> -----Original Message-----
> From: Karicheri, Muralidharan
> Sent: Tuesday, October 13, 2015 2:24 PM
> To: Kwok, WingMan; robh+dt@xxxxxxxxxx; pawel.moll@xxxxxxx;
> mark.rutland@xxxxxxx; ijc+devicetree@xxxxxxxxxxxxxx; galak@xxxxxxxxxxxxxx;
> KISHON VIJAY ABRAHAM; Quadros, Roger; bhelgaas@xxxxxxxxxx;
> ssantosh@xxxxxxxxxx; linux@xxxxxxxxxxxxxxxx; devicetree@xxxxxxxxxxxxxxx;
> linux-kernel@xxxxxxxxxxxxxxx; linux-pci@xxxxxxxxxxxxxxx; linux-arm-
> kernel@xxxxxxxxxxxxxxxxxxx
> Subject: Re: [PATCH 3/3] ARM: keystone: dts: add PCI serdes driver bindings
>
> On 10/13/2015 02:04 PM, WingMan Kwok wrote:
> > Signed-off-by: WingMan Kwok <w-kwok2@xxxxxx>
> > ---
> > arch/arm/boot/dts/k2e.dtsi | 24 ++++++++++++++++++++++++
> > arch/arm/boot/dts/keystone.dtsi | 25 +++++++++++++++++++++++++
> > 2 files changed, 49 insertions(+)
> >
> > diff --git a/arch/arm/boot/dts/k2e.dtsi b/arch/arm/boot/dts/k2e.dtsi
> > index 675fb8e..1ba47d8 100644
> > --- a/arch/arm/boot/dts/k2e.dtsi
> > +++ b/arch/arm/boot/dts/k2e.dtsi
> > @@ -86,6 +86,18 @@
> > gpio,syscon-dev = <&devctrl 0x240>;
> > };
> >
> > + pcie1_phy: pciephy@2326000 {
> > + #phy-cells = <0>;
> > + compatible = "ti,keystone-serdes-pcie";
> > + reg = <0x02326000 0x4000>;
> > + reg-names = "reg_serdes";
> > + refclk-khz = <100000>;
> > + link-rate-kbps = <5000000>;
> > + phy-type = "pcie";
> > + max-lanes = <2>;
> > + status = "disabled";
> > + };
> > +
> > pcie1: pcie@21020000 {
> > compatible = "ti,keystone-pcie","snps,dw-pcie";
> > clocks = <&clkpcie1>;
> > @@ -130,6 +142,18 @@
> > <GIC_SPI 375 IRQ_TYPE_EDGE_RISING>,
> > <GIC_SPI 376 IRQ_TYPE_EDGE_RISING>;
> > };
> > +
> > + /* PCIE phy */
> > + serdeses {
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > + serdes@0 {
> > + reg = <0>;
> > + phys = <&pcie1_phy>;
> > + status = "disabled";
> > + };
> > + };
> > +
> > };
> >
> > mdio: mdio@24200f00 {
> > diff --git a/arch/arm/boot/dts/keystone.dtsi
> b/arch/arm/boot/dts/keystone.dtsi
> > index 72816d6..5312319 100644
> > --- a/arch/arm/boot/dts/keystone.dtsi
> > +++ b/arch/arm/boot/dts/keystone.dtsi
> > @@ -275,6 +275,19 @@
> > ti,syscon-dev = <&devctrl 0x2a0>;
> > };
> >
> > + pcie0_phy: pciephy@2320000 {
> > + #phy-cells = <0>;
> > + compatible = "ti,keystone-serdes-pcie";
> > + reg = <0x02320000 0x4000>;
> > + reg-names = "reg_serdes";
> > + refclk-khz = <100000>;
> > + link-rate-kbps = <5000000>;
> > + init-firmware = "k2_pcie_serdes_init.fw";
> > + phy-type = "pcie";
> > + max-lanes = <2>;
> > + status = "disabled";
> > + };
> > +
> > pcie0: pcie@21800000 {
> > compatible = "ti,keystone-pcie", "snps,dw-pcie";
> > clocks = <&clkpcie>;
> > @@ -319,6 +332,18 @@
> > <GIC_SPI 28 IRQ_TYPE_EDGE_RISING>,
> > <GIC_SPI 29 IRQ_TYPE_EDGE_RISING>;
> > };
> > +
> > + /* PCIE phy */
> > + serdeses {
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > + serdes@0 {
> > + reg = <0>;
> > + phys = <&pcie0_phy>;
> > + status = "disabled";
> > + };
> > + };
> > +
> > };
> > };
> > };
> >
> Wingman,
>
> This should be a separate patch and remove the sane from Driver patch.
> i.e. send 1/3 ane 2/3 in one series and 3/3 as a separate patch.
>
will do.
Thanks,
wingMan
��.n��������+%������w��{.n����z�{��ܨ}���Ơz�j:+v�����w����ޙ��&�)ߡ�a����z�ޗ���ݢj��w�f
