Remove gpio to pinctrl pin mapping code from driver and address this through standard property "gpio-ranges". Signed-off-by: Pramod Kumar <pramodku@xxxxxxxxxxxx> Reviewed-by: Ray Jui <rjui@xxxxxxxxxxxx> Reviewed-by: Scott Branden <sbranden@xxxxxxxxxxxx> --- drivers/pinctrl/bcm/pinctrl-cygnus-gpio.c | 131 +----------------------------- 1 file changed, 3 insertions(+), 128 deletions(-) diff --git a/drivers/pinctrl/bcm/pinctrl-cygnus-gpio.c b/drivers/pinctrl/bcm/pinctrl-cygnus-gpio.c index 1ca7830..12a48f4 100644 --- a/drivers/pinctrl/bcm/pinctrl-cygnus-gpio.c +++ b/drivers/pinctrl/bcm/pinctrl-cygnus-gpio.c @@ -29,7 +29,6 @@ #include <linux/of_device.h> #include <linux/of_irq.h> #include <linux/pinctrl/pinctrl.h> -#include <linux/pinctrl/pinmux.h> #include <linux/pinctrl/pinconf.h> #include <linux/pinctrl/pinconf-generic.h> @@ -597,127 +596,6 @@ static const struct pinconf_ops cygnus_pconf_ops = { }; /* - * Map a GPIO in the local gpio_chip pin space to a pin in the Cygnus IOMUX - * pinctrl pin space - */ -struct cygnus_gpio_pin_range { - unsigned offset; - unsigned pin_base; - unsigned num_pins; -}; - -#define CYGNUS_PINRANGE(o, p, n) { .offset = o, .pin_base = p, .num_pins = n } - -/* - * Pin mapping table for mapping local GPIO pins to Cygnus IOMUX pinctrl pins - */ -static const struct cygnus_gpio_pin_range cygnus_gpio_pintable[] = { - CYGNUS_PINRANGE(0, 42, 1), - CYGNUS_PINRANGE(1, 44, 3), - CYGNUS_PINRANGE(4, 48, 1), - CYGNUS_PINRANGE(5, 50, 3), - CYGNUS_PINRANGE(8, 126, 1), - CYGNUS_PINRANGE(9, 155, 1), - CYGNUS_PINRANGE(10, 152, 1), - CYGNUS_PINRANGE(11, 154, 1), - CYGNUS_PINRANGE(12, 153, 1), - CYGNUS_PINRANGE(13, 127, 3), - CYGNUS_PINRANGE(16, 140, 1), - CYGNUS_PINRANGE(17, 145, 7), - CYGNUS_PINRANGE(24, 130, 10), - CYGNUS_PINRANGE(34, 141, 4), - CYGNUS_PINRANGE(38, 54, 1), - CYGNUS_PINRANGE(39, 56, 3), - CYGNUS_PINRANGE(42, 60, 3), - CYGNUS_PINRANGE(45, 64, 3), - CYGNUS_PINRANGE(48, 68, 2), - CYGNUS_PINRANGE(50, 84, 6), - CYGNUS_PINRANGE(56, 94, 6), - CYGNUS_PINRANGE(62, 72, 1), - CYGNUS_PINRANGE(63, 70, 1), - CYGNUS_PINRANGE(64, 80, 1), - CYGNUS_PINRANGE(65, 74, 3), - CYGNUS_PINRANGE(68, 78, 1), - CYGNUS_PINRANGE(69, 82, 1), - CYGNUS_PINRANGE(70, 156, 17), - CYGNUS_PINRANGE(87, 104, 12), - CYGNUS_PINRANGE(99, 102, 2), - CYGNUS_PINRANGE(101, 90, 4), - CYGNUS_PINRANGE(105, 116, 6), - CYGNUS_PINRANGE(111, 100, 2), - CYGNUS_PINRANGE(113, 122, 4), - CYGNUS_PINRANGE(123, 11, 1), - CYGNUS_PINRANGE(124, 38, 4), - CYGNUS_PINRANGE(128, 43, 1), - CYGNUS_PINRANGE(129, 47, 1), - CYGNUS_PINRANGE(130, 49, 1), - CYGNUS_PINRANGE(131, 53, 1), - CYGNUS_PINRANGE(132, 55, 1), - CYGNUS_PINRANGE(133, 59, 1), - CYGNUS_PINRANGE(134, 63, 1), - CYGNUS_PINRANGE(135, 67, 1), - CYGNUS_PINRANGE(136, 71, 1), - CYGNUS_PINRANGE(137, 73, 1), - CYGNUS_PINRANGE(138, 77, 1), - CYGNUS_PINRANGE(139, 79, 1), - CYGNUS_PINRANGE(140, 81, 1), - CYGNUS_PINRANGE(141, 83, 1), - CYGNUS_PINRANGE(142, 10, 1) -}; - -/* - * The Cygnus IOMUX controller mainly supports group based mux configuration, - * but certain pins can be muxed to GPIO individually. Only the ASIU GPIO - * controller can support this, so it's an optional configuration - * - * Return -ENODEV means no support and that's fine - */ -static int cygnus_gpio_pinmux_add_range(struct cygnus_gpio *chip) -{ - struct device_node *node = chip->dev->of_node; - struct device_node *pinmux_node; - struct platform_device *pinmux_pdev; - struct gpio_chip *gc = &chip->gc; - int i, ret = 0; - - /* parse DT to find the phandle to the pinmux controller */ - pinmux_node = of_parse_phandle(node, "pinmux", 0); - if (!pinmux_node) - return -ENODEV; - - pinmux_pdev = of_find_device_by_node(pinmux_node); - /* no longer need the pinmux node */ - of_node_put(pinmux_node); - if (!pinmux_pdev) { - dev_err(chip->dev, "failed to get pinmux device\n"); - return -EINVAL; - } - - /* now need to create the mapping between local GPIO and PINMUX pins */ - for (i = 0; i < ARRAY_SIZE(cygnus_gpio_pintable); i++) { - ret = gpiochip_add_pin_range(gc, dev_name(&pinmux_pdev->dev), - cygnus_gpio_pintable[i].offset, - cygnus_gpio_pintable[i].pin_base, - cygnus_gpio_pintable[i].num_pins); - if (ret) { - dev_err(chip->dev, "unable to add GPIO pin range\n"); - goto err_put_device; - } - } - - chip->pinmux_is_supported = true; - - /* no need for pinmux_pdev device reference anymore */ - put_device(&pinmux_pdev->dev); - return 0; - -err_put_device: - put_device(&pinmux_pdev->dev); - gpiochip_remove_pin_ranges(gc); - return ret; -} - -/* * Cygnus GPIO controller supports some PINCONF related configurations such as * pull up, pull down, and drive strength, when the pin is configured to GPIO * @@ -851,18 +729,15 @@ static int cygnus_gpio_probe(struct platform_device *pdev) gc->set = cygnus_gpio_set; gc->get = cygnus_gpio_get; + chip->pinmux_is_supported = of_property_read_bool(dev->of_node, + "gpio-ranges"); + ret = gpiochip_add(gc); if (ret < 0) { dev_err(dev, "unable to add GPIO chip\n"); return ret; } - ret = cygnus_gpio_pinmux_add_range(chip); - if (ret && ret != -ENODEV) { - dev_err(dev, "unable to add GPIO pin range\n"); - goto err_rm_gpiochip; - } - ret = cygnus_gpio_register_pinconf(chip); if (ret) { dev_err(dev, "unable to register pinconf\n"); -- 1.9.1 -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html