Rename gpio driver file name from pinctrl-cygnus-gpio.c to
pinctrl-iproc-gpio.c to make it more generic so that all
iproc based future SoCs using the same gpio block could
use this driver.
Signed-off-by: Pramod Kumar <pramodku@xxxxxxxxxxxx>
Reviewed-by: Ray Jui <rjui@xxxxxxxxxxxx>
Reviewed-by: Scott Branden <sbranden@xxxxxxxxxxxx>
---
drivers/pinctrl/bcm/Kconfig | 30 ++++++++++++++++------
drivers/pinctrl/bcm/Makefile | 2 +-
...{pinctrl-cygnus-gpio.c => pinctrl-iproc-gpio.c} | 3 +--
3 files changed, 24 insertions(+), 11 deletions(-)
rename drivers/pinctrl/bcm/{pinctrl-cygnus-gpio.c => pinctrl-iproc-gpio.c} (99%)
diff --git a/drivers/pinctrl/bcm/Kconfig b/drivers/pinctrl/bcm/Kconfig
index cd11d4d..5949547 100644
--- a/drivers/pinctrl/bcm/Kconfig
+++ b/drivers/pinctrl/bcm/Kconfig
@@ -20,27 +20,41 @@ config PINCTRL_BCM2835
select PINMUX
select PINCONF
-config PINCTRL_CYGNUS_GPIO
- bool "Broadcom Cygnus GPIO (with PINCONF) driver"
- depends on OF_GPIO && ARCH_BCM_CYGNUS
+config PINCTRL_IPROC_GPIO
+ bool "Broadcom iProc GPIO (with PINCONF) driver"
+ depends on OF_GPIO && (ARCH_BCM_IPROC || COMPILE_TEST)
select GPIOLIB_IRQCHIP
select PINCONF
select GENERIC_PINCONF
- default ARCH_BCM_CYGNUS
+ default ARCH_BCM_IPROC
help
- Say yes here to enable the Broadcom Cygnus GPIO driver.
+ Say yes here to enable the Broadcom iProc GPIO driver.
+
+ The Broadcom iProc based SoCs- Cygnus, NS2, NSP and Stingray, use
+ same GPIO Controller IP hence this driver could be used for all.
The Broadcom Cygnus SoC has 3 GPIO controllers including the ASIU
GPIO controller (ASIU), the chipCommonG GPIO controller (CCM), and
the always-ON GPIO controller (CRMU/AON). All 3 GPIO controllers are
supported by this driver.
- All 3 Cygnus GPIO controllers support basic PINCONF functions such
+ The Broadcom NSP has two GPIO controllers including the ChipcommonA
+ GPIO, the ChipcommonB GPIO. Later controller is supported by this
+ driver.
+
+ The Broadcom NS2 has two GPIO controller including the CRMU GPIO,
+ the ChipcommonG GPIO. Both controllers are supported by this driver.
+
+ The Broadcom Stingray GPIO controllers are supported by this driver.
+
+ All above SoCs GPIO controllers support basic PINCONF functions such
as bias pull up, pull down, and drive strength configurations, when
these pins are muxed to GPIO.
- Pins from the ASIU GPIO can be individually muxed to GPIO function,
- through interaction with the Cygnus IOMUX controller.
+ It provides the framework where pins from the individual GPIO can be
+ individually muxed to GPIO function, through interaction with the
+ SoCs IOMUX controller. This features could be used only on SoCs which
+ support individual pin muxing.
config PINCTRL_CYGNUS_MUX
bool "Broadcom Cygnus IOMUX driver"
diff --git a/drivers/pinctrl/bcm/Makefile b/drivers/pinctrl/bcm/Makefile
index 2b2f70e..9ac6370 100644
--- a/drivers/pinctrl/bcm/Makefile
+++ b/drivers/pinctrl/bcm/Makefile
@@ -2,5 +2,5 @@
obj-$(CONFIG_PINCTRL_BCM281XX) += pinctrl-bcm281xx.o
obj-$(CONFIG_PINCTRL_BCM2835) += pinctrl-bcm2835.o
-obj-$(CONFIG_PINCTRL_CYGNUS_GPIO) += pinctrl-cygnus-gpio.o
+obj-$(CONFIG_PINCTRL_IPROC_GPIO) += pinctrl-iproc-gpio.o
obj-$(CONFIG_PINCTRL_CYGNUS_MUX) += pinctrl-cygnus-mux.o
diff --git a/drivers/pinctrl/bcm/pinctrl-cygnus-gpio.c b/drivers/pinctrl/bcm/pinctrl-iproc-gpio.c
similarity index 99%
rename from drivers/pinctrl/bcm/pinctrl-cygnus-gpio.c
rename to drivers/pinctrl/bcm/pinctrl-iproc-gpio.c
index ed21ab2..de09859 100644
--- a/drivers/pinctrl/bcm/pinctrl-cygnus-gpio.c
+++ b/drivers/pinctrl/bcm/pinctrl-iproc-gpio.c
@@ -531,8 +531,7 @@ static int iproc_pin_config_get(struct pinctrl_dev *pctldev, unsigned pin,
ret = iproc_gpio_get_strength(chip, gpio, &arg);
if (ret)
return ret;
- else
- *config = pinconf_to_config_packed(param, arg);
+ *config = pinconf_to_config_packed(param, arg);
return 0;
--
1.9.1
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
