher priority. So, use the highest priority to make sure that the eMMC hw is reset before a system reboot. Signed-off-by: Javier Martinez Canillas <javier@xxxxxxxxxxxxxxx> --- drivers/mmc/core/pwrseq_emmc.c | 6 +++--- 1 file changed, 3 insertions(+), 3 deletions(-) diff --git a/drivers/mmc/core/pwrseq_emmc.c b/drivers/mmc/core/pwrseq_emmc.c index 137c97fb7aa8..ad4f94ec7e8d 100644 --- a/drivers/mmc/core/pwrseq_emmc.c +++ b/drivers/mmc/core/pwrseq_emmc.c @@ -84,11 +84,11 @@ struct mmc_pwrseq *mmc_pwrseq_emmc_alloc(struct mmc_host *host, /* * register reset handler to ensure emmc reset also from - * emergency_reboot(), priority 129 schedules it just before - * system reboot + * emergency_reboot(), priority 255 is the highest priority + * so it will be executed before any system reboot handler. */ pwrseq->reset_nb.notifier_call = mmc_pwrseq_emmc_reset_nb; - pwrseq->reset_nb.priority = 129; + pwrseq->reset_nb.priority = 255; register_restart_handler(&pwrseq->reset_nb); pwrseq->pwrseq.ops = &mmc_pwrseq_emmc_ops; -- 2.4.3 -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
