This change is important in order for everyone to be easily able to use the
driver for one of the supported accelerometer chips!
Until now, the driver blindly assumed that the INT1 interrupt line is wired
on a user's board. But these devices have 2 interrupt lines and can route
their interrupt sources to one of them. Now, if "INT2" is found and matches
i2c_client->irq, INT2 will be used.
The chip's default actually is INT2, which is why probably many boards will
have it wired and can make use of this.
Of course, this also falls back to assuming INT1, so for existing users
nothing will break. The new functionality is described in the bindings doc.
Signed-off-by: Martin Kepplinger <martin.kepplinger@xxxxxxxxxxxxxxxxxxxxx>
---
changelog:
v4: use irq that matches client->irq, backwards compatible
v3: correctly assign irq if both pins are described in DT
v2: don't warn but normally handle if both pins are described in dts
thanks Mark Rutland
v1: initial post
.../devicetree/bindings/iio/accel/mma8452.txt | 6 ++++++
drivers/iio/accel/mma8452.c | 21 +++++++++++++++------
2 files changed, 21 insertions(+), 6 deletions(-)
diff --git a/Documentation/devicetree/bindings/iio/accel/mma8452.txt b/Documentation/devicetree/bindings/iio/accel/mma8452.txt
index e3c3746..3c10e85 100644
--- a/Documentation/devicetree/bindings/iio/accel/mma8452.txt
+++ b/Documentation/devicetree/bindings/iio/accel/mma8452.txt
@@ -7,13 +7,18 @@ Required properties:
* "fsl,mma8453"
* "fsl,mma8652"
* "fsl,mma8653"
+
- reg: the I2C address of the chip
Optional properties:
- interrupt-parent: should be the phandle for the interrupt controller
+
- interrupts: interrupt mapping for GPIO IRQ
+ - interrupt-names: should contain "INT1" and/or "INT2", the accelerometer's
+ interrupt line in use.
+
Example:
mma8453fc@1d {
@@ -21,4 +26,5 @@ Example:
reg = <0x1d>;
interrupt-parent = <&gpio1>;
interrupts = <5 0>;
+ interrupt-names = "INT2";
};
diff --git a/drivers/iio/accel/mma8452.c b/drivers/iio/accel/mma8452.c
index 1eccc2d..116a6e4 100644
--- a/drivers/iio/accel/mma8452.c
+++ b/drivers/iio/accel/mma8452.c
@@ -29,6 +29,7 @@
#include <linux/iio/events.h>
#include <linux/delay.h>
#include <linux/of_device.h>
+#include <linux/of_irq.h>
#define MMA8452_STATUS 0x00
#define MMA8452_STATUS_DRDY (BIT(2) | BIT(1) | BIT(0))
@@ -1130,13 +1131,21 @@ static int mma8452_probe(struct i2c_client *client,
MMA8452_INT_FF_MT;
int enabled_interrupts = MMA8452_INT_TRANS |
MMA8452_INT_FF_MT;
+ int irq2;
- /* Assume wired to INT1 pin */
- ret = i2c_smbus_write_byte_data(client,
- MMA8452_CTRL_REG5,
- supported_interrupts);
- if (ret < 0)
- return ret;
+ irq2 = of_irq_get_byname(client->dev.of_node, "INT2");
+
+ if (irq2 == client->irq) {
+ dev_dbg(&client->dev, "using interrupt line INT2\n");
+ } else {
+ ret = i2c_smbus_write_byte_data(client,
+ MMA8452_CTRL_REG5,
+ supported_interrupts);
+ if (ret < 0)
+ return ret;
+
+ dev_dbg(&client->dev, "using interrupt line INT1\n");
+ }
ret = i2c_smbus_write_byte_data(client,
MMA8452_CTRL_REG4,
--
2.1.4
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
