[PATCH 2/3] ARM: dts: sun4i: Enable USB DRC on pcDuino1/2

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 




Enable the otg/drc usb controller on the pcDuino1/2 board. Note
that the pcDuino2 FEX file from the vendor contains the following
information:

    [usbc0]
    usb_used = 1
    usb_port_type = 0
    usb_detect_type = 1
    usb_id_gpio = port:PH04<0><1><default><default>
    usb_det_vbus_gpio = port:PH05<0><0><default><default>
    usb_drv_vbus_gpio = port:PD02<1><0><default><0>
    usb_host_init_state = 0

The ID pin is indeed PH4. The PD2 pin can be used to switch power
on/off for the USB Type A receptacle, but it has nothing to do with
the MicroUSB OTG receptacle. The VBUS pin of the MicroUSB receptacle
is always connected to 5V according to the schematics and confirmed
by doing some tests with the device. The PH5 pin is just one of the
pins on the J8 expansion header and has nothing to do with USB OTG.
There is also the PB9 pin labelled as USB0-DRV on the schematics.
This PB9 pin is pulled up and connected to the N_VBUSEN pin of AXP209
PMIC, while the VBUS pin of AXP209 only has a capacitor between it
and the ground (this pin is not used for anything else).

To sum it up. Only the ID pin (PH4) works as expected. And 5V voltage
is always served to the MicroUSB OTG receptacle no matter what is the
state of the PB9/PD2 pins.

This patch has been tested to work fine in a host role with a USB
keyboard connected via an OTG cable. It also works fine in a device
role (cdc_ether) with a regular Micro-B cable connected to a desktop
PC.

Signed-off-by: Siarhei Siamashka <siarhei.siamashka@xxxxxxxxx>
---
 arch/arm/boot/dts/sun4i-a10-pcduino.dts | 19 +++++++++++++++++++
 1 file changed, 19 insertions(+)

diff --git a/arch/arm/boot/dts/sun4i-a10-pcduino.dts b/arch/arm/boot/dts/sun4i-a10-pcduino.dts
index fdc074c..c9b9330 100644
--- a/arch/arm/boot/dts/sun4i-a10-pcduino.dts
+++ b/arch/arm/boot/dts/sun4i-a10-pcduino.dts
@@ -164,6 +164,10 @@
 	status = "okay";
 };
 
+&otg_sram {
+	status = "okay";
+};
+
 &pio {
 	led_pins_pcduino: led_pins@0 {
 		allwinner,pins = "PH15", "PH16";
@@ -178,6 +182,13 @@
 		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
 		allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
 	};
+
+	usb0_id_detect_pin: usb0_id_detect_pin@0 {
+		allwinner,pins = "PH4";
+		allwinner,function = "gpio_in";
+		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+		allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+	};
 };
 
 &uart0 {
@@ -186,6 +197,14 @@
 	status = "okay";
 };
 
+&usb_otg {
+	dr_mode = "otg";
+	status = "okay";
+};
+
 &usbphy {
+	pinctrl-names = "default";
+	pinctrl-0 = <&usb0_id_detect_pin>;
+	usb0_id_det-gpio = <&pio 7 4 GPIO_ACTIVE_HIGH>; /* PH4 */
 	status = "okay";
 };
-- 
2.4.9

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html



[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]
  Powered by Linux